Product detail parameters
The using manual of the
pure sine wave inverter
Power Inverter
Solar Power Generation System
WARNING
Prohibit parallel connected with municipal electricity
The inverter would be damaged when the output parallel connected with municipal
electricity,Leading to the danger of touching the electric.
Prohibit Minors use.
Don't use the inverter for minors. Because the output of inverter is high voltage,
Leading to the danger happen for touching the electric
Prohibit uninstall
Don't uninstall and modify the inverter, leading to the fault of inverter if uninstall and
modify the inverter, and other accident include fire or touch electric etc.
Prohibit touch with club
Don't put club and other metal something at near hole and socket of the inverter.
Leading to the fault of the touch electric and damage the inverter.
Prohibit touch with wet hand.
Don't touch the inverter and the plug with wet hand ,otherwise leading the touch
electric and other safety accident.
Keep away the flame and high temperature area
The inverter and battery will happen fire and exploded when the inverter work at
near the high temperature and flame area.
Prohibit knock
Knocking the inverter ,leading to the inverter damaged and other safety problem .
Prohibit use to the medical equipment.
The inverter don't use for the medical equipment ,Because of don't test and check
the equipment.
The character of product
●The company's pure sine series inverter with perfect protection circuit, providing high
temperature protection, over-voltage protection, low-voltage protection, short-circuit
protection, overload protection and other functions to prevent damage to your inverter;
●Advanced circuit design, high conversion efficiency, rich interface, stable output voltage;
●The inverter adopts metal shell, reasonable design and good heat dissipation
characteristic.
●The inverter has advanced anti-jamming technology, complete function protection
circuit and soft start circuit, convenient operation mode.
●The soft-start circuit has the ability to raise the output voltage step by step during
startup to eliminate the cold start failure, and at the same time, it has the output
voltage instantaneous. Drop-down and fast recovery function to reduce the load on
the instant overload.
Please connect to the ground wire
In order to using electric safety,Please connect to the ground wire otherwise
leading to the safety accident.
Prevent wet and water
Notice the preventing wet and water,Because of the wet and water,the inverter may
be damaged ,Leading to the fire and short circuit ,touch electric accident etc.
Please insert fully.
Please insert fully the load equipment's plug to the inverter power socket. if
the plug isn't inserted fully .Leading to the touch electric and over heat ,even
leading to the fire. Prohibit use the bad plug,socket, and electric wire.
In order to ensure reliable service for you ,the inverter
must be installed and used by the correct way. Please
reading the installing and operation manual before
installing and using. please especially notice the Alarm
and illustrate alarm. To some possible inverter damaged
that these used condition and used way is reminded. To
some possible damage to people ,which give any serious
alarm notice. Please carefully read the manual of the
product, which in order to correct use .Especially read
the notice of safety precautions, and safety used.
The security attention considered.
(must be read and remember)
To avoid the injure to you and other person.we give
to as fellows notices,Please be sure compliance.The
means all kinds of symbols,Please refer to the
instruction. Warning: please read carefully,the as
follow content may harm person
Easy flammable gas
Ensure no flammable gas before connect,The sparking will be brought when connect
the battery.
The battery can bring the flammable gas when the battery is charged and discharged.
so the good vent should be keep.Don't put at some place of bringing flammable gas.
This series of Pure sine wave inverter is suitable for:
Various kinds of household appliances, lighting electricity, IT electronics products, office
equipment, Power tools, on-board appliances, outdoor emergency power supply, etc. The
power of the electrical equipment exceeds the output power of the inverter and some
star t-up current of large power equipment may not be driven.
300W 500W 800W 1000W
600W 1000W
110V / 220V(selectable)
110V / 220V(selectable)
1600W 2000W
12V/24V/48V
(selectable)
24V/48V(selectable)
12V / 24V(selectable)
10-15V(12V) / 20-30V(24V) / 40-60V(48V)
0.9A(12V)
0.5A(24V)
1.0A(12V)
0.6A(24V)
0.8A(12V)
0.6A(24V)
1.5A(12V)
0.8A(24V)
0.4A(48V)
211.5*118*56 236*118*56 309*180*142 367*150*76
0.81 0.91 3.05 2.44
≥90%
10V±0.5V(12V) / 20V±1V(24V) / 40V±2V(48V)
10.5V±0.5V(12V) / 21V±1V(24V) / 42V±2V(48V)
15.5V±0.5V(12V) / 30V±1V(24V) / 60V±2V(48V)
BEP800S
1500W 2000W 3000W 5000W
3000W 4000W 6000W 10000W
12V / 24V / 48V(selectable)
10-15V(12V) / 20-30V(24V) / 40-60V(48V)
384*180*142 454*180*142 529*180*142 685*180*167
4 4.9 6.02 8
≥90%
10V±0.5V(12V) / 20V±1V(24V) / 40V±2V(48V)
10.5V±0.5V(12V) / 21V±1V(24V) / 42V±2V(48V)
15.5V±0.5V(12V) / 30V±1V(24V) / 60V±2V(48V)
BEP1500S BEP2000S BEP3000S BEP5000S
3.8A(12V)
2.0A(24V)
1.2A(48V)
2.5A(24V)
1.4A(48V)
1.8A(12V)
1.0A(24V)
0.5A(48V)
3.0A(12V)
1.5A(24V)
0.8A(48V)
50Hz / 60Hz(selectable)
50Hz / 60Hz(selectable)
Pure Sine Wave
Pure Sine Wave
High temperature protection、Shortcircuit Protection、Overload Protection
High temperature protection、Shortcircuit Protection、Overload Protection
Intelligent fan, high temperature, load self start
Intelligent fan, high temperature, load self start
Support
No-support
No-support
No-support
Support
Support
Support
USB
Weight(kg)
Rated Power
Peak Power
Output voltage
Frequency
Output
Input
Input
protected
of
battery
WaveForm
Battery
Voltage
Rang Voltage
Alarm voltage of
low voltage
Protected voltage of
battery low voltage
Protected voltage of
battery high voltage
Anti-connected
protect batter y
Other protect
FAN
Working environment
Dimension(mm)
Efficiency
Open Circuit
Losses
T Y P E
USB
Weight(kg)
Rated Power
Peak Power
Output voltage
Frequency
Output
Input
Input
protected
of
battery
WaveForm
Battery
Voltage
Rang Voltage
Alarm voltage of
low voltage
Protected voltage of
battery low voltage
Protected voltage of
battery high voltage
Anti-connected
protect batter y
Other protect
FAN
Working environment
Dimension(mm)
Efficiency
Open Circuit
Losses
T Y P E
Working temperature 0-40 ℃ @ 100% load, working humidity 20-90 RH, no refrigeration
Working temperature 0-40 ℃ @ 100% load, working humidity 20-90 RH, no refrigeration
Inverter is a kind of equipment of that it will change the direct current (including the Batteries,
solar cells, wind turbines, etc) to alter tnating current. because of the high frequency exchange
technology is used by the inverter. and using the ferrite transformer replace the old bulky silicon
steel. This is the reason why our company product of the inver ter is lighter than another similar
product. The output wave form is the pure sine wave. It's wave form is the same with the commercial
Electric power.The general load power is driven by the inverter unless the load power is higher than
the output of the inverter.
In order to get the best used effect. Please put the inverter on the flat surface, example the
ground ,the floor of automobile, or other of the surface of solid. and it is easy that fix the inverter's
power line. the working place should be satisfaction the as follow standard:
1. Keeping the dry, Don't Let the inverter is touched the water and other liquid. Keep the inverter
away the wet place and water.
2. The cool environment temperature is at o degree(not dew) to 40degree.Don't put the inver ter at
the heating vent or near by the heating equipment. Keep the inverter away the sunlight direct
shining.
3.Ventilating,keep the around no obstruct, To ensure the air flow is free. Don't put something on the
inverter when the inver ter is working. The fan of inver ter is used to help diffuse heat.
4.To order safe, Don't used the inver ter near by the combustible material. and the place that
gathering the inflammable gas.
5.The batter y is not only supply the 11V up to the 15V direct current power, but also supply the
enough load driven current. the power should be a filled and good battery. In order to estimate a
loading current ,The loading power could be divided by the number 10.
The inver ter will be damaged when continue and frequence used the
inver ter.Don't ope n the inverter housing unless the profes sion person.
Notice
The pure sine wave inverter figure of the front face
plateand the black plate.
Only refer to the product face plate, Please refer to the actually product
The installed and connected steps:
(please refer to the right connect figure)
12V Connect figure
12V
Battery
12V
Batter y
12V
Batter y
24V-36V-48V-72V
Connect figure
Notice
Notice
6
7
6
7
8
6 7
8 8
8
5
Pure sine wave form:
Performance introduction:
The used environment:
More of electric tool and home electric appliance and audio video equipment that their rated
current and power is at the range of the inverter rated power or less more than it's.But these
equipment would show the overload protection situation when starting these equipment. The
inverter is easy driven when the load is resistance load and switch load. Because the resistance
load is line load ,It could run with full load. For example the electric stove, the electric Rice cooker,
LCD TV, etc. Equipment. Some of the audio video equipment and electric tools need be driven by
more bigger power, which it is bigger than the resistance load. Asynchronous motor, CRT TV sets,
compressors, pumps, etc. They need the 2 up to 6 times working current. so If these especial load
can run, depend on the test.
The rated current and practical equipment:
Read the information carefully about the big power tool .Ensuring the input power is accuracy.
The output power is enough for driven the tool and microwave. Please remember that the electric
tool need 2 up to 6 times power demand.
The frequently asked questions:
Don't start the electric tool and microwave stove.
The television disturb:
It is ver y smaller that the inverter disturb to the signal of TV. Nevertheless at some certain
situation ,the disturb to the TV will happen .especially the signal of TV is weak.
Please deal with problem by the follow as ways:
1. Keep the inverter away the TV antenna or extend the length of the TV antenna cable;
2. Adjust the putting direction of the inverter.
3. Ensure the strength of the TV signal is enough, which the TV antenna provide the TV. and to use
the good effect's shield cable for the TV antenna.
4. Don't used high power electric equipment and tool when you watch the TV.
5. Don't eliminate the total disturb of the old type TV
Notice
At the normal situation, the fuse will be not ruined. unless happen the
serious circuit problem. Don't repair the inverter by yourself when the
fault of inverter is happen. Please contact with the profession technology
person to dell with the fault. Because of the high voltage in the machine.
there is danger of touch the electric.
1. The first ,turn off the power of inverter electric switch.
2. Connecting the negative of battery with the black DC cable to the black post of inverter.
3. Connecting the Positive of battery with the red DC cable to the red post of inverter.
4. Plug the power of electric equipment to the output socket of inverter.
5. Used the inverter when turn on the inverter electric switch.
1. At first,turn off the inverter electric switch.
2. Pull out the power plug of load.
3. Uninstall the red DC cable
4. Uninstall the black DC cable
Uninstall steps:
Remote control diagram of inverter connection:
The battery post
position is not same
because of the different
type inverter, Please
refer to the reality
product.
1.T he connect figure is only basic refer. Please connect with the profession technique
person for actually install. The inverter is used one battery or more battery. But it is
the best to use 100AH or the battery capacity is more bigger.
The installing and using way:
2. Because of these operation need connect the battery. Ensure whether there are some
flammable gas.
Using the supply cable with the inverter(no including the model of big power cable)connect the
inverter with the battery. the red cable is connect to the red post of the input of inverter and the
negative of battery. the black cable is connect to the black post of the input of inverter and the
negative of battery. Ensure, whether the all of connect line is stable and reliable .The cable will be
damaged if the connect isn't suitable, including the over heat of cable , the post and ear line is
harmed. It is also reduce the time of supply the electric. The green lump wil be lighten when turn
the inverter power on, If the capacity is full about your battery. If the red lump will be lighten, the
inverter is protection. Solve these problem, before used it.(check the voltage if it is higher or
lower. and the output is whether it is over load or short circuit.
3.T he inverter must be connect the same value voltage of battery. the 12V inverter connect the
12V battery.24V inverter connect the 24V battery.
4. Ensure all of the equipment power is shutted down. Before insert your electric equipment plug
to the electric power. Turn on inverter model switch, the green LED lump will lighten, then you can
turn on your equipment one by one. Now your equipment can normally run if your equipment is
over load. Need reduce the load if the lump is shown the red. then you start the equipment again.
1.The suitable cable should be used when install the connected cable. For example the output
cable is too long or the conductor line Traverse area is too small,It will happen the power
consumption on the cable. the show is that the power is small and the voltage is low at the load end.
2.IF the connect cable of the battery and inverter that it is not standardize. the cable is too long,
traverse area is too small, the touch place is poor, it will happen an large of power consuming .It is
show that the power is insufficient. the battery voltage is low, the working time is short. Even the
equipment don't work as start the equipment. At the same time the cable should be prevented the
water. The insulation strengthen should be meet the required of the used environment.
BEP300SA/BEP500SA face platefigure.
BEP1000SA face platefigure.
BEP800S / 1500S / 2000S / 3000S face platefigure.
BEP5000S face platefigure.
1. Power switch
2. The socket of multifunctional AC output
3. The lamp of power shown
4. The lamp of status shown
5. The interface of output USB
6. The positive pole of battery post
7,The post of battery negative
8.The intelligence fan
9.The monitor of input voltage
10.The monitor of output voltage
11.Two color status shown lamp
12.The AC output interface
13.Remote control interface
1
2
8
11
6
7
8 8
5
2
2
1
11
5
5
10
10
9
9
2
2
2
2
1111
1111
13
1
1
2
2
12
/
