Ronbow Essentials DT5025-W4 Installation guide

DT5025-W4
Brand
Ronbow Essentials
Model
DT5025-W4
Type
Installation guide

This manual is also suitable for

VITREOUS CHINA VANITY TOP
REV. 160801
PRODUCT INSTALLATION
1
A RONBOW COMPANY
VANITY TOP
PRE-INSTALLATION
Tools Required
Safety
goggles
Silicone
Compound
WHAT IS COVERED
All products in the package carry a One-Year warranty. This warranty applies only to the original purchaser and to the
original installation of the product.
WHAT IS NOT COVERED
Damage caused during moving or during installation is not a defect or warranty issue and will not be considered as such.
This warranty does not cover product failure caused by abusive treatment, surface scratches, misuse, neglect or damage
due to handling or faulty installations. All wood naturally ages, darkens, changes in color, and mellows over time due
to exposure to light. While this color change is imperceptible from day to day, it may be signicant over a long period of
time, or due to amount of light the wood is exposed to. Imperfections such as small surface splits, small dark holes or
darker mineral streaks are natural and are not considered defects.
Toll free Customer Assistance at 877.659.2128
M - F: 7:30AM - 4:30PM PST.
LIMITED WARRANTY
MODEL: DT5025
DT5031
DT5037
DT5049
Package Contents
A
Part Description Quantity
A Vitreous china vanity top 1
PRE-INSTALLATION (continued)
VITREOUS CHINA VANITY TOP
REV. 160801
PRODUCT INSTALLATION
2
A RONBOW COMPANY
INSTALLATION
1
Vanity top preparation
□ Install the faucet into the pre-drilled locations of the
vanity top (Faucet and Drain not included).
□ Follow the manufactures installation instructions to
install the faucet and drain.
□ Do not over tighten the faucet system to avoid
unnecessary damage to the vanity top.
2
Vanity preparation
□ The vanity should be set in place per the
manufactures installation instructions (Vanity not
included).
□ Use a light damp cloth to wipe any dirt or dust from
the top edge of the vanity.
VITREOUS CHINA VANITY TOP
REV. 160801
PRODUCT INSTALLATION
3
A RONBOW COMPANY
INSTALLATION (continued)
3
Installing the vanity top
It is highly recommended to have a second person for this
step.
□ Apply a small bead of silicone compound to the top
edge of the vanity. The silicone compound will act
as an adhesive to secure the top to the vanity.
□ Carry the vanity top to the vanity location and set
the top in place.
□ Always carry this product vertically to avoid excess
stress to the vanity top.
□ Place the vanity top into the nal position as close
as possible. Avoid moving the top excessively after
setting into place.
□ Clean up any excess silicone compound with a
clean damp rag.
cabinet
4
Drying time
□ Allow at least 24 hours for the silicone to fully dry.
Refer to the silicone tube for instructions.
□ During this time avoid moving the vanity top.
DISCLAIMER
These instructions are for reference only. Due to the variety of installation situations, Aravo assumes no responsibility
for installation procedures, or damage to the products during installation. Aravo believes the average consumer can
install the product, but we recommend you consult with a professional. Proper safety and care should be taken during
installation to avoid injury.
CARE AND CLEANING
VITREOUS CHINA
Vitreous china vanity tops and sinks are very durable. The glazing process provides years of enjoyment if cared for
correctly. Rinse thoroughly and use a soft cloth to wipe the product dry after each use to prevent hard water stains. Soft
abrasive cleaners may be used when necessary to clean vitreous china products.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Ronbow Essentials DT5025-W4 Installation guide

DT5025-W4
Brand
Ronbow Essentials
Model
DT5025-W4
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents