Badger WB20VTB is a cordless line trimmer with a cutting path diameter of 25/30 cm, powered by a 20V battery. It features a protective cover to prevent objects from being thrown, and an adjustable handle for comfortable use. The tilting angle of the trimmer head can be adjusted for edging and mowing. It uses a 1.60mm diameter nylon spool for cutting.
Badger WB20VTB is a cordless line trimmer with a cutting path diameter of 25/30 cm, powered by a 20V battery. It features a protective cover to prevent objects from being thrown, and an adjustable handle for comfortable use. The tilting angle of the trimmer head can be adjusted for edging and mowing. It uses a 1.60mm diameter nylon spool for cutting.
5001154
CORDLESS LINE TRIMMER
USER’S MANUAL
Description of the parts
1 On/off switch
2 Switch-on inhibit
3 Handle
4 Additional handle
5 Handle support bracket
6 Telescopic tube
7 Height adjustment
8 Prote ctive guard angle adjustor
9 Trimmer head
10 Protective cover
11 Edge cutter adjustor
12 Edge cutter head
13 Handle knob
14 Rechargeable battery
15 Charging station
16 Standard battery charger
14
15
1
1
11
14
6
7
8
10
9
13
5
12
3
2
4
16
2
14
15
2
3
4
SAFETY INFORMATION
WARNING
Read and understand all instructions before using this product. Failure to follow all instructions listed
l injury.
BEFORE USING
• Use extra care when cleaning on stairs.
• Do not use on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
•
• Do not use with a damaged plug. If the tool is not working as it should, or if it has been dropped,
damaged, left outdoors, or dropped into water, return it to an authorized service center.
• When using in direct sunshine, keep out of water.
• Don’t expose to rain when operating the machine.
• Store indoors. Do not expose to rain or water. Avoid direct sunshine.
WHEN USING (THIS APPLIANCE)
• Do not operate power tools in an explosive atmosphere,
such as
gases, or dust. Power tools create sparks that may ignite the dust or fumes.
• To reduce the risk of electric shock, the batttery charger has a polarized plug (one blade is wider than
the other) and will require the use of a polarized extension
cord. A polarized extension cord will require
electrician to install the proper wall outlet. Do not change the equipment plug, extension cord
receptacle, or extension cord plug in any way.
• Never allow children to operate the equipment. Never allow adults to operate the equipment without
proper instruction.
• Wear eye protection that is marked to comply with ANSI Z87.1 when operating this product.
• Do not handle charger, including charger plug, and charger terminals with wet hands.
• Do not charge the unit out
doors.
• Wear heavy long pants, boots, and gloves. Avoid loose garments or jewelry that could get caught in
moving parts of the machine or its motor.
• Do not force the tool. Use the correct tool for your application. The correct tool will work more
designed to work at.
• Do not operate the equipment while barefoot or when wearing sandals or similar lightweight footwear.
• Wear protective footwear that will protect your feet and improve your footing on slippery surfaces.
• Secure long hair so it is above shoulder level to prevent entanglement in any moving parts.
•
n result in loss of balance.
• Do not allow children or untrained individuals to use this unit.
• Do not use the tool if the switch does not turn it on or off. Any tool that cannot be controlled with the
switch is dangerous, and must be repaired.
• Keep all bystanders, children, and pets at least 50 ft. (15 m) away.
5
• For household use only.
• Use only 20 V Badger batteries (LBB202/LBB204).
• Use only Badger charger (Model CGA202US/CGA20US).
• Do not operate this unit when you are tired, ill, or under the
• Do not operate in poor lighting.
• Keep all parts of your body away from any moving parts and all hot surfaces of the unit.
• Do not put any object into openings. Do not use with any opening blocked. Keep openings free of dust,
• Check the work area before each use. Remove all objects that can be thrown or become entangled in
the machine, such as rocks, broken glass, nails, wire, or string.
• Use only identical manufacturer’s replacement parts and accessories. Use of any other parts may
create a hazard or cause product damage.
FOR BATTERY-OPERATED APPLIANCE:
• Prevent unintentional starting, ensure the switch is in the off-
position before connecting to battery
pack, picking up or carrying the appliance. Carrying the appl
energizing appliance that have the switch on invites accidents.
•
•
•
•
•
e.
•
•
•
•
CHILD SAFETY
•
•
•
•
SAFETY INFORMATION
6
WARNING (PROPOSITION 65)
•
•
•
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
SAFETY INFORMATION
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their mean-
ing. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOLS DESIGNATION EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watts Power
min Minutes Time
Alternating Current Type of current
Direct Current Type or a characteristic of current
n
o
No Load Speed Rational speed, at no load
/min Per Minute
Revolutions, strokes, surface speed,
orbits, etc., per minute.
Wet Conditions Alert
Do not expose to rain or use in damp
locations.
Read the Operator’s Manual
To reduce the risk of injury, user must
read and understand operator’s manual
before using this product.
Eye Protection
Wear eye protection with side shields
that are marked to comply with ANSI
Z87.1 when operating this equipment.
Safety Alert Precautions that involve your safety.
No Blade
Do not install or use any type of blade
on a product displaying this symbol.
Ricochet
Thrown objects can ricochet and result
in personal injury or property damage.
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
7
8
The following signal words and meanings are intended to explain the levels of risk associated
with this product.
WARNING
• To avoid serious personal injury, do not attempt to use this product until you have read this Owner's
Manual thoroughly and understand it completely. If you do not understand the warnings and
instructions in this Owner's Manual, do not use this product.
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before operating a power tool, always
wear safety goggles,
safety glasses with side shields, or a full face shield when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always
use eye protection that is marked to comply with ANSI Z87.1.
•
SYMBOL SIGNAL MEANING
DANGER
Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
SYMBOLS
This products can be only fit with cutting attachment of nylon spool with line, it can not fit with metal or blade.
Aligh the fout pins (1,2,3,4)of the protective cover with the holes of 19 the spool base drum A, B, C, D
one-to-one match, use screws (5) to fix them together.
Installing the protective cover (Fig. 3)
Install additional handle (Fig. 4)
Put the D type handle base to the gap of the handle bracket, aligh the hole of the handle (4) and the
bracket (5), use knob (3) and nut (18) to assemble the handle tighten enough.
9
ASSEMBLY INSTRUCTIONS
Attention- risk of injury!
Always remove the rechargeable battery from the device before all work.
Attention
The rubber side of the handle is in the side of the spool, while the groove side of the handle face to
operator.
SPECIFICATIONS
Voltage 20 Volts
No Load Speed 7,000 rpm
Cutting head Automatic feed
Cutting Line Diameter 1.60 mm
Cutting Path Diameter 25/30 cm
CGA20US
Battery Pack
Charger
LBB202
Putting the machine in operation (Fig. 5 and 6)
■ Insert the charged battery in the strimmer until the interlock (15) latches. The rechargeable battery
can only be inserted in the strimmer in one position (Fig.5).
Directions for set lenght adjustment and the use of the set as edge cutter (Fig. 7, 8, 9, 10)
The tube length may be adjusted to suit your height (Fig. 7):
■ To do so, turn the ribbed plastic sleeve clockwise to loosen the connection. Adjust the tube to the suitable
length and fasten the connection by turning the tapped sleeve anti-clockwise.
Adjusting the tilting angle (Fig. 8):
■ Press the button (8) - the strimmer head is disengaged and can be pivoted in 72° relative to the shaft.
Adjusting for edge trimming (Fig. 7, 8 , 9, 10):
■ Set the tilting angle as previously described.
■ Press the edge cutter adjustor (11) and rotory the handle with clockwise with 180°, then the edge
cutter spool would directs to ground. It’s for edge trimming.
Instructions for operating the mowing machine (Fig.11)
Move the mowing machine evenly from oneside to another.
■ If possible, mow by using the left half of the mowing machine.
The mowed parts of plants and / or stones will thus be hurled forward away from the operating person.
■ The best possible cutting result are achieved when you hold the trimmer with an angle of 20°- 30° to the
left side.
■ Avoid contact between the mowing string and obstacles such as fences, walls, stones, etc. This leads to
excessive wear and tear.
Changing the spool (Fig. 12)
10
OPERATION INSTRUCTIONS
Attention- risk of injury!
Always remove the rechargeable battery from the device before all work.
Press the nylon spool head cap claw (2) and pick out the worn spool (3), replace a new spool to the spool
frame (4)with the line out of the hole of the spool frame, and replace the cap (1) to the nylon head.
Attention: The nylon head is with single line, not double.
Attention
When inserting the battery do not actuate the switch-on inhibit (2) and the on/off switch (1).
Attention
On/off switch can only be activated after the switch-on inhibit (2) is pressed.
■ Adopt a safe stance. Hold the strimmer in both hands.Do not set the cutting device down on the
ground. Press the switch-on inhibit (2) to right and actuate the switch (1) (Fig. 6). After switching
on, the switch-on inhibit (2)must no longer be held.
■ In order to switch off, release the switch (1) (Fig. 6).
Repair service
Repairs to electric power tools should only be carried out by a specialised electrician.
11
CARE AND MAINTENANCE
Attention- risk of injury!
Attention - risk of injury! Always remove the rechargeable battery from the device before all work.
Clean your battery-operated mowing machine thoroughly each time after you use it. Remove the grass and
dirt.
Clean the ventilation openings. It is best to clean the plastic parts with a wet cloth and a soft detergent.
Never use aggressive detergents or solvents. Do not pour water into the machine and do not sprinkle it with
water. Store the mowing machine in a dry place, never expose it to frost and keep it out of children‘s reach.
For more extensive maintenance or repairs, give the mowing machine to the service center.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Badger WB20VTB is a cordless line trimmer with a cutting path diameter of 25/30 cm, powered by a 20V battery. It features a protective cover to prevent objects from being thrown, and an adjustable handle for comfortable use. The tilting angle of the trimmer head can be adjusted for edging and mowing. It uses a 1.60mm diameter nylon spool for cutting.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Powerbase GY2247 Owner's manual
-
Trueshopping ST-BC415B User manual
-
Black & Decker GLC1823L20 User manual
-
-
Black & Decker HX210-QS User manual
-
-
Black & Decker GLC1823L20 User manual
-
Parkside PBK 4 A1 Translation Of The Original Instructions
-
-
FLORABEST 273489 Operating instructions
