Fujitsu ASUB24TLAV1 Installation guide

ASUB24TLAV1
Fujitsu
Brand
Fujitsu
Model
ASUB24TLAV1
Category
Split-system air conditioners
Type
Installation guide

This manual is also suitable for

English
INSTALLATION MANUAL
INDOOR UNIT (Wall Mounted Type)
For authorized service personnel only.
ASUB18TLAV1
ASUB24TLAV1
TM
FrançaisEspañol
MANUEL D’INSTALLATION
MANUAL DE INSTALACIÓN
UNITÉ INTÉRIEURE (Type montage mural)
UNIDAD INTERIOR (Tipo montado en pared)
Pour le personnel agréé uniquement.
Únicamente para personal de servicio autorizado.
PART No. 9373370444
En-1
1. SAFETY PRECAUTIONS
1.1. IMPORTANT! Please read before starting
This air conditioning system meets strict safety and operating standards.
As the installer or service person, it is an important part of your job to install or service the
system so it operates safely and efficiently.
For safe installation and trouble-free operation, you must:
• Carefully read this instruction booklet before beginning.
• Follow each installation or repair step exactly as shown.
• Observe all local, state, and national electrical codes.
• Pay close attention to all danger, warning, and caution notices given in this manual.
WARNING:
This symbol refers to a hazard or unsafe practice which can result in
severe personal injury or death.
CAUTION:
This symbol refers to a hazard or unsafe practice which can result in
personal injury and the potential for product or property damage.
• Hazard alerting symbols
: Electrical : Safety/alert
If Necessary, Get Help
These instructions are all you need for most installation sites and maintenance conditions.
If you require help for a special problem, contact our sales/service outlet or your certified
dealer for additional instructions.
In Case of Improper Installation
The manufacturer shall in no way be responsible for improper installation or maintenance
service, including failure to follow the instructions in this document.
1.2. SPECIAL PRECAUTIONS
When Wiring
ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH. ONLY A
QUALIFIED, EXPERIENCED ELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM.
• Do not supply power to the unit until all wiring and tubing are completed or reconnected
and checked.
• Highly dangerous electrical voltages are used in this system. Carefully refer to the wir-
ing diagram and these instructions when wiring. Improper connections and inadequate
earthing (grounding) can cause accidental injury or death.
• Earth (Ground) the unit following local electrical codes.
• Connect all wiring tightly. Loose wiring may cause overheating at connection points and
a possible fi re hazard.
When Transporting
Be careful when picking up and moving the indoor and outdoor units. Get a partner to
help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin
aluminum fi ns on the air conditioner can cut your fi ngers.
When Installing...
...In a Ceiling or Wall
Make sure the ceiling/wall is strong enough to hold the unit’s weight. It may be necessary
to construct a strong wood or metal frame to provide added support.
...In a Room
Properly insulate any tubing run inside a room to prevent “sweating” that can cause
dripping and water damage to walls and fl oors.
...In an Area with High Winds
Securely anchor the outdoor unit down with bolts and a metal frame.
Provide a suitable air baffl e.
...In a Snowy Area (for Heat Pump-type Systems)
Install the outdoor unit on a raised platform that is higher than drifting snow.
When Connecting Refrigerant Tubing
• Keep all tubing runs as short as possible.
• Use the fl are method for connecting tubing.
• Apply refrigerant lubricant to the matching surfaces of the fl are and union tubes before
connecting them, then tighten the nut with a torque wrench for a leak-free connection.
• Check carefully for leaks before opening the refrigerant valves.
When Servicing
• Turn the power OFF at the main circuit breaker panel before opening the unit to check or
repair electrical parts and wiring.
• Keep your fi ngers and clothing away from any moving parts.
• Clean up the site after you fi nish, remembering to check that no metal scraps or bits of
wiring have been left inside the unit being serviced.
• After installation, explain correct operation to the customer, using the operating manual.
DANGER
Never touch electrical components immediately after the power supply has been turned
off. Electrical shock may occur. After turning off the power, always wait 5 minutes or more
before touching electrical components.
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information
pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual to the customer.
• Request the customer to keep them on hand for future use, such as for relocating or
repairing the unit.
WARNING
Request your dealer or a professional installer to install the unit in accordance with this
Manual.
An improperly installed unit can cause serious accidents such as water leakage, electric
shock, or fire.
If the unit is instruction in disregard of the instructions in the Installation Manual, it will
void the manufacturer’s warranty.
Do not turn ON the power until all work has been completed.
Turning ON the power before the work is completed can cause serious accidents such
as electric shock or fire.
If refrigerant leaks while work is being carried out, ventilate the area.
If the refrigerant comes in contact with a flame, it produces a toxic gas.
Installation must be performed in accordance with the requirement of NEC (National
Electrical Code) and CEC (Canadian Electrical Code) by authorized personnel only.
Except for EMERGENCY, never turn off main as well as sub breaker of the indoor units
during operation. It will cause compressor failure as well as water leakage. First, stop
the indoor unit by operating the control unit, converter or external input device and then
cut the breaker.
Make sure to operate through the control unit, converter or external input device.
When the breaker is designed, locate it at a place where the users cannot start and stop
in the daily work.
INSTALLATION MANUAL
PART No. 9373370444
VRF system indoor unit (Wall mounted type)
Contents
1. SAFETY PRECAUTIONS ........................................................................................... 1
1.1. IMPORTANT! Please read before starting ........................................................... 1
1.2. SPECIAL PRECAUTIONS ................................................................................... 1
2. ABOUT THIS PRODUCT ............................................................................................ 2
2.1. Precautions for using R410A refrigerant .............................................................. 2
2.2. Special tools for R410A .......................................................................................2
2.3. Accessories ......................................................................................................... 2
2.4. Optional parts ...................................................................................................... 2
2.5. About unit of the length ........................................................................................ 2
3. INSTALLATION WORK .............................................................................................. 3
3.1. Selecting an installation location .......................................................................... 3
3.2. Installation dimension .......................................................................................... 3
3.3. Installing the unit .................................................................................................. 3
4. PIPE INSTALLATION .................................................................................................. 4
4.1. Selecting the pipe material .................................................................................. 4
4.2. Pipe requirement ................................................................................................. 5
4.3. Flare connection (pipe connection) ...................................................................... 5
5. FORMING THE DRAIN HOSE AND PIPE .................................................................. 5
6. ELECTRICAL WIRING ................................................................................................ 6
6.1. Electrical requirement .......................................................................................... 7
6.2. Wiring method ...................................................................................................... 7
6.3. Unit wiring ............................................................................................................ 7
6.4. Wiring ................................................................................................................... 9
6.5. Optional parts wiring ............................................................................................ 9
6.6. External input and external output (Optional parts) ............................................. 9
7. FIELD SETTING ........................................................................................................ 11
7.1. Setting the address ............................................................................................ 11
7.2. Custom code setting .......................................................................................... 12
7.3. Function setting ................................................................................................. 13
8. FINISHING................................................................................................................. 14
8.1. Connection pipe, cable and drain hose .............................................................14
8.2. Installing front cover ........................................................................................... 15
9. TEST RUN ................................................................................................................. 15
9.1. Test run using Outdoor unit (PCB) ..................................................................... 15
9.2. Test run using remote controller ........................................................................ 15
10. CHECK LIST ............................................................................................................. 15
11. ERROR CODES ........................................................................................................ 16
En-2
2. ABOUT THIS PRODUCT
2.1. Precautions for using R410A refrigerant
WARNING
Do not introduce any substance other than the prescribed refrigerant into the
refrigeration cycle. If air enters the refrigeration cycle, the pressure in the refrigeration
cycle will become abnormally high and cause the piping to rupture.
If there is a refrigerant leak, make sure that it does not exceed the concentration limit.
If a refrigerant leak exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
area. Touching the refrigerant directly can cause frostbite.
If a refrigerant leak occurs during operation, immediately vacate the premises and
thoroughly ventilate the area. If the refrigerant comes in contact with a flame, it
produces a toxic gas.
2.2. Special tools for R410A
WARNING
To install a unit that uses R410A refrigerant, use dedicated tools and piping materials
that have been manufactured specifically for R410A use. Because the pressure
of R410A refrigerant is approximately 1.6 times higher than the R22, failure to
use dedicated piping material or improper installation can cause rupture or injury.
Furthermore, it can cause serious accidents such as water leakage, electric shock, or
fi re.
Tool name Contents of change for R22 tool
Gauge manifold
Pressure is huge and cannot be measured with a conventional
(R22) gauge. To prevent erroneous mixing of other refrigerants,
the diameter of each port has been changed.
It is recommended to use a gauge manifold with a high pressure
display range 30 in Hg to 768 psi (–0.1 to 5.3 MPa) and a low
pressure display range 30 in Hg to 551 psi (–0.1 to 3.8 MPa).
Charging hose
To increase pressure resistance, the hose material and base size
were changed.
Vacuum pump
A conventional (R22) vacuum pump can be used by installing a
vacuum pump adapter.
• A conventional vacuum pump can be used by installing a
vacuum pump adapter.
• Be sure that the pump oil does not back flow into the system.
Use one capable for vacuum suction of 5 Torr, –755 mm Hg
(–100.7 kPa).
Gas leakage
detector
Special gas leakage detector for HFC refrigerant R410A.
2.3. Accessories
WARNING
For installation purposes, be sure to use the parts supplied by the manufacturer or other
prescribed parts.
The use of non-prescribed parts can cause serious accidents such as the unit falling, water
leakage, electric shock, or fi re.
• The following installation parts are furnished. Use them as required.
• Keep the Installation Manual in a safe place and do not discard any other accessories
until the installation work has been completed.
Name and Shape Q’ty Application
Operating Manual
1
Installation Manual
1
(This book)
Wall hook bracket
1
For indoor unit installation
Cloth tape
1
For indoor unit installation
Name and Shape Q’ty Application
Tapping screw (Big)
(M4 × 25mm)
8
For wall hook bracket installation
Air cleaning fi lter
2
For installation, refer to the “CLEAN-
ING AND CARE” in the operating
manual.
Air cleaning fi lter frame
2
Drain hose Insulation
1
For installing drain hose
Connecting cable
1
For wired remote controller cable
connected
Cable tie
1
For transmission and remote con-
troller cable binding
2.4. Optional parts
Description Model Application
External connect kit
UTY-XWZXZC
For output function
(Output terminal / CNB01)
UTY-XWZXZB
For control input function
(Apply voltage terminal / CNA01)
UTY-XWZXZD
For control input function
(Dry contact terminal / CNA02)
UTY-XWZXZ7
For forced thermostat off function
(Apply voltage terminal / CNA03)
UTY-XWZXZE
For forced thermostat off function
(Dry contact terminal / CNA04)
2.5. About unit of the length
All Fujitsu General products are manufactured to metric units and tolerances. United
States customary units are provided for reference only. In cases where exact dimensions
and tolerances are required, always refer to metric units.
En-3
3. INSTALLATION WORK
Correct initial installation location is important because it is difficult to move unit after it is
installed.
3.1. Selecting an installation location
Decide the mounting position together with the customer as follows.
WARNING
Select installation locations that can properly support the weight of the indoor unit.
Install the units securely so that they do not topple or fall.
CAUTION
Do not install the indoor unit in the following areas:
• Area with high salt content, such as at the seaside. It will deteriorate metal parts, caus-
ing the parts to fail or the unit to leak water.
• Area filled with mineral oil or containing a large amount of splashed oil or steam, such
as a kitchen. It will deteriorate plastic parts, causing the parts to fail or the unit to leak
water.
• Area that generates substances that adversely affect the equipment, such as sulfuric
gas, chlorine gas, acid, or alkali. It will cause the copper pipes and brazed joints to
corrode, which can cause refrigerant leakage.
• Area that can cause combustible gas to leak, contains suspended carbon fibers or
flammable dust, or volatile inflammables such as paint thinner or gasoline. If gas leaks
and settles around the unit, it can cause a fire.
• Area where animals may urinate on the unit or ammonia may be generated.
Do not use the unit for special purposes, such as storing food, raising animals, growing
plants, or preserving precision devices or art objects.
It can degrade the quality of the preserved or stored objects.
Do not install where there is the danger of combustible gas leakage.
Do not install the unit near a source of heat, steam, or flammable gas.
Install the unit where drainage does not cause any trouble.
Install the indoor unit, power supply cable, transmission cable, and remote controller
cable at least 40 in (1 m) away from a television or radio receivers. The purpose of this
is to prevent TV reception interference or radio noise. (Even if they are installed more
than 40 in (1 m) apart, you could still receive noise under some signal conditions.)
If children under 10 years old may approach the unit, take preventive measures so that
they cannot reach the unit.
Take precautions to prevent the unit from falling.
(1) Install the indoor unit on a place having a sufficient strength so that it withstands
against the weight of the indoor unit.
(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all
over the room.
(3) Leave the space required to service the air conditioner.
(4) Install the unit where connection to the outdoor unit (or RB unit) is easy.
(5) Install the unit where the connection pipe can be easily installed.
(6) Install the unit where the drain pipe can be easily installed.
(7) Install the unit where noise and vibrations are not amplified.
(8) Take servicing, etc., into consideration and leave the spaces. Also install the unit
where the filter can be removed.
(9) Do not install the unit where it will be exposed to direct sunlight.
3.2. Installation dimension
For the drain hose exten-
sion, use a drain hose
with a 5/8 in (16 mm)
inside diameter.
71 in (1800
mm) or more
60 in (1500
mm) or
more
Right side 8
in (200 mm)
or more
3 in (60 mm) or more
Left side 2
in (50 mm)
or more
Wall hook bracket
3.3. Installing the unit
WARNING
Install the air conditioner in a location which can withstand a load of at least 5 times the
weight of the main unit and which will not amplify sound or vibration. If the installation
location is not strong enough, the indoor unit may fall and cause injuries.
The piping can be connected in the 7 directions indicated by
1
,
2
,
3
,
4
,
5
,
6
and
7
5
Left piping
2
Right
piping
3
Bottom piping
6
Center piping
4
Left bottom piping
7
Left rear piping
1
Rear piping
3.3.1. Installing the wall hook bracket
WARNING
If the wall pipe is not used, the cable interconnecting the indoor and outdoor units may
touch metal and cause electric leakage.
[Installation directly to a wall]
Refer to Fig. A for the installation hole dimensions of the wall hook bracket.
Before fastening the wall hook bracket to the wall with the screws, level it by tapping the
hook at the center of bracket to the wall with the handle of a screwdriver.
(1) Fasten the wall hook bracket to the wall with 6 or more screws and anchor bolts
through the holes near the outer edge of the bracket.
(Do not install the wall hook bracket at only 1 place or at an angle.)
(2) For a concrete wall, embed anchor bolts (3/8 in (10 mm) dia.) into the wall at the wall
hook bracket holes.
(Allow the anchor bolts to stick out at least 11/16 in (18 mm) from the wall. Use 2
bolts for flat concrete wall and 4 bolts for blister concrete wall.)
(3) Install the nuts to the anchor bolts through the wall hook bracket.
(4) Finally tighten the bolts and wood screws after confirming, using the level indicator,
that the clamp is horizontal.
WARNING
Install the wall hook bracket level, both horizontally and vertically. If the wall hook
bracket is tilted, wa ter will drip to the floor.
As the weight of the indoor unit is 33 to 40 lbs (15 to 18 kg), it should be installed after
properly examining the place where it is in tended to be in stalled. If the place is not
strong enough, a plank or girder should be used to make the place sufficiently strong so
that the wall can support the weight.
Fig. A
17-5/16 (439)
4-13/16
(122)
2-15/16
(
75
)
2-15/16
(75)
1-7/16
(37)
Ø 3-1/8
(80)
Ø 2-9/16 (65)
Ø 3-1/8 (80)
17-1/4 (438) 15-5/8 (397)
39-5/16 (998)
6-11/16
(170)
5-1/8
(130)
1 × 7/16
(26 × 11)
1 × 7/16
(26 × 11)
11/16 × 7/16
(18 × 11)
11/16 × 7/16
(18 × 11)
13/16 × 3/16
(21 × 5)
3/16 × 11/16
(5 × 18)
3/16 × 1-15/16
(5 × 50)
1/2 × 3/16
(13 × 5)
6-3/4
(172)
5-1/4
(133)
4-15/16
(
126
)
13/16 (20)
15-1/4 (387)5/8 (16)
15-3/4 (400)
9-9/16 (243) 4-7/16 (113)
1/2 (12)
1/2 (12)
10-9/16 (269)
12-5/8 (320)
1-3/4 (44)
1/2 (13)
15-7/8 (149)
7-3/4 (197)
1-3/16 (30)
10-11/16 (272)
Unit: [in (mm)]
UNIT center
hole for tapping screw
Outline of Unit
Piping inlet
hole
hole
hole (14 places)
hole (4 places)hole (3 places)
(UNIT size)
Piping inlet
(UNIT size)
hole (14 places)
hole
hole
En-4
[For
1
Rear piping,
2
Right piping and
3
Bottom piping]
• The drain hose and drain cap are used as they are.
[For
4
Left bottom piping,
5
Left piping and
6
Center piping,
7
Left rear
piping]
• Remove the drain cap and drain hose. Mount the drain cap and drain hose to the drain
port on its opposite side.
Left side
Right side
Drain cap
Drain hose
Drain cap
Drain hose
Insert the drain hose until it butts
against the drain port.
Insert the drain cap until it butts
against the drain port.
3.3.4. Cut-out for piping on front cover
[For
2
Right piping,
3
Bottom piping,
4
Left bottom piping and
5
Left pip-
ing]
• Use a metal shears or other cutting tool to cut along the groove in the plastic for the
piping that will coming out of the front cover.
For
2
Right piping
For
5
Left piping
For
4
Left bottom piping
For
3
Bottom piping
4. PIPE INSTALLATION
CAUTION
Be more careful that foreign matter (oil, water, etc.) does not enter the piping than with
refrigerant R410A models. Also, when storing the piping, securely seal the openings by
pinching, taping, etc.
While welding the pipes, be sure to blow dry nitrogen gas through them.
4.1. Selecting the pipe material
CAUTION
Do not use existing pipes from another refrigeration system or refrigerant.
Use pipes that have clean external and internal sides without any contamination which
may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or water.
It is necessary to use seamless copper pipes.
Material : Phosphor deoxidized seamless copper pipes
It is desirable that the amount of residual oil is less than 0.04 oz/100 ft (40 mg/10 m).
Do not use copper pipes that have a collapsed, deformed, or discolored portion (es-
pecially on the interior surface). Otherwise, the expansion valve or capillary tube may
become blocked with contaminants.
Improper pipe selection will degrade performance. As an air conditioner using R410A
incurs pressure higher than when using conventional (R22) refrigerant, it is necessary to
choose adequate materials.
• Thicknesses of copper pipes used with R410A are as shown in the table.
• Never use copper pipes thinner than those indicated in the table even if they are avail-
able on the market.
Wall hook bracket
Tapping screw (big)
3.3.2. Cutting the hole in the wall for the connecting piping
WARNING
If the wall pipe is not used, the cable may touch metal and cause electric leakage.
(1) Cut a 3-1/8 in (80 mm) diameter hole in the wall at the position shown in Fig. B.
(2) For
1
Rear piping and
7
Left rear piping, cut the hole to a point of intersection of
center marks (Fig. B).
For
2
Right piping and
5
Left piping, cut the hole at least 3/8 in (10 mm) below the
holes for the rear piping and left rear piping for the drain water to fl ow freely (Fig. B).
For
6
Center piping, cut a hole in the lower, center section of the wall hook bracket.
(Refer to Fig. A. Do not cut a hole outside of the indoor unit outline.)
(3) Cut the hole so that the outside end is lower 3/16 to 3/8 in (5 to 10 mm) than the
inside end.
(4) Always align the center of the wall hole. If misaligned, water leakage will occur.
(5) Cut the wall pipe to match the wall thickness, stick it into the wall cap fasten with
vinyl tape, and stick the pipe through the hole.(The connection pipe is supplied in the
installation set.)
(6) For left piping and right piping and center piping, cut the hole a little lower so that
drain water will fl ow freely.
Fig. B
3-1/8 in
80 mm
dia. hole
(For
2
Right pip-
ing)
Lower
3-1/8 in
(80 mm)
dia. hole
Center mark
Lower
3/8 in
(10 mm)
or more
(For
5
Left pip-
ing)
(For
1
Rear
piping)
(For
7
Left rear
piping)
3/8 in
(10 mm)
or more
Wall hook bracket
Fasten with
vinyl tape
Wall cap*
Wall pipe*
(Inside) Wall (Outside)
*Locally purchased
3/16 to 3/8 in
(5 to 10 mm) low
3.3.3. Attach the drain hose
CAUTION
Insert the drain hose and drain cap into the drain port, making sure that it comes in con-
tact with the back of the drain port, and then mount it. If the drain hose is not connected
properly, leaking will occur.
• Wrap the insulation around the drain hose, making sure that there are no gaps.
• Attach the Insulation (Drain hose) to the drain hose.
Drain hose
Insulation (Drain hose)
(Accessories)
En-5
Thicknesses of Annealed Copper Pipes (R410A)
Pipe outside diameter [in (mm)] Thickness [in (mm)]
1/4 (6.35) 0.032 (0.80)
3/8 (9.52) 0.032 (0.80)
1/2 (12.70) 0.032 (0.80)
5/8 (15.88) 0.039 (1.00)
3/4 (19.05) 0.039 (1.20)
4.2. Pipe requirement
CAUTION
Refer to the installation manual for the outdoor unit for description of allowable pipe
length and height difference.
Use pipe with water-resistant heat insulation.
CAUTION
Install heat insulation around both the gas and liquid pipes. Failure to do so may cause
water leaks.
Use heat insulation with heat resistance above 248 °F (120 °C). (Reverse cycle model
only)
In addition, if the humidity level at the installation location of the refrigerant piping is
expected to exceed 70 %, install heat insulation around the refrigerant piping. If the
expected humidity level is 70 to 80 %, use heat insulation that is 9/16 in (15 mm) or
thicker and if the expected humidity exceeds 80 %, use heat insulation that is 13/16 in
(20 mm) or thicker. If heat insulation is used that is not as thick as specified, condensa-
tion may form on the surface of the insulation. In addition, use heat insulation with heat
conductivity of 0.045 W/(m·K) or less (at 68 °F (20 °C)).
4.3. Flare connection (pipe connection)
WARNING
Tighten the flare nuts with a torque wrench using the specified tightening method. Other-
wise, the flare nuts could break after a prolonged period, causing refrigerant to leak and
generate hazardous gas if the refrigerant comes into contact with a flame.
4.3.1. Flaring
Use special fl are tool exclusive for R410A.
(1) Cut the connection pipe to the necessary length with a pipe cutter.
(2) Hold the pipe downward so that cuttings will not enter the pipe and remove any burrs.
(3) Insert the flare nut (always use the flare nut attached to the indoor and outdoor units
(or RB unit) respectively) onto the pipe and perform the flare processing with a flare
tool. Use the special R410A flare tool. Leakage of refrigerant may result if other flare
nuts are used.
(4) Protect the pipes by pinching them or with tape to prevent dust, dirt, or water from
entering the pipes.
B
A
L
Check if [L] is flared uniformly and
is not cracked or scratched.
Pipe
Die
Pipe outside diameter
[in (mm)]
Dimension A [in (mm)]
Dimension B
0 (0)
-0.015 (-0.4)
[in (mm)]
Flare tool for R410A,
clutch type
1/4 (6.35)
0 to 0.020
(0 to 0.5)
3/8 (9.1)
3/8 (9.52) 1/2 (13.2)
1/2 (12.70) 5/8 (16.6)
5/8 (15.88) 3/4 (19.7)
3/4 (19.05) 15/16 (24.0)
When using conventional (R22) flare tools to flare R410A pipes, the dimension A should
be approximately 0.020 in (0.5 mm) more than indicated in the table (for flaring with
R410A flare tools) to achieve the specified flaring. Use a thickness gauge to measure the
dimension A. It is recommended that a R410A flaring tool is used.
Width across
flats
Pipe outside diameter
[in (mm)]
Width across flats of Flare
nut [in (mm)]
1/4 (6.35) 11/16 (17)
3/8 (9.52) 7/8 (22)
1/2 (12.70) 1 (26)
5/8 (15.88) 1-1/8 (29)
3/4 (19.05) 1-7/16 (36)
4.3.2. Bending pipes
• The pipes are shaped by your hands or pipe bender. Be careful not to collapse them.
• Do not bend the pipes in an angle more than 90°.
• When pipes are repeatedly bent or stretched, the material will harden, making it difficult
to bend or stretch them anymore. Do not bend or stretch the pipes more than 3 times.
CAUTION
To prevent breaking of the pipe, avoid sharp bends.
If the pipe is bent repeatedly at the same place, it will break.
4.3.3. Pipe connection
CAUTION
Be sure to install the pipe against the port on the indoor unit and the outdoor unit cor-
rectly. If the centering is improper, the flare nut cannot tightened smoothly. If the flare
nut is forced to turn, the threads will be damaged.
Do not remove the flare nut from the indoor unit pipe until immediately before connect-
ing the connection pipe.
Do not use mineral oil on flared part. Prevent mineral oil from getting into the system as
this would reduce the lifetime of the units.
Hold the torque wrench at its grip, keeping it at a right angle with the pipe, in order to
tighten the flare nut correctly.
When the flare nut is tight-
ened properly by your hand,
hold the body side coupling
with a separate spanner, then
tighten with a torque wrench.
(See the table below for the
flare nut tightening torques.)
Tighten with 2
wrenches.
Holding wrench
Flare nut
Connection pipe
Indoor unit pipe (Body side)
Torque wrench
Flare nut [in (mm)] Tightening torque [lbf·ft (N·m)]
1/4 (6.35) dia. 11.8 to 13.3 (16 to 18)
3/8 (9.52) dia. 23.6 to 31.0 (32 to 42)
1/2 (12.70) dia. 36.1 to 45.0 (49 to 61)
5/8 (15.88) dia. 46.5 to 55.3 (63 to 75)
3/4 (19.05) dia. 66.4 to 81.1 (90 to 110)
5. FORMING THE DRAIN HOSE AND PIPE
CAUTION
Do not remove the flare nut from the indoor unit pipe until immediately before
connecting the connection pipe.
To prevent breaking of the pipe, avoid sharp bends.
If the pipe is bent repeatedly at the same place, it will break.
[For
1
Rear piping,
2
Right piping and
3
Bottom piping]
• Install the indoor unit piping in the direction of the wall hole and bind the drain hose and
pipe together with vinyl tape.
• Install the piping so that the drain hose is at the bottom.
• Wrap the pipes of the indoor unit that are visible from the outside with decorative tape.
Pipe (Top)
Cloth tape
(Accessories)
2
Right piping
3
Bottom piping
Bind with vinyl tape
Drain hose (Bottom)
1
Rear piping
En-6
6. ELECTRICAL WIRING
WARNING
Electrical work must be performed in accordance with this Manual by a person certified
under the national or regional regulations. Be sure to use a dedicated circuit for the unit.
An insufficient power supply circuit or improperly performed electrical work can cause
serious accidents such as electric shock or fire.
Before starting work, check that power is not being supplied to the all units.
Use the included connection cables and power cables or ones specified by the
manufacturer. Improper connections, insufficient insulation, or exceeding the allowable
current can cause electric shock or fire.
For wiring, use the prescribed type of cables, connect them securely, making sure that
there are no external forces of the cables applied to the terminal connections. Improp-
erly connected or secured cables can cause serious accidents such as overheating the
terminals, electric shock, or fire.
Do not modify the power cables, use extension cables, or use any branches in the wir-
ing. Improper connections, insufficient insulation, or exceeding the allowable current can
cause electric shock or fire.
Match the terminal board numbers and connection cable colors with those of the out-
door unit (or RB unit). Erroneous wiring may cause burning of the electric parts.
Securely connect the connection cables to the terminal board. In addition, secure the
cables with wiring holders. Improper connections, either in the wiring or at the ends of
the wiring, can cause a malfunction, electric shock, or fire.
Always fasten the outside covering of the connection cable with the cable clamp. (If the
insulator is chafed, electric discharge may occur.)
Securely install the electrical box cover on the unit. An improperly installed electrical box
cover can cause serious accidents such as electric shock or fire through exposure to
dust or water.
Install sleeves into any holes made in the walls for wiring. Otherwise, a short circuit
could result.
We suggest installing GFEB breakers or follow local electrical code. When installing
this system, install using ground fault equipment breakers (GFEB) to reduce the risk of
leaking current which result in electric shock or potential fire.
Always connect the earth (ground) cable.
Improper earthing (grounding) work can cause electric shocks.
Install the remote controller cables so as not to be direct touched with your hand.
Perform wiring work in accordance with standards so that the air conditioner can be
operated safely and positively.
Connect the connection cable firmly to the terminal board. Imperfect installation may
cause a fire.
If the supply cable is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
CAUTION
Earth (Ground) the unit.
Do not connect the earth (ground) cable to a gas pipe, water pipe, lightning rod, or a
telephone earth (ground) cable.
Improper earthing (grounding) may cause electric shock.
Do not connect power supply cable to the transmission or remote controller terminals,
as this will damage the product.
Never bundle the power supply cable and transmission cable, remote controller cable
together.
Separate these cable by 2 in (50 mm) or more.
Bundling these cables together will cause miss operation or breakdown.
When handling PCB, static electricity charged in the body may cause malfunction of the
PCB. Follow the cautions below:
• Establish an earth (ground) for the indoor and outdoor units and peripheral devices.
• Cut power (breaker) off.
• Touch metal part of the indoor units for more than 10 seconds to discharge static
electricity charged in the body.
• Do not touch terminals of parts and patterns implemented on PCB.
CAUTION
Do not wrap the tape too tightly on drain hose. If the tape is too tight (as shown in the
Figure below) the insulation effect will be lost and the moisture from condensation
may accumulate.
Bad Example
Vinyl tape too tight
• Perform “6. ELECTRICAL WIRING” before performing this piping.
• Wrap the pipes of the indoor unit that are visible from the outside with cloth tape.
• After passing the indoor piping and drain hose through the wall hole, hang the indoor
unit on the hooks at the top of the wall hook bracket.
[For
4
Left bottom piping,
5
Left piping and
6
Center piping,
7
Left rear
piping]
• Preset the end of the pipe.
•
For
6
Center piping and,
7
Left rear piping route the connection pipes through the wall.
• Bend the connection piping to a bend radius not less than 3-15/16 in (100 mm) and
position the piping no more than 1-3/8 in (35 mm) from the wall.
• After passing the indoor unit piping and drain hose through the wall hole, hang the
indoor unit on the hooks at the top and bottom of the wall hook bracket.
Wall
hook
bracket
Small piping (Liquid pipe)
Large piping (Gas pipe)
Connection piping
Alignment marks
[
Hang the indoor unit
]
• Hang the indoor unit from the hooks at the top of the wall hook bracket.
• Insert the spacer, etc. between the indoor unit and the wall hook bracket and separate
the bottom of the indoor unit from the wall.
Bottom hook
Indoor unit
Top hooks
Wall hook bracket
Indoor unit
Spacer
En-7
6.1. Electrical requirement
• Select the power cable type and size
in accordance with relevant local and
national regulations.
Voltage rating
208/230 V
Operating range
187 to 253 V
• Specifications for local wiring power cord and branch wiring are in compliance with local
code
• Max. wire length: Set a length so that the voltage drop is less than 2%. Increase the wire
diameter when the wire length is long.
Breaker should be installed at every refrigerant system. Do not use a breaker in a different
refrigerant system.
Refer to the table for the breaker specifications of each installation condition. Perform
the power crossover wiring within the range of the same refrigerant system. When the
crossover wiring is done, make a connection for indoor units to satisfy conditions A and B
below.
A. Current breaker requirements
Model MCA
MAX. CKT. BKR
(Fuse capacity)
• MCA: Minimum Circuit Ampacity
• MAX. CKT. BKR : Maximum Circuit
Breaker
ASUB18TLAV1 0.53 A
15 A
ASUB24TLAV1 0.65 A
When the power crossover wiring is done, make it so that the total of the MCA of the con-
nected RB units and indoor units does not exceed the 11 A. For RB unit MCA, refer to the
RB unit installation manual.
If the capacity of connected RB units and indoor units exceeds the upper limit, either add
breakers or use a breaker with a greater capacity.
B. Earth leakage breaker requirements
Breaker capacity
Maximum connect-
able “indoor units”
or “indoor units +
RB units” (*1)
*1: Heat pump type: indoor units,
Heat recovery type: indoor units
and RB units.
*2: If the 100 mA capacity breaker is
not provided, split the quantity of
the indoor units into small groups
of 9 units or less and provide a
breaker with capacity of 30 mA for
each group.
30 mA, 0.1 sec or less 36 or less
100 mA, 0.1 sec or less 37 to 121 (*2)
6.1.1 Cable specifi cations
Cable size Cable type Remarks
Transmission
cable
22 AWG
(0.33 mm²)
LEVEL 4 (NEMA) non-polar
2 core, twisted pair solid core
diameter 0.026 in (0.65mm)
LONWORKS ®
compatible cable
Remote con-
troller cable
(2-wire type)
22 AWG to 16 AWG
(0.33 to 1.25 mm²)
Sheathed PVC cable
Non polar 2 core,
twisted pair
18AWG Thermostat cable 2 core
Use sheathed non
twisted pair cable
Remote con-
troller cable
(3-wire type)
22 AWG
(0.33 mm²)
Sheathed PVC cable Polar 3 core
6.2. Wiring method
Example
*2
*2
*2
Outdoor unit or RB unit *1
Breaker 1: Ground Fault Equipment
Breaker (GFEB)
Breaker 2: Maximum Circuit Breaker
(MAX. CKT. BKR)
Transmission
Transmission
Indoor unit
Remote controller
(Master)
Power supply
Indoor unit Indoor unit
Power supply
Remote
control
Breaker 2
Breaker 2
Breaker 2
Breaker 1
Breaker 1
Breaker 1
Remote controller
(Slave)
Remote
controller
*1: When connecting to the Heat Recovery System, refer to the installation manual of the
RB unit.
*2: Earth (Ground) the remote controller if it has an earth (ground) cable.
*3: When connecting the 2-wire type remote controller, Y3 is not used.
(Crossover wiring of power supply)
Indoor unit
Pull box
Pull box
Power supply Power supply Power supply
Indoor unit Indoor unit
Breaker 2
Breaker 1
Power supply
: Disconnect switch
6.3. Unit wiring
• Before attaching the cable to terminal block.
6.3.1. Power supply cable
6-7/8 in (175 mm)
6-1/2 in (165 mm)
Conduit connector
Conduit holder
Earth
(ground) cable
A.
For solid core wiring
(1) To connect the electrical terminal, follow the below diagram and connect after looping
it around the end of the cable.
(2) Use the specifi ed cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(3) Use an appropriate screwdriver to tighten the terminal screws.
Do not use a screwdriver that is too small, otherwise, the screw heads may be dam-
aged and prevent the screws from being properly tightened.
(4) Do not tighten the terminal screws too much, otherwise, the screws may break.
(5) See the table for the terminal screw tightening torques.
(6) Please do not fi x 2 power supply cables with 1 screw.
Strip 1 in
(25 mm)
Screw with
special washer
Screw with
special washer
Cable end (Loop)
Loop
Terminal block
Cable end (Loop)
Cable
Cable
En-8
6.3.3. Remote controller cable
Remote controller cable modifi cation.
(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then
remove the insulation from the cut end of the cable.
13/16 in (20 mm)
13/16 in (20 mm)
For 3-wire typeFor 2-wire type
(2) Connect the remote controller cable with connecting cable with solder.
IMPORTANT:
Be sure to insulate the connection between the cables.
For dual control or group control
For 3-wire type
Solder and insulate the connected parts.
Red
Red
White
Black
Remote controller cable
Connecting cable
(Accessories)
Black
White
For 2-wire type
Solder and insulate the connected parts.
Red
Connecting cable
(Accessories)
Remote controller
cable (non polar)
Cut and insulate
Black
White
(3) Connect the cable of wired remote controller unit to the connector of control unit, and
set the DIP switch (SW1).
CAUTION
When switching the DIP switch (SW1), be sure to turn off the power supply to the
indoor unit. Otherwise, the PC board of the indoor unit may be damaged.
For 2-wire type For 3-wire type
Set the DIP switch (SW1) 2WIRE (Factory setting) 3WIRE
DIP switch
(SW1)
Connector
Connecting cable
(Accessories)
Wired remote
controller cables
WARNING
When using solid core cables, do not use the attached ring terminal. If you use the solid
core cables with the ring terminal, the ring terminal's pressure bonding may malfunction
and cause the cables to abnormally heat up.
B. For strand wiring
(1) Use ring terminals with insulating sleeves as shown in the fi gure below to connect to
the terminal block.
(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the
cables do not come loose.
(3) Use the specifi ed cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(4) Use an appropriate screwdriver to tighten the terminal screws.
Do not use a screwdriver that is too small, otherwise, the screw heads may be dam-
aged and prevent the screws from being properly tightened.
(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
(6) See the table for the terminal screw tightening torques.
(7) Please do not fi x 2 power supply cables with 1 screw.
Strip 3/8 in
(10 mm)
Ring terminal
Sleeve
Screw with
special washer
Screw with
special washer
Ring terminal
Terminal block
Ring terminal
Cable
Cable
WARNING
Use ring terminals and tighten the terminal screws to the specifi ed torques, otherwise,
abnormal overheating may be produced and possibly cause heavy damage inside the
unit.
Terminal number Tightening torque
M4 screw (Power supply/Change: L1, L2 (N), GND) 11 to 16 Ibf·in (1.2 to 1.8 N·m)
6.3.2. Transmission cable
1-3/16 in (30 mm)
1-3/8 in (35 mm)
Shielded cable
(no fi lm)
• When the 2 cables are attached.
GOOD PROHIBITED
Different diameter Connect to 1 side
WARNING
Tighten the terminal screws to the specifi ed torques, otherwise, abnormal overheating
may be produced and possibly cause heavy damage inside the unit.
Terminal number Tightening torque
M3 screw (Transmission/X1, X2) 4.4 to 5.3 Ibf·in (0.5 to 0.6 N·m)
CAUTION
To peel the fi lm from the lead cable, use a dedicated tool that will not damage the
conductor cable.
When installing a screw on the terminal block, do not cut the cable by overtightening
the screw. On the other hand, an undertightened screw can cause faulty contact, which
will lead to a communication failure.
Remove it with the following sequence in case of the state with the grille.
En-9
6.5. Optional parts wiring
6.5.1 Connector and DIP switch position
Output terminal (CNB01)
SW4
SW3
SW2
SW1
DIP switch
(SET 2)
Apply voltage terminal
Dry contact
terminal
(CNA01)
(CNA04)
(CNA02)
(CNA03)
ON OFF
Controller PCB
Name Application
CNA01
Apply voltage terminal For external input
CNA03
CNA02 Dry contact terminal
CNA04
DIP switch SET 2 (SW2) Input signal type switching
CNB01 Output terminal For external output
6.5.2 Connection methods
Wire modification
(1) Remove insulation from wire at-
tached to wire kit connector.
(2) Remove insulation from field
supplied cable. Use crimp type
insulated butt connector to join field
cable and wire kit wire.
(3) Connect the wire with connecting
wire with solder.
IMPORTANT:
Be sure to insulate the connection between the
wires.
Locally purchased
Solder and insulate the connected parts.
Wire kit connector
(optional parts)
Connection terminals and wiring arrangement
In following figure, all the possible connectors are connected for description.
In actual installation, you cannot connect all the connectors at once.
CNA01
CNA04
CNA02
CNA03
CNB01
Controller PCB
Cable tie
(Locally purchased)
Connecting cables
6.6. External input and external output (Optional parts)
6.6.1 External input
• Indoor unit can be Operation/Stop, Emergency stop or Forced stop by using indoor unit
PCB CNA01 or CNA02.
• “Operation/Stop” mode, “Emergency stop” mode or “Forced stop” mode can be selected
with function setting of indoor unit.
• Indoor unit can be Forced thermostat off by using indoor unit PCB CNA03 or CNA04.
• A twisted pair cable (22 AWG) should be used. Maximum length of cable is 492 ft (150
m).
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• The wire connection should be separate from the power cable line.
6.4. Wiring
Connect the end of the connection cable fully into the terminal block.
Screw
Conduit holder
Lock nutConduit connector
Wired remote controller
cable and optional parts
cables (if necessary)
Transmission cables
(The grommet edging is not used.)
Wired remote controller
cable connection terminal
Wired remote
controller cable
L1, L2(N):
Power supply
cable
Power supply
earth (ground)
cable
X1, X2:
Transmission
cable
Cable tie (Accessories)
Earth (ground)
terminal for wired
remote controller
(if necessary)
• Fix the conduit with the supporters as shown below.
Conduit (Power supply cable)
Indoor unit
Supporter
30 in
(756 mm)
or less
54 in
(1,361 mm)
or less
54 in
(1,361 mm)
or less
54 in
(1,361 mm)
or less
En-10
Input select
Use either one of these types of terminal according to the application. (Both types of
terminals cannot be used simultaneously.)
● Apply voltage terminal ([CNA01], [CNA03])
When a power supply must be provided at the input device you want to connect, use the
Apply voltage terminal ([CNA01], [CNA03]).
*a
*b
*1
CNA01
CNA03
*a
*a
Input
device 1
Input
device 2
Input
device 3
Load
resistance
Load
resistance
Load
resistance
DC power supply
12 to 24V
Connected unit
P.C.B
*1:
Make the power supply DC 12 to 24 V. Select a power supply capacity with an ample
surplus for the connected load.
Do not impress a voltage exceeding 24 V across pins 1-2, and 1-3.
*a: The allowable current is DC 5 mA to 10 mA. (Recommended: DC 5 mA)
Provide a load resistance such that the current becomes DC 10 mA or less.
Select very low current use contacts (usable at DC 12 V, DC 1 mA or less).
*b: The polarity is [+] for pin 1 and [-] for pin 2 and 3. Connect correctly.
When connected to Apply voltage terminals of multiple indoor units with a connected unit,
be sure to make a branch outside the indoor unit using a pull box, etc. as shown on below
example.
CNA01
CNA01
CNA01
DC power supply
12 to 24V
Connected unit
Load
resistance
P.C.B
P.C.B
P.C.B
Input
device 1
Input
device 2
Indoor unit
Indoor unit
Indoor unit
Load
resistance
● Dry contact terminal ([CNA02], [CNA04])
When a power supply is unnecessary at the input device you want to connect, use the Dry
contact terminal ([CNA02], [CNA04]).
CNA02
*c
*c
*c
*d
CNA04
P.C.B
GND
Ch 1
Ch 3
Ch 2
Connected unit
*c: Select very low current use contacts (usable at DC 12 V, DC 1 mA or less).
*d: The wiring is different from Apply voltage terminals. Be sufficiently careful when wiring.
When connected to Dry contact terminals of multiple indoor units with a connected unit,
insulate each indoor unit with relay, etc. as shown on below example.
K1
CNA02
CNA02
CNA02
K2
K3
K4
K5
K6
Power supply for relay
Indoor unit
Indoor unit
Indoor unit
Input device 2
Input device 1
K1 - K6: Relay
(Device for DC Current)
P.C.B
P.C.B
P.C.B
NOTE :
When connected to multiple indoor units directly, it will cause breakdown.
Operation behavior
● Input signal type
The input signal type can be selected.
It is switched by DIP switch on the indoor unit PCB.
Pulse
Edge
The width of pulse must be
longer than 200 msec.
DIP switch [SET2 SW2] Input signal type
OFF (Factory setting) Edge
ON Pulse
● When function setting is “Operation/Stop” mode.
[In the case of “Edge” input]
Connector Input signal Command
Ch1 of CNA01 or CNA02
OFF → ON Operation
ON → OFF Stop
[In the case of “Pulse” input]
Connector Input signal Command
CNA01 or CNA02
Ch1
OFF → ON
Operation
Ch2
OFF → ON
Stop
* The last command has priority.
* The indoor units within the same remote controller group operates in the same mode.
● When function setting is “Emergency stop” mode.
[In the case of “Edge” input]
Connector Input signal Command
Ch1 of CNA01 or CNA02
OFF → ON Emergency stop
ON → OFF Normal
[In the case of “Pulse” input]
Connector Input signal Command
CNA01 or CNA02
Ch1 OFF → ON Emergency stop
Ch2 OFF → ON Normal
* All indoor units of same refrigerant system stops when Emergency stop operates.
En-11
● When function setting is “Forced stop” mode.
[In the case of “Edge” input]
Connector Input signal Command
Ch1 of CNA01 or CNA02 OFF → ON Forced stop
ON → OFF Normal
[In the case of “Pulse” input]
Connector Input signal Command
CNA01 or CNA02
Ch1 OFF → ON Forced stop
Ch2 OFF → ON Normal
* When the forced stop is triggered, indoor unit stops and Operation/Stop operation by a
remote controller is restricted.
* When forced stop function is used with forming a remote controller group, connect the
same equipment to each indoor unit within the group.
• Selection method of functions
“Operation/Stop” mode or “Emergency stop” mode, “Forced stop” mode can be selected
with function setting of indoor unit.
● Forced thermostat off function
[“Edge” input only]
Connector Input signal Command
Ch3 of CNA03 or CNA04
OFF → ON Thermostat off
ON → OFF Normal
(2) External output
• A twisted pair cable (22AWG) should be used. Maximum length of cable is 82 ft (25 m).
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• Output voltage: Hi DC12V±2V, Lo 0V.
• Permissible current: 50mA
Output select
● When indicator etc. are connected directly
Indicator 1
Indicator 2
Indicator 3
Indicator 4
connected unit
P.C.B
CNB
01
● When connecting with unit equipped with a power supply
CNB
01
P.C.B
Connected
device 1
Connected
device 2
Connected
device 3
Connected
device 4
connected unit Relay (Locally purchased)
Operation behavior
* If function setting "60" is set to "00"
Connector Output voltage Status
CNB01
External output 1
Pins 1-2
0V Stop
DC 12 V Operation
External output 2
Pins 1-3
0V Normal
DC 12 V Error
External output 3
Pins 1-4
0V Indoor unit fan stop
DC 12 V Indoor unit fan operation
External output 4
Pins 1-5
0V External heater OFF
DC 12 V External heater ON
● Indoor unit fan setting for external heater
Fan setting when turning ON output to the connected external heater can be set by
changing Dip switch on PC board.
Dip switch
[SET2 SW3]
Fan setting when
ON is output to the
external heater
Explanation
OFF
(Factory setting)
OFF
For the fan setting details, see the
Design & Technical Manual.
ON ON
7. FIELD SETTING
There are 3 methods for address setting by FIELD SETTING as follows.
Please set by either of the methods.
Each setting method is described in below (1) to (3).
(1)
IU AD, REF AD SW settings:
This section (7.1. Setting the address)
(2) Remote controller settings: Refer to the wired or wireless remote controller manual
for detailed setting information. (Set IU AD, REF AD
SW to 0)
(3) Automatic address settings: Refer to the outdoor unit manual for detailed setting
information. (Set IU AD, REF AD SW to 0)
7.1. Setting the address
Manual address setting method
• The indoor unit address and the refrigerant circuit address can also be set up through
the wireless remote controller
CAUTION
Be sure to turn OFF the power before performing the fi eld setting.
• Please set it according to the following procedures when setting manually.
[Front panel remove and installation]
Intake grill remove.
(1) Open the intake grille.
(2) Pull down the knob.
(3) Lift the intake grille upward and until the beating at the top of the intake grille is
removed.
Mounting
shaft
Front panel
Bearing
Intake
grille
Knob
Intake
grille
Front panel removal.
(1) Remove intake grille (Refer to the item of intake grille removal.)
(2) Remove 6 screws.
(3) Push the [▲] part on the lower part of the body upwards with your thumb of both
hands to detach the 2 hooks, and then pull the front panel forward to remove it.
Front panel
Screws (6 position)
[▲] mark
Push
Push
Wall hook
bracket
(4) The front panel is pulled to the front, raising the upper surface, and a front panel is
removed.
Front panel
Piping work can be made easier by laying out, shaping, and temporarily fastening the
connection pipe and connection cable beforehand.
En-12
• Open the control box cover.
• Open the switch cover.
Open
Switch cover
Rotary switch
Example: “0”
Rotary switch Ex-
ample: “0”
CAUTION
Use an insulated screwdriver to set the dip switches.
Be careful not to make mistakes for switch settings.
(1) Indoor unit address
Rotary switch (IU AD × 1)....Factory setting “0”
Rotary switch (IU AD × 10)....Factory setting “0”
When connecting multiple indoor units to 1 refrigerant system, set the address at IU
AD SW as shown in the Table A
(2) Refrigerant circuit address
Rotary switch (REF AD × 1)....Factory setting “0”
Rotary switch (REF AD × 10)....Factory setting “0”
In the case of multiple refrigerant systems, set REF AD SW as shown in the Table A
for each refrigerant system.
Set to the same refrigerant circuit address as the outdoor unit.
Setting Setting range Type of switch
Indoor unit ad-
dress
0 to 63
Setting
example
2
IU AD × 10 IU AD × 1
Refrigerant
circuit address
0 to 99
Setting
example
63
REF AD × 10 REF AD × 1
Table A
Address
Rotary Switch Setting
Address
Rotary Switch Setting
Refrigerant
circuit
REF AD SW Indoor unit IU AD SW
×
10
×
1
×
10
×
1
000000
101101
202202
303303
404404
505505
606606
707707
808808
909909
10 1 0 10 1 0
11 1 1 11 1 1
12 1 2 12 1 2
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
99 9 9 63 6 3
Do no
t set the indoor unit address (IU AD SW) at 64 to 99. It may result in failure
.
(3) Remote controller address
i) 3-wire type
Rotary switch (RC AD SW)....Factory setting “0”
When connecting multiple indoor units to 1 standard wired remote controller, set the
address at RC AD SW in sequence from 0.
Setting Setting range Type of switch
Remote controller ad-
dress
0 to 15
Setting
example
0
RC AD
Example
If 4 indoor units are connected.
Remote
controller
Indoor unit
Indoor unit
Indoor unitIndoor unit
RC AD SW
0
RC AD SW
1
RC AD SW
2
RC AD SW
3
RC AD SW 0 1 2 3 4 5 6 7
Address 0 1 2 3 4 5 6 7
RC AD SW 8 9 A B C D E F
Address 8 9 10 11 12 13 14 15
ii) 2-wire type
Rotary switch (RC AD SW)...Factory setting “0”
Since the remote controller address settings are automatically confi gured, you do not
need to confi gure them.
If confi guring manually, it is necessary to confi gure both the indoor unit and the
remote controller. For details, please refer to the remote controller manual.
7.2. Custom code setting
Selecting the custom code prevents the indoor unit mix-up. (Fig. B)
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Fig. B
Code change
Indoor unit
Remote
controller
Confusion
A B C D
A B C D
• Custom code setting for indoor unit
Set the DIP switch SET 3 SW1, 2, referring to the Table B.
DIP switch “SET3”
SW
1
SW
2
SW
3
SW
4
ON
OFF
Table B
Custom code
A (Factory setting) B C D
DIP switch SET 3
SW1
OFF ON OFF ON
DIP switch SET 3
SW2
OFF OFF ON ON
En-13
7.3. Function setting
WARNING
Please make this setting after completing all construction works.
• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
• Refer to “7.1. Setting the address” for indoor unit address and refrigerant circuit address
settings.
• Turn the power of the indoor unit ON before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air tight
test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Function
number
Setting number Default Details
Filter indica-
tor interval
11
00 Standard
Adjust the filter cleaning interval
notification. If the notification
is too early, change to setting
01. If the notification is too late,
change to setting 02.
01 Longer
02 Shorter
Filter indica-
tor action
13
00 Enable
Enable or disable the filter indi-
cator. Setting 02 is for use with
a central remote controller.
01 Disable
02
Display only
on central
remote
controller
Horizontal
swing
airflow direc-
tion
24
00 Standard
Adjust the horizontal swing
airflow direction.
(For horizontal swing equipped
models)
01 Left half
02 Right half
Cool air
temperature
trigger
30
00 Standard
Adjust the cool air trigger tem-
perature. To lower the trigger
temperature, use setting 01. To
raise the trigger temperature,
use setting 02.
01 Adjust (1)
02 Adjust (2)
Heat air
temperature
trigger
31
00 Standard
Adjust the heat air trigger
temperature. To lower the trig-
ger temperature by 6 degrees
C, use setting 01. To lower
the trigger temperature by 4
degrees C, use setting 02. To
raise the trigger temperature,
use setting 03.
01 Adjust (1)
02 Adjust (2)
03 Adjust (3)
Auto restart 40
00 Enable Enable or disable automatic
system restart after a power
outage.
* Auto restart is an emergency
function such as for power
failure etc.
Do not start and stop the
indoor unit by this function in
normal operation.
Be sure to operate by the con-
trol unit, converter or external
input device.
01 Disable
Cool Air
Prevention
43
00 Super low
Restrain the cold airflow with
making the airflow lower when
starting heating operation. To
correspond to the ventilation,
set to 01.
01
Follow the
setting on
the remote
controller
External
control
46
00 Start/Stop
Allow an external controller to
start or stop the system, or to
perform an emergency stop.
* If an emergency stop is
performed from an external
controller, all refrigerant sys-
tems will be disabled.
* If forced stop is set, indoor
unit stops by the input to
the external input terminals,
and Start/Stop by a remote
controller is restricted.
01
Emergency
stop
02 Forced Stop
Error report
target
47
00 All
Change the target for reporting
errors. Errors can either be re-
ported in all locations, or only on
the central remote controller.
01
Display only
on central
remote
controller
Fan set-
ting when
cooling
thermostat
OFF
49
00
Follow the
setting on
the remote
controller
When set to 01, the fan stops
when the thermostat is OFF in
cooling operation. Connection
of the wired remote controller
(2-wire type or 3-wire type)
and switching its thermistor are
necessary.
01 Stop
Switching
functions
for external
inputs and
external
outputs
terminals
60
00 Mode 0
• Set this function when con-
necting the VRF system to a
ventilator, economizer, humidi-
fier, or other external device.
• The connection terminal
functions can be changed
depending on the type of ex-
ternal device. For details of the
connection terminal functions,
see the Design & Technical
Manual.
01 Mode 1
02 Mode 2
03 Mode 3
04 Mode 4
05 Mode 5
06 Mode 6
07 Mode 7
08 Mode 8
Control
switching
of external
heaters
61
00
Auxiliary
heater con-
trol 1
Sets the control method for the
external heater being used. For
details of the control method,
see the Design & Technical
Manual.
01
Auxiliary
heater con-
trol 2
02
Heat pump
prohibition
control
03
Heater selec-
tion control
using outdoor
tempera-
ture 1
04
Heater selec-
tion control
using outdoor
tempera-
ture 2
Operating
temperature
switching
of external
heaters
62
00 Setting 0
• Sets the temperature condi-
tions when the external heater
is ON.
• For the temperature condi-
tions, see "Temperature condi-
tions when the external heater
is ON". For a more detailed
explanation, see the Design &
Technical Manual.
01 Setting 1
02 Setting 2
03 Setting 3
04 Setting 4
05 Setting 5
(Forbidden) 70 00
Temperature conditions when the external heater is ON
Temperature (t) when the external heater is ON= Room temperature - set temperature
Set value of function: 61
00 01 02 03 04
Set value of func-
tion: 62
00 t < -5.4°F (-3°C) t ≤ -0.9°F (-0.5°C)
01 t < -3.6°F (-2°C) t ≤ -1.8°F (-1°C)
02 t < -3.6°F (-2°C) t ≤ -3.6°F (-2°C)
03 t < -5.4°F (-3°C) t ≤ -5.4°F (-3°C)
04 t < -7.2°F (-4°C) t ≤ -7.2°F (-4°C)
05 t < -9.0°F (-5°C) t ≤ -9.0°F (-5°C)
7.3.1. Button name and function
OPERATION indicator lamp (Green)
FILTER indicator lamp (Red)
TIMER indicator lamp (Orange)
En-14
(
1
Rear,
2
Right and
3
Bottom piping)
Indoor unit pipe
(heat insulation)
Overlap the insulation.
Connection pipe
(heat insulation)
Bind the pipes together so
that there is no gap.
Vinyl tape
(For
4
Left bottom piping,
5
Left piping,
6
Center piping and
7
Left rear piping)
• Wrap the area which accommodates the rear piping housing section with cloth tape.
• Bind the connection cable with vinyl tape.
• Bundle the piping and drain hose together by wrapping them with cloth tape over the
range within which they fi t into the rear piping housing section.
Connection pipe
Indoor unit pipe
Cloth tape
(Accessories)
Wrap with cloth tape.
Connection cable (Transmission and Remote controller cable)
Connection cable (Power supply cable)
Vinyl tape
Pipe
Pipe
Cloth tape
Drain hose
Wrap with cloth tape
(2) Temporarily fasten the connection cable along the connection pipe with vinyl tape.
(3)
Fasten the connection pipe to the outside wall with a saddle, etc.
(4)
Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain
water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
Saddle*
Pipe
Outside wall cap*
*Locally purchased
Wall
(Outdoors)
Sealer putty*
GOOD
Drain hose
Saddle
Lifted up Wave End in water
PROHIBITED
7.3.2. Checking the function settings
Press and hold the “MANUAL AUTO” button on the indoor unit for 3 seconds to check
the function settings. It is necessary to disconnect the power in order to return to normal
operation mode.
(1) Indoor unit and refrigerant address indication
Indication pattern
Indicator name
Indication pattern
Indoor unit address Refrigerant address
OPERATION indicator lamp (Green)
ON Flash (1.0s ON/1.0s OFF)
TIMER indicator lamp (Orange) Address: tens place (0.5s ON/0.5s OFF)
FILTER indicator lamp (Red) Address: ones place (0.5s ON/0.5s OFF)
• Indoor unit address example
(Example) ADDRESS : 24
OPERATION indicator
lamp (Green)
TIMER indicator lamp
(Orange)
FILTER indicator lamp
(Red)
10 sec
1 cycle 12 sec
8 sec
ON
OFF
0.5s
0.5s 0.5s 0.5s
0.5s
0.5s
0.5s 0.5s
0.5s
0.5s
0.5s 0.5s
ON
OFF
ON
OFF
ON
• Refrigerant address example
(Example) ADDRESS : 30
OPERATION indicator
lamp (Green)
TIMER indicator lamp
(Orange)
FILTER indicator lamp
(Red)
9 sec
1 cycle 12 sec
ON
OFF
1.0s 1.0s 1.0s
1.0s 1.0s 1.0s 1.0s
0.5s
0.5s
0.5s 0.5s 0.5s 0.5s
ON
OFF
ON
OFF
OFF
• Setting details
Function number Item Setting number
01 Indoor unit address 00 to 63
02 Refrigeration address 00 to 99
For use with a remote controller, set all rotary switches to 0, and refer to “7.1. Setting the
address” for details.
All switches are set to 0 at the factory.
(2) Others
Indication pattern
Indicator Name Indication pattern
OPERATION indicator lamp (Green)
Function number; tens place (0.5s ON/0.5s OFF)
TIMER indicator lamp (Orange) Function number; ones place (0.5s ON/0.5s OFF)
FILTER indicator lamp (Red) Setting number: (0 to 9) (0.5s ON/0.5s OFF)
(Example) Function : 31, Setting number : 2
OPERATION indicator
lamp (Green)
TIMER indicator lamp
(Orange)
FILTER indicator lamp
(Red)
11 sec
10 sec
9 sec
1 cycle 12 sec
ON
OFF
0.5s
0.5s
0.5s
0.5s
0.5s
0.5s
0.5s
0.5s
0.5s
0.5s 0.5s 0.5s
ON
OFF
ON
OFF
8. FINISHING
CAUTION
After checking for gas leaks (refer to the Installation Manual of the outdoor unit),
perform this section.
Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do
so may cause water leaks.
8.1. Connection pipe, cable and drain hose
Insulate the drain hose, if necessary, to prevent it from freezing.
(1) Insulate between pipes.
• For
1
Rear,
2
Right and
3
Bottom piping, overlap the connection pipe heat insulation
and indoor unit pipe heat insulation and bind them with vinyl tape so that there is no
gap.
• For
4
Left bottom piping,
5
Left piping,
6
Center piping and
7
Left rear piping, butt
the connection pipe heat insulation and indoor unit pipe heat insulation together and
bind them with vinyl tape so that there is no gap.
En-15
8.2. Installing front cover
Fix the indoor unit
(1) Please remove the spacer.
Indoor Unit
Remove
Spacer
(2) Hook the fi ttings of the indoor unit to the 2 bottom hooks while lowering the unit and
pushing it against the wall.
Bottom hook
Indoor unit
Top hooks
Front panel installation.
(1) First, fi t the lower part of the front panel, and insert top and bottom hooks. (Top center
and both sides)
(2) Attach the 6 screws.
(3) Attach the intake grille.
Intake grill installation.
(1) The fi xing axle of the intake grille is installed on the front panel.
(2) Lay down the intake grille.
Top holes (2 sides)
Top hooks (2 sides)
Top hole (center)
Top hooks (2 sides)
Indoor unit
Top hook (center)
(3) Close the intake grille.
Intake grille
Panel
Check that:
• The top and bottom hooks are hooked fi rmly and the indoor unit does not move to
the front and rear or left and right.
• The indoor unit is accurately positioned horizontally and vertically.
• When connected from the left rear, the drain hose is at the bottom left of the wall
pipe.
(View from indoor)
Connection cable
(Power supply cable)
Wall pipe
Connection pipe
Connection cable (Transmission
and Remote controller cable)
Drain hose
9. TEST RUN
9.1. Test run using Outdoor unit (PCB)
Refer to the Installation Manual for the outdoor unit if the PCB for the outdoor unit is to be
used for the test run.
9.2. Test run using remote controller
• Refer to the Installation Manual for the remote controller to perform the test run using the
remote controller.
• When the air conditioner is being test run, the OPERATION and TIMER indicator lamp
flash slowly at the same time.
10. CHECK LIST
Pay special attention to the check items below when installing the indoor unit(s). After
installation is complete, be sure to check the following check items again.
Check items If not performed correctly
Check
box
Has the indoor unit been installed
correctly?
Vibration, noise, indoor unit may
drop
Has there been a check for gas leaks
(refrigerant pipes)?
No cooling, No heating
Has heat insulation work been com-
pleted?
Water leakage
Does water drain easily from the indoor
units?
Water leakage
Is the voltage of the power source the
same as that indicated on the label on
the indoor unit?
No operation, heat or burn damage
Are the wires and pipes all connected
completely?
No operation, heat or burn damage
Is the indoor unit earthed (grounded)? Short circuit
Is the connection cable the specified
thickness?
No operation, heat or burn damage
Are the inlets and outlets free of any
obstacles?
No cooling, No heating
Does start and stop air conditioner
operation by remote control unit or
external device?
No operation
After installation is completed, has the
proper operation and handling been
explained to the user?
En-16
11. ERROR CODES
If you use a wired type remote controller, error codes will appear on the remote controller
display. If you use a wireless remote controller, the lamp on the photodetector unit will
output error codes by way of blinking patterns. See the lamp blinking patterns and error
codes in the table below.
Error indications
Wired Remote
Controller Error
code
Error contents
OPERATION
lamp (green)
TIMER lamp
(orange)
FILTER lamp
(red)
(1) (2)
Remote controller
communication error
(1) (4)
Network communication
error
(1) (6)
Peripheral unit
communication error
(2) (6)
Indoor unit address
setting error
(2) (9)
Connection unit number
error in wired remote
controller system
(3) (1)
Indoor unit power supply
abnormal
(5) (1)
Indoor unit main PCB
error
(3) (10)
Indoor unit
communication circuit
(wired remote controller)
error
(4) (1)
Indoor unit room temp.
thermistor error
(4) (2)
Indoor unit heat ex.
temp. thermistor error
(5) (1)
Indoor unit fan motor 1
error
(5) (2)
Indoor unit coil
(expansion valve) error
(5) (3)
Indoor unit water drain
abnormal
(9) (15)
Outdoor unit
miscellaneous error
(10) (8)
Poor refrigerant circula-
tion
(13) (1) RB unit error
Display mode
: 0.5s ON / 0.5s OFF
: 0.1s ON / 0.1s OFF
( ) : Number of fl ashing
Wired remote controller display
UTY-RNKU (3-wire type)
Error code
UTY-RNRUZ* (2-wire type)
Status
Air Flow Direction
VT
Off
13
Off
HZ
Economy
Individual
Anti Freeze
Page 1/ 4
Monitor
Next
Page
Error
Information
Set Temp.
Mode
MenuStatus
Fan
Fri 10:00AM
Unoccupied
Error icon
Touch the [Status]. Touch the [Error Information].
2-digit numbers are corresponding to
the error code in the preceding table.
Touch the [Next Page] (or [previous page])
to switch to other indoor unit information.
For more information, refer to the installation manual of the remote controller.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Fujitsu ASUB24TLAV1 Installation guide

ASUB24TLAV1
Fujitsu
Brand
Fujitsu
Model
ASUB24TLAV1
Category
Split-system air conditioners
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents