PAC BKNDK726
The PAC BKNDK726 is a car radio installation kit for Nissan Altima 2005-06 vehicles. The kit's versatile design allows for single DIN, double DIN, and double ISO mount applications, providing flexibility in installing aftermarket radios.
Key Features:
- Vehicle Compatibility: Nissan Altima 2005-06
- Mount Types: Single DIN, Double DIN, Double ISO mount
- ISO Spacers: Included for ISO mount applications
- Rear Support Bracket: Optional for added stability
- Easy Installation: Step-by-step instructions and included hardware simplify the installation process
PAC BKNDK726
The PAC BKNDK726 is a car radio installation kit for Nissan Altima 2005-06 vehicles. The kit's versatile design allows for single DIN, double DIN, and double ISO mount applications, providing flexibility in installing aftermarket radios.
Key Features:
- Vehicle Compatibility: Nissan Altima 2005-06
- Mount Types: Single DIN, Double DIN, Double ISO mount
- ISO Spacers: Included for ISO mount applications
- Rear Support Bracket: Optional for added stability
- Easy Installation: Step-by-step instructions and included hardware simplify the installation process
CUSTOMER HELP LINE
USA 800-336-6500 • Canada 800-245-8777
NOTE: 1) ISO trim ring (DITR726) must be used in place of after-market radio’s trim rings. For ISO mount
applications, mount after-market radio components to side brackets using screws provided with
radio when possible or hardware included with kit.
2) Spacers must read upright (This side up for DBL ISO install).
Attach (1) ISO Spacer to the inside of upper sections
on both Left & Right mounting brackets as shown in
Fig. A.
Cut
Cut
Left
Right
Fig. A
DITR72
6
NOTE: Remove pocket support tabs from both right and lift brackets(shaded) see figure C.
Double DIN & Double ISO Mount Applications
1. Cut and remove center rib from main frame and file edges smooth.
2. Attach the left and right side brackets to the main frame. See figure C below.
3. Attach (1) ISO Spacer to the inside of upper section on both Left & Right mounting brackets
as shown in Fig. A. (See note #2 below)
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides of radio using screws
provided with radio when possible or hardware included with kit.
5. Slide radio component forward or backward for desired look and tighten screws.
6. Attach a rear support bracket to the rear of the radio components and adjust as needed to allow rear support
bracket to rest in the sub-dash (Optional).
Nissan
2005-06 ALTIMA
VEHICLE APPLICATIONS
KIT ASSEMBLY INSTRUCTIONS
IMB726L
IMB726R
Fig. C
Mai
n Frame
NDK726 Mounting Kit
iNDK726
©2015 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 1/13 PRINT Ver. 4/15
Remove all shaded tabs shown
on left and right brackets.
(Left side not shown)
1. Disconnect the Negative battery cable.
2. Carefully pry outward and forward the trim from around the Climate controls,
disconnect the connector attached to the rear and remove trim.
3. Remove the (4) Phillips screws securing the Climate controls to the sub-dash, pull
forward, and lower out of the way.
4. Carefully pry the Vent/Radio trim bezel forward and remove.
5. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
6. Carefully pull radio forward, disconnect all harnesses and antenna lead from rear of
radio and remove radio.
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B.
2. Insert pocket (part # POC726) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of upper section on both Left & Right mounting
brackets as shown in Fig. A. (See note #2 below)
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit (Optional).
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B opposite page.
2. Insert pocket (part # POC726) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the upper section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit (Optional).
NOTE:
1) ISO trim ring (ITR726) may be used in place of after-market radio’s removable trim ring.
2) Spacers must read upright (This side up for single ISO install).
NOTE: ISO trim ring (ITR-726) may be used in place of after-market radio’s removable trim ring.
ITR726
(Top)
Attach (1) ISO Spacer to the inside of upper section
on both Left & Right mounting brackets
as shown in Fig. A.
Left
POC726
IMB726L
IMB726R
Right
Fig. A
DASH DISASSEMBLY INSTRUCTIONS
KIT ASSEMBLY INSTRUCTIONS
KIT ASSEMBLY INSTRUCTIONS
2 3
Fig. B
Main Frame
Main Frame
-
1
-
2
PAC BKNDK726
The PAC BKNDK726 is a car radio installation kit for Nissan Altima 2005-06 vehicles. The kit's versatile design allows for single DIN, double DIN, and double ISO mount applications, providing flexibility in installing aftermarket radios.
Key Features:
- Vehicle Compatibility: Nissan Altima 2005-06
- Mount Types: Single DIN, Double DIN, Double ISO mount
- ISO Spacers: Included for ISO mount applications
- Rear Support Bracket: Optional for added stability
- Easy Installation: Step-by-step instructions and included hardware simplify the installation process
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
