Moen DN7015 Installation guide

Type
Installation guide

Moen DN7015 is a toilet safety rail designed to provide additional support and stability for individuals who have difficulty getting on and off the toilet. It is made from anodized aluminum with a powder coated white finish and features high impact molded white polyethylene armrests. The rail has a maximum user weight of 250lbs and comes with all the necessary hardware for installation.

To install the rail, simply connect the armrests to the main tubing, add the mounting brackets, remove the toilet seat, position the safety bar, place the bar clamps, and re-attach the seat. The rail should be positioned so that the flat bar is not hanging over the front rim of the bowl and the bar clamps are aligned with the toilet seat mounting holes.

Moen DN7015 is a toilet safety rail designed to provide additional support and stability for individuals who have difficulty getting on and off the toilet. It is made from anodized aluminum with a powder coated white finish and features high impact molded white polyethylene armrests. The rail has a maximum user weight of 250lbs and comes with all the necessary hardware for installation.

To install the rail, simply connect the armrests to the main tubing, add the mounting brackets, remove the toilet seat, position the safety bar, place the bar clamps, and re-attach the seat. The rail should be positioned so that the flat bar is not hanging over the front rim of the bowl and the bar clamps are aligned with the toilet seat mounting holes.

Toilet Safety Rail is made from
anodized aluminum with a powder
coated white finish. Armrests are high
impact molded white polyethylene.
WARNING
This product has a maximum user weight of
250lbs. Contact CSI Customer Service
immediately at 1-800-882-0116 if any
components are damaged or missing.
Making substitutions or modifying this
product in any way will void your warranty.
CSI assumes no liability for any damage or
injury caused by improper assembly,
installation or use of this product.
q
DN7015
Toilet Safety Rail
White
Photo Box Packaging with Handle
25300 AL MOEN DRIVE NORTH OLMSTED, OH 44070 (800) 321-8809
FAX: (800) 848-6636 INTERNATIONAL: (440) 962-2000
FAX: (440) 962
-
2726 CUSTOMER SERVICE (USA): 800
-
-
0116
1. Connect armrest at back inserting left hand sleeve into right
hand tubing.
2.
Connect armrest at front fastening flat bar to open ends of right
and left tubing with 1 ½” slotted screws provided.
3. Add mounting brackets. Place grooved bracket over tubing at
the back of toilet safety rail so that the tabs are pointing toward
the flat bar at front. Align slots with holes in tubing with 1”
screws provided.
4. Remove toilet seat. Unscrew toilet seat bolts nuts at the rear
underside of toilet bowl. Remove bolts and seat.
5. Position safety bar. Place assembled toilet safety rail directly
on toilet bowl with flat bar to the front. The flat bar should not
be hanging over the front rim of the bowl.
6. Position clamps. Place bar clamps so that they are over the
tubing and align with the toilet seat mounting holes.
7. Re-attach seat. Place toilet seat in position over toilet safety
rail so that mounting holes of seat, safety rail and toilet are
aligned. Insert toilet seat mounting bolts and tighten bolt nuts.
Stock Number:
___________________Toilet Safety Rail
By CSI Bath Furnishings
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
Toilet Safety Rail
DN7015
Home Care Technical Specification
Copyright CSI Bath Furnishing Division of Moen 02/22/01
  • Page 1 1

Moen DN7015 Installation guide

Type
Installation guide

Moen DN7015 is a toilet safety rail designed to provide additional support and stability for individuals who have difficulty getting on and off the toilet. It is made from anodized aluminum with a powder coated white finish and features high impact molded white polyethylene armrests. The rail has a maximum user weight of 250lbs and comes with all the necessary hardware for installation.

To install the rail, simply connect the armrests to the main tubing, add the mounting brackets, remove the toilet seat, position the safety bar, place the bar clamps, and re-attach the seat. The rail should be positioned so that the flat bar is not hanging over the front rim of the bowl and the bar clamps are aligned with the toilet seat mounting holes.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI