Toro 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower User manual

Brand: Toro

Model: 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower

Category: Lawnmowers

Type: User manual

Form No. 3357-380 Rev B

21in Heavy-Duty

Recycler®/Rear Bagger Lawn

Mower

Model No. 22187 —Serial No. 270000001 and Up

Warning

CALIFORNIA

Pr oposition 65 W ar ning

T he engine exhaust fr om this pr oduct

contains chemicals kno wn to the State of

Calif or nia to cause cancer , bir th defects, or

other r epr oducti v e har m.

Important: T his engine is not equipped

with a spar k ar r ester muf ﬂer . It is a

violation of Calif or nia Public R esource Code

Section 4442 to use or operate the engine

on an y f or est-co v er ed, br ush-co v er ed, or

g rass-co v er ed land. Other states or federal

ar eas may ha v e similar la ws.

T his spark ignition system complies with Canadian

ICES-002

T he enclosed Engine Owner’ s Man ual is

supplied f or inf or mation r egarding the US

En vir onmental Pr otection Agency (EP A) and

the Calif or nia Emission Contr ol R egulation of

emission systems, maintenance, and w ar ranty .

R eplacements may be order ed thr ough the

engine man uf actur er .

Introduction

R ead this infor mation carefully to lear n ho w to

operate and maintain y our product properly and

to a v oid injur y and product damag e . Y ou are

responsible for operating the product properly

and safely .

Y ou ma y contact T oro directly at www .T oro .com

for product and accessor y infor mation, help

ﬁnding a dealer , or to register y our product.

W henev er y ou need ser vice , g en uine T oro par ts ,

or additional infor mation, contact an A uthorized

Ser vice Dealer or T oro Customer Ser vice and ha v e

the model and serial n umbers of y our product

ready . Figure 1 identiﬁes the location of the model

and serial n umbers on the product. W rite the

n umbers in the space pro vided.

Figure 1

1. Model and serial number plate

Model No.

Serial No.

T his man ual identiﬁes potential hazards and has

safety messag es identiﬁed b y the safety aler t

symbol ( Figure 2 ), whic h signals a hazard that ma y

cause serious injur y or death if y ou do not follo w

the recommended precautions .

Figure 2

1. Safety alert symbol

T his man ual uses 2 w ords to highlight infor mation.

Impor tant calls attention to special mec hanical

infor mation and Note emphasizes g eneral

infor mation w or th y of special attention.

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

General La wn Mo w er Safety . . . . . . . . . . . . . . . . 4

T raining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Pre paration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Maintenance and Storag e . . . . . . . . . . . . . . . . . . . . . 5

Safety and Instr uctional Decals . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1 Installing the Handle . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Installing the Star ter R ope . . . . . . . . . . . . . . . . . 8

3 Installing the Fuel T ank and the

Fuel Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 Installing the Disc harg e T unnel

Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5 Filling the Crankcase with Oil . . . . . . . . . . . . 9

Product Ov er view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chec king the Engine Oil Lev el . . . . . . . . . . . 12

Filling the Fuel T ank with

Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Star ting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Stopping the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the Self-propel Dri v e . . . . . . . . . . . . . . . . 15

Using the Disc harg e T unnel

Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the Cutting Height . . . . . . . . . . . . . 16

Using the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

R ecommended Maintenance

Sc hedule(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Lubricating the Pi v ot Ar ms . . . . . . . . . . . . . . . . 20

Lubricating the Gear Case . . . . . . . . . . . . . . . . . . 20

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Ser vicing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . 20

Changing the Engine Oil . . . . . . . . . . . . . . . . . . . . 21

Changing the Oil Filter . . . . . . . . . . . . . . . . . . . . . . 21

Ser vicing the Spark Plug . . . . . . . . . . . . . . . . . . . . 22

Fuel System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Emptying the Fuel T ank and

Cleaning the Fuel

Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Dri v e System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 23

Adjusting the Self-propel

Dri v e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Ser vicing the W heels . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Controls System Maintenance . . . . . . . . . . . . . . . . . . . . 24

Adjusting the Blade Brak e

Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Blade Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Maintaining the Cutting Blade . . . . . . . . . . . . 25

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Cleaning under the La wn Mo w er

Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Cleaning the Disc harg e T unnel and

Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Cleaning under the Belt Co v er . . . . . . . . . . . . 27

Storag e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Pre paring the Fuel System . . . . . . . . . . . . . . . . . . 28

Pre paring the Engine . . . . . . . . . . . . . . . . . . . . . . . . . 28

General Infor mation . . . . . . . . . . . . . . . . . . . . . . . . . 28

R emo ving the La wn Mo w er from

Storag e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Safety

T his la wn mo w er meets or ex ceeds the

CPSC blade safety r equir ements f or

w alk-behind r otar y la wn mo w er s and the

B71.4 speciﬁcations of the American National

Standards Institute in ef fect at the time of

pr oduction.

Impr oper l y using or maintaining this la wn

mo w er can r esult in injur y . T o r educe the

potential f or injur y , compl y with these safety

instr uctions.

T oro designed and tested this la wn mo w er for to

offer reasonably safe ser vice; ho w ev er , f ailur e to

compl y with the f ollo wing instr uctions may

r esult in per sonal injur y .

Engine exhaust contains carbon mono xide,

an odor less, deadl y poison that can kill y ou.

Do not r un the engine indoor s or in an

enclosed ar ea.

T o ensur e maximum safety , best perf or mance,

and to gain kno wledge of the pr oduct, it is

essential that y ou and an y other operator of

the la wn mo w er r ead and under stand the

contents of this man ual bef or e the engine is

ev er star ted. P ay par ticular attention to the

safety aler t symbol ( Figur e 2 ) which means

Caution, W ar ning , or Danger—“per sonal

safety instr uction.” R ead and under stand the

instr uction because it has to do with safety .

F ailur e to compl y with the instr uction may

r esult in per sonal injur y .

General Lawn Mower Safety

T his la wn mo w er is capable of amputating hands

and feet and of thro wing objects . F ailure to

obser v e the follo wing safety instr uctions could

result in serious injur y or death.

T he follo wing instr uctions are from the

ANSI/OPEI B71.4–2004 standard.

Training

• R ead the Operator’ s Man ual and other training

material.

• If the operator(s) or mec hanic(s) cannot read

English it is the o wner’ s responsibility to

explain this material to them.

• Become familiar with the safe operation of the

equipment, operator controls , and safety signs .

• All operators and mec hanics should be trained.

T he o wner is responsible for training the users .

• Nev er let c hildren or untrained people operate

or ser vice the equipment. Local regulations

ma y restrict the ag e of the operator .

• T he o wner/user can prev ent and is responsible

for accidents or injuries occur ring to

themselv es , other people or proper ty .

Preparation

• Ev aluate the ter rain to deter mine what

accessories and attac hments are needed to

properly and safely perfor m the job .

• Only use accessories and attac hments appro v ed

b y the man ufacturer .

• W ear appropriate clothing, including safety

glasses and hearing protection. Long hair ,

loose clothing or jew elr y ma y g et tangled in

mo ving par ts .

• Inspect the area where the equipment is to be

used and remo v e all objects suc h as roc ks , to ys

and wire whic h can be thro wn b y the mac hine .

• Use extra care when handling g asoline and

other fuels .

– T hey are ﬂammable and v apors are

explosi v e .

– Use only an appro v ed container .

– Nev er remo v e g as cap or add fuel when

engine is r unning .

– Do not smok e .

– Nev er refuel or drain the mac hine indoors .

• Chec k that operator’ s presence controls ,

safety switc hes and shields are attac hed and

functioning properly . Do not operate unless

they are functioning properly .

Operation

• Nev er r un an engine in an enclosed area.

• Only operate in g ood light, k ee ping a w a y from

holes and hidden hazards .

• Be sure all dri v es are in neutral and parking

brak e is eng ag ed before star ting engine .

• Only star t engine from the operator’ s position.

• Be sure of y our footing while using pedestrian

controlled equipment, especially when bac king

up .

• W alk, don ’ t r un.

• Nev er operate on w et g rass . R educed footing

could cause slipping .

• Slo w do wn and use extra care on hillsides . Be

sure to tra v el in the recommended direction

on hillsides .

• Use caution while operating near drop-offs .

• Slo w do wn and use caution when making tur ns

and when c hanging directions on slopes .

• Nev er raise dec k with the blades r unning .

• Nev er operate with the disc harg e deﬂector

raised, remo v ed or altered, unless using a g rass

catc her .

• Do not c hang e the engine g o v er nor setting or

o v erspeed the engine .

• Stop on lev el g round and shut off engine

before lea ving the operator’ s position for any

reason including emptying the catc hers or

unclog ging the c hute .

• Stop equipment and inspect blades after

striking objects or if an abnor mal vibration

occurs . Mak e necessar y re pairs before

resuming operations .

• K ee p hands and feet a w a y from the cutting

units .

• Look behind and do wn before bac king up to

be sure of a clear path.

• Be a w are of the mo w er disc harg e direction and

do not point it at any one .

• Do not operate the mo w er under the inﬂuence

of alcohol or dr ugs .

• Use care when loading or unloading the

mac hine into a trailer or tr uc k.

• Use care when approac hing blind cor ners ,

shr ubs , trees , or other objects that ma y obscure

vision.

Maintenance and Storage

• W ait for all mo v ement to stop before adjusting,

cleaning or re pairing .

• Clean g rass and debris from cutting unit,

m ufﬂer , and engine to help prev ent ﬁres .

• Clean up oil or fuel spillag e .

• Let engine cool before storing and do not store

near ﬂame .

• Do not store fuel near ﬂames or drain indoors .

• Nev er allo w untrained personnel to ser vice

mac hine .

• Use care when c hec king blade .

• W rap the blade or w ear glo v es , and use caution

when ser vicing .

• Only re place blade . Nev er straighten or w eld

them.

• K ee p hands and feet a w a y from mo ving par ts .

• If possible , do not mak e adjustments with the

engine r unning .

• K ee p all par ts in g ood w orking condition and

all hardw are tightened.

• R e place all w or n or damag ed decals .

Safety and Instructional Decals

Safety decals and instr uctions are easily visible to the operator and are located near any

area of potential dang er . R e place any decal that is damag ed or lost.

Manufacturer’s Mark

1. Indicates the blade is identied as a part from the original

machine manufacturer.

39-5770

68-7410

74-1970

1. Transmission speeds 2. Neutral

98-4387

1. Warning—wear hearing protection.

106-0690

110-4989

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Handle

Bolt (5/16 x 1-1/4 inches)

Washer

Thin locknut (5/16 inch)

Bolt (5/16 x 1-1/2 inches)

Locknut (5/16 inch)

Bag support rod

Cap locknut

Cable tie

Install the handle.

No parts required

–

Install the starter rope.

Self-tapping screw

Fuel tank

Install the fuel tank and fuel line.

Discharge tunnel plug

Install the discharge tunnel plug.

No parts required

–

Fill the crankcase with oil.

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Step

Installing the Handle

Parts needed for this step:

Handle

Bolt (5/16 x 1-1/4 inches)

Washer

Thin locknut (5/16 inch)

Bolt (5/16 x 1-1/2 inches)

Locknut (5/16 inch)

Bag support rod

Cap locknut

Cable tie

Procedure

1. Mount the handle to the outside of the la wn

mo w er housing (using the bottom hole) with 2

bolts (5/16 x 1-1/4 inc hes), w ashers , and thin

loc kn uts (5/16 inc h) ( Figure 3 ).

Figure 3

1. Handle latch

3. Cap locknut (2)

2. Bag support rod 4. Handle

2. Secure the handle latc hes to the handle with

2 bolts (5/16 x 1-1/2 inc hes), w ashers , and

loc kn uts (5/16 inc h) ( Figure 3 ).

Note: Y ou can adjust the handle height

for comfor table operation. Stand behind the

handle to deter mine the height. T o adjust the

handle height, position the cap screws and the

loc kn uts that secure the handle latc hes to the

handle into the other mounting holes in the

latc hes .

3. Slide the bag suppor t rod through the second

from the top mounting holes in the handle and

secure eac h end with a cap loc kn ut ( Figure 3 ).

4. Use a cable tie to secure the control cables to

the left handle belo w the bag suppor t rod.

Step

Installing the Starter Rope

No Parts Required

Procedure

Pull the star ter rope through the rope guide on the

handle ( Figure 4 ).

Figure 4

1. Starter rope

2. Rope guide

Note: T o mak e the rope easier to install, squeeze

the control bar on the handle .

Step

Installing the Fuel Tank and

the Fuel Line

Parts needed for this step:

Self-tapping screw

Fuel tank

Procedure

1. Slide the end of the fuel line onto the elbo w

ﬁtting ( Figure 5 ).

Figure 5

1. Fuel tank 3. Fuel line

2. Elbow tting 4. Fuel line clamp

2. Secure the fuel line in place with the fuel line

clamp ( Figure 5 ).

3. Slide the plastic clips on the front of the fuel

tank onto the fuel tank mount ( Figure 6 ).

Figure 6

1. Plastic clip (2)

4. Secure the bottom of the fuel tank to the

fuel tank brac k et b y installing the self-tapping

screws from the bottom. Do not o v er tighten

the scr ews.

Step

Installing the Discharge

Tunnel Plug

Parts needed for this step:

Discharge tunnel plug

Procedure

1. Open the disc harg e door b y pulling forw ard on

the handle and mo ving it rearw ard ( Figure 7 ).

Hold the disc harg e door handle to prev ent the

spring-loaded door from closing while y ou

inser t the plug .

Figure 7

1. Discharge door handle 2. Plug, rotated clockwise

2. Since the plug is slightly wider than the

disc harg e tunnel opening, rotate the plug

cloc kwise slightly while inser ting it ( Figure 7 ).

Note: Ensure that the ar ro w on the plug

decal points upw ard.

3. Push the plug all the w a y in until the spring clip

on the bottom of the plug clic ks into place ,

loc king the plug securely into the disc harg e

tunnel ( Figure 8 ).

Figure 8

1. Spring clip

4. R elease the disc harg e door handle to loc k the

top of the plug .

Step

Filling the Crankcase with

Oil

No Parts Required

Procedure

T he engine crankcase is shipped without oil.

Y ou m ust ﬁll it with appro ximately 30 ounces

(0.88 l) of oil before star ting the engine . R efer

to Chec king the Engine Oil Lev el in Operation ,

pag e 12 for oil speciﬁcations and instr uctions .

Product Overview

Figure 9

1. Handle 6. Air lter

2. Throttle control lever 7. Cutting height lever

3. Grass bag 8. Spark plug

4. Fuel tank 9. Oil ll/dipstick

5. Oil lter 10. Blade control bar

Controls

Figure 10

1. Blade control bar 3. Recoil starter handle

2. Throttle control lever

Operation

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Eac h time before y ou mo w , mak e sure that the

self-propel dri v e and the blade control bar operate

properly . W hen y ou release the blade control bar ,

the blade and self-propel dri v e should stop . If they

do not, contact an A uthorized Ser vice Dealer .

T his machine pr oduces sound lev els in

ex cess of 85dB A at the operator’ s ear and

can cause hearing loss thr ough extended

periods of exposur e.

W ear hearing pr otection when operating

this machine.

Figure 11

1. Warning—wear hearing protection.

Checking the Engine Oil

Level

Initially , ﬁll the crankcase with 30 ounces (0.88

liters) of oil. Use only high-quality SAE 30 or SAE

10W30 w eight deterg ent oil that has the American

P etroleum Institute (API) ser vice classiﬁcation SF ,

SG , SH, or SJ .

Oil Capacity

With oil lter

30 ounces (0.88 L)

Without oil lter

24 ounces (0.70 L)

Before eac h use , ensure that the oil lev el is betw een

the Add and Full marks on the dipstic k ( Figure 12 ).

Figure 12

1. Dipstick 3. Add

2. Full

Note: W hen the crankcase is empty , pour

about 3/4 of the crankcase capacity of oil in

the crankcase , then follo w the procedure in this

section.

1. Mo v e the la wn mo w er to a lev el surface .

2. Clean around the dipstic k ( Figure 12 ).

3. R emo v e the dipstic k b y rotating the cap

countercloc kwise and pulling it out.

4. Wipe the dipstic k clean with a clean cloth.

5. Inser t the dipstic k into the ﬁller nec k, then

remo v e it.

Note: T o ensure an accurate oil lev el reading,

y ou m ust fully install the dipstic k.

6. R ead the oil lev el on the dipstic k ( Figure 12 ).

7. If the oil lev el reading is belo w the Add mark

on the dipstic k, slo wly pour only enough oil

into the ﬁller hole to raise the oil lev el to the

Full mark on the dipstic k.

Important: Do not o v erﬁll the crankcase

with oil and r un the engine; engine dama ge

will r esult. Drain the ex cess oil until the oil

lev el on the dipstick r eads Full.

8. Inser t the dipstic k into the ﬁller nec k and

rotate the cap cloc kwise until it is tight.

Filling the Fuel Tank with

Gasoline

F or best results , use clean, fresh, lead-free g asoline

with an octane rating of 87 or higher . T o ensure

freshness , purc hase only the quantity of g asoline

that y ou expect to use in 30 da ys . Using unleaded

g asoline results in few er combustion de posits and

long er engine life . Y ou ma y use leaded g asoline if

unleaded g asoline is not a v ailable .

Important: Do not add oil to the gasoline.

Important: Do not use methanol, gasoline

containing methanol, gasohol containing

mor e than 10% ethanol, pr emium gasoline, or

white gas. Using these fuels can dama ge the

engine’ s fuel system.

Important: Do not use gasoline that has

been stor ed since the last mo wing season or

longer .

In cer tain conditions, gasoline is extr emel y

ﬂamma ble and highl y explosi v e. A ﬁr e or

explosion fr om gasoline can bur n y ou and

other s and can dama ge pr oper ty .

• Fill the fuel tank outdoor s, in an open

ar ea, and when the engine is cold. W ipe

up an y gasoline that spills.

• Do not ﬁll the fuel tank completel y full.

Add gasoline to the fuel tank until the

lev el is 1/4 to 1/2 in. (6 to 13 mm) belo w

the bottom of the ﬁller neck. T his empty

space in the tank allo ws the gasoline to

expand.

• Nev er smok e when handling gasoline,

and stay a w ay fr om an open ﬂame or

wher e a spar k may ignite the gasoline

fumes.

• Stor e gasoline in an appr o v ed fuel

container and k eep it out of the r each of

childr en.

• Nev er buy mor e than a 30-day suppl y of

gasoline.

W hen fueling , under cer tain circumstances,

a static charge can dev elop , igniting the

gasoline. A ﬁr e or explosion fr om gasoline

can bur n y ou and other s and dama ge

pr oper ty .

• Al w ays place gasoline container s on

the g r ound and a w ay fr om y our v ehicle

bef or e ﬁlling .

• Do not ﬁll gasoline container s inside

a v ehicle or on a tr uck or trailer bed

because interior car pets or plastic tr uck

bed liner s may insulate the container and

slo w the loss of an y static charge.

• W hen practical, r emo v e

gasoline-po w er ed equipment fr om

the tr uck or trailer and r efuel the

equipment with its wheels on the r ound.

• If this is not possible, then r efuel such

equipment on a tr uck or trailer fr om a

por ta ble container , not fr om a gasoline

dispenser nozzle.

• If y ou must use a gasoline dispenser

nozzle, k eep the nozzle in contact with

the rim of the fuel tank or container

opening at all times until fueling is

complete.

Use a fuel stabilizer/conditioner regularly during

operation and storag e . A stabilizer/conditioner

cleans the engine during operation and prev ents

gum-lik e v ar nish de posits from for ming in the

engine during periods of storag e .

Important: Do not use fuel additi v es other

than a fuel sta biliz er/conditioner . Do not use

fuel sta biliz er s with an alcohol base such as

ethanol, methanol, or isopr opanol.

1. Clean around the fuel tank cap ( Figure 13 ).

Figure 13

1. Oil ll/dipstick 3. Air cleaner

2. Fuel tank cap 4. Spark plug

2. R emo v e the cap from the tank.

3. Fill the fuel tank with unleaded g asoline to

within 1/4 to 1/2 inc h (6 to 13 mm) from the

top of the tank. Do not ﬁll into the ﬁller

neck.

Important: Do not ﬁll the tank mor e

than 1/4 inch (6 mm) fr om the top of the

tank because the gasoline must ha v e r oom

to expand.

4. Install the fuel tank cap and wipe up any spilled

g asoline .

Starting the Engine

1. Connect the wire to the spark plug ( Figure 13 ).

2. Open the fuel v alv e ( Figure 23 ).

3. Mo v e the throttle control to the Chok e

position.

4. Mo v e the g round speed control to the Neutral

(N) position ( Figure 14 ).

Figure 14

1. Ground speed control

5. Pull the star ter handle lightly until y ou feel

resistance , then pull it shar ply .

6. R egulate the throttle and the g round speed

control as desired when the engine star ts .

Note: If the engine fails to star t after 3 pulls ,

re peat ste ps 3 through 6 .

Stopping the Engine

1. R elease the blade control bar and mo v e the

throttle control to the Off position.

2. Disconnect the wire from the spark plug if y ou

do not use the la wn mo w er or if y ou lea v e it

unattended.

Using the Self-propel Drive

T he la wn mo w er has 3 g round speeds: 1 is slo w , 2

is medium, and 3 is fast. the g round speed control

is located at the rear of the belt co v er ( Figure 15 ).

Figure 15

1. Ground speed control

1. Mo v e the g round speed control to the Neutral

(N) position.

2. Star t the engine .

3. Squeeze the blade control bar ag ainst the

handle to the R un/Dri v e position ( Figure 16 ).

Figure 16

1. Run/Drive position

3. Stop position

2. Run/Shift position

Note: Do not shift speeds while y ou squeeze

the blade control bar ag ainst the handle in

the R un/Dri v e position; this can damag e the

transmission. Mo v e the blade control bar to

the R un/Shift position ( Figure 16 ) when y ou

c hang e the g round speed.

Note: Y ou can v ar y the g round speed b y

increasing or decreasing the distance betw een

the control bar and the handle . Lo w er the

control bar to slo w the la wn mo w er when

making a tur n or if the la wn mo w er is mo ving

too fast for y ou. If y ou lo w er the control bar

too far , the la wn mo w er stops self-propelling .

Squeeze the control bar closer to the handle to

increase the g round speed. W hen y ou hold the

control bar tight ag ainst the handle , the la wn

mo w er self-propels at the maxim um g round

speed. Mo v e the g round speed control to the

Neutral (N) position when y ou use the la wn

mo w er for trimming and whenev er y ou lea v e

the la wn mo w er .

Using the Discharge Tunnel

Plug

1. Stop the engine and w ait for all mo ving par ts

to stop .

2. Inser t the plug; refer to Installing the Disc harg e

T unnel Plug .

3. T o remo v e the plug, mo v e the disc harg e door

handle rearw ard and lift up the spring clip

on the bottom of the plug . W hen the plug is

unloc k ed, pull it out of the disc harg e tunnel.

Note: W hen g rass is thic k and lush, clippings

ma y collect on and around the disc harg e

tunnel plug . T his ma y mak e remo ving the plug

difﬁcult. Clean the plug thoroughly after eac h

use .

Adjusting the Cutting

Height

Eac h wheel is adjusted indi vidually with a wheel

height adjustment lev er . Cutting heights are 1 inc h

(25 mm), 1-1/2 inc hes (38 mm), 2 inc hes (51 mm),

2-1/2 inc hes (64 mm), 3 inc hes (76 mm), and

3-1/2 inc hes (89 mm).

Adjusting the cutting height lev er s could

bring y our hands into contact with a mo ving

blade and r esult in serious injur y .

• Stop the engine and w ait f or all

mo v ement to stop bef or e adjusting the

cutting height.

• Do not put y our ﬁnger s under the

housing when adjusting the cutting

height.

1. Pull the wheel height adjustment lev er to w ard

the wheel ( Figure 17 ) and mo v e it to the

desired setting .

Figure 17

1. Wheel height adjustment lever

2. R elease the wheel height adjustment lev er and

seat it securely in the notc h.

3. Adjust all the wheels to the same cutting height

setting .

Using the Grass Bag

Occasionally , y ou ma y wish to use the g rass bag

for bag ging extra long g rass , lush g rass , or lea v es .

Installing the Grass Bag

1. Stop the engine and w ait for all mo ving par ts

to stop .

2. Ensure that the disc harg e door handle is fully

forw ard and that the pin is eng ag ed in the

catc h ( Figure 18 ).

Figure 18

1. Bag frame on retaining

post

3. Handle fully forward;

discharge door closed

2. Pin engaged in catch

3. Slide the hole in the bag frame onto the

retaining post on the disc harg e tunnel

( Figure 18 ).

4. Set the rear of the bag frame onto the bag

suppor t rod.

5. Pull the disc harg e door handle forw ard until

the pin clears the catc h, and mo v e the handle

rearw ard until the pin loc ks in the bag notc h

( Figure 19 ).

Figure 19

1. Pin locked in bag notch

Note: T he disc harg e door in the la wn mo w er

housing is no w open.

Mowing with the Grass Bag

A w or n g rass ba g could allo w small stones

and other similar de bris to be thr o wn in the

operator’ s or bystander’ s dir ection and r esult

in serious per sonal injur y or death to the

operator or bystander s.

Check the g rass ba g fr equentl y . If it is

dama ged, install a new T or o r eplacement

ba g .

Removing the Grass Bag

1. Stop the engine and w ait for all mo ving par ts

to stop .

2. Raise the disc harg e door handle and mo v e

it forw ard to eng ag e the pin with the catc h

( Figure 18 ).

3. Grasp the handles at the front and the rear of

the bag and lift the bag off the la wn mo w er .

4. Gradually tip the bag forw ard to empty the

clippings .

5. T o install the bag, refer to Installing the Grass

Bag .

If the discharge door does not close

completel y , the la wn mo w er could thr o w

objects, causing serious per sonal injur y or

death.

If y ou cannot close the door because the

g rass clippings clo g the discharge ar ea, stop

the engine and gentl y mo v e the discharge

door handle back and f or th until y ou can

close the door completel y . If y ou still cannot

close the door , r emo v e the obstr uction with

a stick, not y our hand.

T he la wn mo w er can thr o w g rass clippings

and other objects thr ough an open discharge

tunnel. Objects thr o wn with enough f orce

could cause serious per sonal injur y or death

to the operator or bystander .

Nev er open the door on the discharge tunnel

when the engine is r unning .

Operating Tips

General Tips

• R eview the safety instr uctions and read this

man ual carefully before operating the la wn

mo w er .

• Clear the area of stic ks , stones , wire , branc hes ,

and other debris that the blade could hit and

thro w .

• K ee p ev er y one , especially c hildren and pets ,

a w a y from the area of operation.

• A v oid striking trees , w alls , curbs , or other solid

objects . Nev er deliberately mo w o v er any

object.

• If the la wn mo w er strik es an object or star ts

to vibrate , immediately stop the engine ,

disconnect the wire from the spark plug, and

examine the la wn mo w er for damag e .

• Maintain a shar p blade throughout the cutting

season. P eriodically ﬁle do wn nic ks on the

blade .

• R e place the blade when necessar y with an

original T oro re placement blade .

• Mo w only dr y g rass or lea v es . W et g rass and

lea v es tend to clump on the yard and can cause

the la wn mo w er to plug or the engine to stall.

W et g rass or lea v es can cause serious

injur y if y ou slip and contact the blade.

Mo w onl y in dr y conditions.

• Clean the underside of the la wn mo w er dec k

after eac h mo wing . See Cleaning the Underside

of the La wn Mo w er Housing .

• K ee p the engine in g ood r unning condition.

• Set the engine speed to the fastest position for

the best cutting results .

Operating a la wn mo w er with its engine

r unning at a speed g r eater than the

f actor y setting can cause the la wn mo w er

to thr o w a par t of the blade or engine into

the operator’ s or bystander’ s ar ea and

r esult in serious per sonal injur y or death.

– Do not change the engine speed

setting .

– If y ou suspect the engine speed

is f aster than nor mal, contact an

Authoriz ed Ser vice Dealer .

• Clean the air ﬁlter frequently . Mulc hing stirs

up more clippings and dust whic h clogs the air

ﬁlter and reduces engine perfor mance .

Cutting Grass

• Grass g ro ws at different rates at different times

of the year . In the summer heat, it is best to

cut g rass at the 2 inc h (51 mm), 2-1/2 inc h (64

mm), or 3 inc h (76 mm) cutting height settings .

Cut only about a third of the g rass blade at a

time . Do not cut belo w the 2 inc h (51 mm)

setting unless the g rass is sparse or it is late fall

when g rass g ro wth begins to slo w do wn.

• W hen cutting g rass o v er 6 inc hes (15 cm) tall,

ﬁrst mo w at the highest cutting height setting

and w alk slo w er; then mo w ag ain at a lo w er

setting for the best la wn appearance . If the

g rass is too long and the lea v es clump on top

of the la wn, the la wn mo w er ma y plug and

cause the engine to stall.

• Alter nate the mo wing direction. T his helps

disperse the clippings o v er the la wn for ev en

fer tilization.

If the ﬁnished la wn appearance is unsatisfactor y ,

tr y one or more of the follo wing:

• Shar pen the blade .

• W alk at a slo w er pace while mo wing .

• Raise the cutting height on y our la wn mo w er .

• Cut the g rass more frequently .

• Ov erlap cutting sw aths instead of cutting a full

sw ath with eac h pass .

• Set the cutting height on the front wheels one

notc h lo w er than the rear wheels . F or example ,

set the front wheels at 2 inc hes (51 mm) and

the rear wheels at 2-1/2 inc hes (64 mm).

Cutting Leaves

• After cutting the la wn, ensure that half of the

la wn sho ws through the cut leaf co v er . Y ou

ma y need to mak e more than one pass o v er

the lea v es .

• F or light leaf co v erag e , set all the wheels at the

same cutting height setting .

• If there are more than 5 inc hes (12.7 cm) of

lea v es on the la wn, set the front cutting height

1 or 2 notc hes higher than the rear cutting

height. T his mak es it easier to feed the lea v es

under the la wn mo w er dec k.

• Slo w do wn y our mo wing speed if the la wn

mo w er does not cut the lea v es ﬁnely enough.

• If y ou mo w o v er oak lea v es , y ou can add lime

to the g rass in the spring to reduce the acidity

of the oak lea v es .

Maintenance

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the rst 8 operating

hours

• Change the engine oil without the oil lter.

Before each use or daily

• Check the engine oil level.

• Ensure that the engine stops within 3 seconds after releasing the blade

control bar.

• Inspect the mower blades for wear or damage.

• Clean under the lawn mower housing.

• Clean the discharge tunnel and plug.

Every 25 hours

• Lubricate the pivot arms.

• Clean the foam pre-cleaner (more frequently in dusty conditions).

Every 50 hours

• Change the engine oil (more often in dusty conditions).

• Check the fuel hose and replace it if necessary.

• Clean under the belt cover.

Every 100 hours

• Lubricate the gear case.

• Clean the air cooling ns.

• Change the engine oil and oil lter.

• Check the spark plug.

• Clean the fuel lter.

• Adjust the self-propel drive.

• Service the wheels.

• Adjust the blade brake cable.

Every 300 hours

• Replace the paper air lter (more frequently in dusty conditions).

Yearly or before storage

• Empty the fuel tank.

Important: R efer to y our Engine Operator’ s Man ual f or additional maintenance pr ocedur es.

If y ou lea v e the wir e on the spar k plug , someone could accidentl y star t the engine and

seriousl y injur e y ou or other bystander s.

Disconnect the wir e fr om the spar k plug bef or e y ou do an y maintenance. Set the wir e aside so

that it does not accidentl y contact the spar k plug .

Lubrication

Lubricating the Pivot Arms

After ev er y 25 operating hours or when the season

ends , lubricate the pi v ot ar ms .

1. Mo v e the rear wheel cutting height lev ers to

the center setting .

2. Wipe the g rease ﬁttings with a clean rag

( Figure 20 ).

Figure 20

1. Grease tting

3. Install a g rease gun onto the ﬁtting and g ently

apply 2 or 3 pumps of #2 m ulti-pur pose

lithium-base g rease .

Important: Ex cessi v e g r ease pr essur e

may dama ge the seals.

Lubricating the Gear Case

After ev er y 100 operating hours , g rease the g ear

case .

1. R emo v e the g rass bag .

2. Install a g rease gun onto the ﬁtting through the

belt co v er opening ( Figure 21 ).

Figure 21

1. Belt cover 2. Grease tting

3. Gently apply one to 2 pumps of #2

m ulti-pur pose lithium-base g rease .

4. Install the g rass bag .

Engine Maintenance

Servicing the Air Filter

Clean the foam pre-cleaner ev er y 25 operating

hours . R e place the paper air ﬁlter once ev er y

season or ev er y 300 operating hours; re place it

more frequently in dusty conditions .

Important: Do not operate the engine

without the air ﬁlter assembl y; extr eme engine

dama ge will occur .

1. Stop the engine and w ait for all mo ving par ts

to stop .

2. Disconnect the wire from the spark plug

( Figure 13 ).

3. R emo v e the co v er and clean it thoroughly

( Figure 22 ).

Figure 22

1. Cover

3. Air lter base

2. Paper air lter

4. R emo v e and inspect the paper air ﬁlter

( Figure 22 ), and discard it if it is ex cessi v ely

dir ty .

Important: Do not tr y to clean a paper

ﬁlter .

Page is loading ...

Toro 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower User manual

Brand: Toro

Model: 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower

Category: Lawnmowers

Type: User manual

Download PDF

report

Toro 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower User manual

Toro 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower User manual

Related papers

Other documents