Rane 64S User manual

Rane
Brand
Rane
Model
64S
Category
Audio equalizers
Type
User manual
Data Sheet-1
CP 64S
COMMERCIAL PROCESSOR
Features
• Two fully independent gated Mic/Line Paging Inputs
• Three stereo Program Inputs
• Paging Priority Assign
• Page Ducking
• One gated stereo Priority Program Input
• Page / Program / Zone Expansion
• 7-Band graphic EQ for each Zone
• Servo-Locked-Limiter™ for each Zone
• Optional SCP 2S Security Cover for EQ section only
• Optional PR 2 Remote Page Assign Remote
• Optional ZR 1 Remote Zone Level/Program Select Remote
• NEW! Universal Internal Power Supply (100-240 VAC)
General Description
e CP 64S is a versatile commercial preamplifier designed for
use in restaurants, bars, health clubs and offices. e CP 64S is
capable of serving two independent Zones. Two gated Paging
inputs and four Program inputs are provided. Ports are provided
for expansion of Page, Program or Zone signals. Four levels of
priority are supported:
• Priority Page
• Non-Priority Page
• Priority Program
• Non-Priority Program
e versatility of the CP 64S allows a wide variety of system
configurations while providing simple and intuitive controls.
Two gated Paging Inputs capable of receiving mic or line
level input are provided. Each features independent Mic/Line
Pad, Gain Trim, detector reshold, Zone Assign and Zone
Level controls. Internally selectable phantom power is provided
for each input. Each Paging input may be summed Pre- or Post-
Zone Level control to allow setting Paging Level independent of
Zone Level. An internal Paging Priority switch allows a “master”
pager to override non-priority paging in its assigned zones, while
allowing true dual zone independent paging. If no Paging Prior-
ity is selected, the Paging inputs mix together for applications
like karaoke.
Four stereo Program inputs are provided with independent
Input Level controls. Any one of the four Program inputs may
be independently assigned in each Zone. One of the Program
inputs is a gated Priority Program input. When signal is detected
at its input, it overrides any non-priority Program selection in the
assigned Zones. e Priority detector features internal, adjustable
reshold and Release-Time controls.
e CP 64S has two Zone outputs: Zone 1 is stereo: Zone 2
is mono. Each Zone features independent:
• Level
• Program Select
• Ducker On/O
• Ducker Depth
• Servo-Locked-Limiter™
• 7 Band EQ (±12 dB)
Versatile wired remote control interface ports are provided
for Paging assignment, Zone Level and Zone Program source
selection. Paging Zone and Source/Volume remote controls are
available as accessories.
Many options allow the installer to determine exactly which
controls are employee accessible. e SCP 2S is an optional se-
curity cover for the CP 64S’s front panel EQ section. Any or all
other front panel knobs can be removed and replaced with hole
plugs — six are included with the SCP 2S. Front panel Ducker
Depth controls are screw driver adjust. e remote controls allow
blank Decora™ plates to be remote control security covers. e
remote knobs can also be individually replaced with hole plugs.
RMT 1 & 2RMT 1 & 2
12 12
ZONE 1 ZONE 2
PAGING
ZONE ASSIGN LEVEL
L1 P
L2 L3
4k630 1.6k40 100 250 10k
CP 64S
COMMERCIAL
PROCESSOR
ACTIVEACTIVE
PAGE 2PAGE 1 LINE 1 LINE 2 LINE 3 PRIORITY
ONOFF
SIG OL
DUCKER
DEPTH
PROGRAM
SELECT
LEVEL
L1 P
L2 L3
ONOFF
SIG OL
DUCKER
DEPTH
PROGRAM
SELECT
LEVEL
PROGRAM INPUT LEVELS ZONE 1 ZONE 2 ZONE 2
4k630 1.6k40 100 250 10k
ZONE 1
POWER
RMT RMT
12
•
6
•
•
•
6
12
0
+
100
64
28
100
64
28
100
64
28
100
64
28
100
64
28
100
64
28
100
64
28
100
64
28
Optional SCP 2S Equalizer-only Security Cover
DATA SHEET
Data Sheet-2
CP 64S
COMMERCIAL PROCESSOR
Parameter Specication Limit Units Conditions/Comments
MIC/LINE PAGING INPUTS Two mono All controls duplicated for both inputs
..........Input Type Euroblock Balanced; Instrumentation amplier
..........RFI Filter Yes
..........Gain range +30 to +60 2 dB Continuously adjustable
..........Frequency Response 30 Hz to 40 kHz +0/-3 dB Maximum gain
..........Input Referred Noise -125 1 dBu Gain: 60 dB, Rs: 150 Ω, BW: 20 kHz
..........CMR 40 min dB 20 to 20 kHz
..........THD+N .05 .01 % Gain: 30 dB, +4 dBu out, 1 kHz, BW: 80 kHz
..........Phantom Power +15 4% VDC Internal switch
..........Mic Input impedance 500 1% Ω Each leg to ground
..........Line Pad 30 1 dB
..........Line Input impedance 14.5k 1% Ω Each leg to ground. Defeats phantom power
..........Signal Detector Range o to +4 typ dBu Continuously adjustable
..........Signal Detector Attack .5 typ msec Fixed
..........Signal Detector Release 3 typ sec Fixed
..........Overload Indicator +16 1 dBu 4 dB before clipping.
..........Front Panel Zone Assign Remote, Z1, Z2, Both Z1 = Zone 1; Z2 = Zone 2
..........Remote Zone Assign O, Z1, Z2, Both Internal pull-up; Active low;
Switch closure to ground or 5 volt TTL logic.
..........Pre/Post Paging assign Summed with program Pre VCA or Post VCA via Internal switch
..........Page Priority Assign P1 (Page 1)
NO (none)
P2 (Page 2)
1 dBu Priority pager overrides non-priority pager only
in assigned zones; Selecting NONE allows the
two pagers to mix.
..........Paging Zone Level Adjust o to 0 dB Independent for each Zone
..........Page Remote Selector 11 = O
10 = Z1 (Zone 1)
01 = Z2 (Zone 2)
00 = Both
1 dBu Internal pull-up. Active low;
Switch closure to Ground or 5 volt TTL logic.
PROGRAM INPUTS Four stereo All controls duplicated for all four inputs
..........Input Type RCA Unbalanced
..........Input Level adjust o to 0 dB
..........Frequency Response 10 Hz to 50 kHz +0/-3 dB
..........Input impedance 10 k 20% Ω
.....Priority Program Input
...............Input Detector Range o to -35 typ dBu Internal trim, factory set to -50 dBu
...............Release Time Range 5 to 20 typ sec Internal trim, factory set to 12 seconds
...............Attack Time 50 typ msec For a 20 dB step; Fixed.
...............Assign OFF, Z1, Z2 or Both
EXPAND OUTPUTS All controls duplicated for both zones
..........Number of Expand Outputs Two Z1 & Z2, both mono
..........Expand Selector Zone
Program only
Page only
Note: If a Page signal is summed Post-VCA, it
is not present on the Expand Zone output. It is
available for the Expand Page output.
..........Output Type Balanced Cross-coupled; Euroblock connector
..........Gain: Zone 12 1 dB
....................Page/Program 6 1 dB
..........Frequency Response 10 Hz to 50 kHz +0/-3 dB
Features and Specifications
continued...
Data Sheet-3
CP 64S
COMMERCIAL PROCESSOR
Parameter Specication Limit Units Conditions/Comments
..........S/N -84 1 dBr re +4 dBu. BW: 20 Hz-20 kHz
..........THD+N .05 .01 % +4 dBu, 1 kHz, BW: 80 kHz
..........Crosstalk -75 max dB 1 kHz, Rs: 25 Ω, ch/ch
..........Output impedance 100 1% Ω Each leg
..........Maximum Output +24 dBu typ Ri: 2 kΩ
ZONE OUTPUTS
..........Number of outputs Two Zone 1 Stereo, Zone 2 mono
..........Output Type Euroblock Balanced; Cross-coupled
..........Gain: From Program Inputs 12 1 dB
....................From Page Inputs 6 1 dB
..........Frequency Response 10 Hz to 50 kHz +0/-3 dB
..........S/N -84 1 dBr re +4 dBu. BW: 20 Hz-20 kHz
..........THD+N .05 .01 % +4 dBu, 1 kHz, BW: 80 kHz
..........Crosstalk -75 max dB 1 kHz, Rs: 25 Ω, (L/R or ch/ch)
..........Output impedance 100 1% Ω Each leg
..........Maximum Output +20 typ dBu Ri = 600 Ω
..........Signal Present Indicator -20 typ dBu Maximum
..........Overload Indicator +16 typ dBu 4 dB before clipping
..........Ducker: Enable ON/OFF Independently defeatable for each Zone
...............Depth Range -50 to -6 typ dB Continuously adjustable
..........Limiter: reshold Range -20 to +20 typ dB Continuously adjustable
...............Attack Time 20 typ msec For a 10 dB step; Fixed.
...............Release Time 250 typ msec For a 10 dB step; Fixed.
...............Ratio 15:1 typ Soft knee.
PROGRAM SELECTION
..........Local (Front Panel) L1, L2, L3 or P (priority) Independent for each Zone
..........Zone RMT Selector 11 = L1
10 = L2
00 = L3
01 = P
Internal pull-up. Active low.
Switch closure to ground or 5 volt TTL.
Gray Code logic.
..........Zone RMT Volume
(RMT engaged)
Attenuation = 64 mV/dB
Range 0 V to +5 V (0 dB to -78 dB)
Control element: 2 kΩ pot, reverse-log taper;
Or any ground referenced 0-5 VDC control.
..........O Isolation -80 typ dB 1 kHz, Rs: 25 Ω
EQ CIRCUITS
..........Boost/Cut Range +12 to -12 .5 dB
..........ISO Center Frequencies 40, 100, 250, 630, 1.6k,
4k, 10k
3% Hz Zone 1: Stereo 7-band.
Zone 2: Mono 7-band.
..........Filter Bandwidth 2 3% oct
UNIT: Agency Listing UL/cUL/CE
..........Universal Line Voltage 100-240 VAC, 50/60 Hz 12 watts
..........Construction All Steel
..........Size 1.75"H x 19"W x 8.5"D 1U (4.4 cm x 48.3 cm x 21.6 cm)
..........Weight 5 lb (2.3 kg)
Shipping: Size 4.5" x 20.3" x 13.75" (11.5 cm x 52 cm x 35 cm)
..........Weight 9 lb (4.1 kg)
Note: 0 dBu = 0.775 Vrms
Data Sheet-4
CP 64S
COMMERCIAL PROCESSOR
Block Diagram
LEFT
RIGHT
PAGE
7-BAND EQ
ZONE 2
ZONE 2
EXPAND
ZONE 1
EXPAND
+
-
+
DEPTH
THRESHOLD
Z2 LIMIT
Z2 POST PA GE
Z2 VC
Z1 VC
7-BAND EQ
ZONE 1 LEFT
Z1 POST PA GE
+
-
+
Z1 VC
7-BAND EQ
ZONE 1 RIGHT
+
-
THRESHOLD
Z1 LIMIT
+
+
+
-
PROGRAM
ZONE
PAGE
+
Z1 PAGE
+
+
Z1 PRE PA GE
Z2 PAGE
PAGE
ZONE
PROGRAM
-
+
+
Z2 PRE PA GE
DUCKER
MONO
PAGE
DUCKER
DEPTH
PAGE
DUCKER
DEPTH
+
+
INPUT
SELECTOR
ZONE 2
ZONE 1
INPUT
SELECTOR
RIGHT
LEFT
RIGHT
LEFT
RIGHT
LEFT
+
PRGM PRIORITY
THRESHOLD
0 dB
LINE 1
LINE 2
LINE 3
ASSIGN
PRIORITY
OFF
Z1
Z2
BOTH
PAGE 1 DETECT SENS.
LOGIC
ASSIGN
PRIORITY
PAGE 2
PAGE 1
+
-
+
-
PAGER
P1
NONE
P2
REMOTE ZONE ASSIGN
P1
P2
P1
LOCAL ZONE ASSIGN
P2
PAGE
ASSIGN
Z1
RMT
Z2
BOTH
BOTH
OFF
Z2
Z1
MIC/
LINE
MIC/
LINE
PHTM PWR
PHTM PWR
TRIM
TRIM
DET
P1
P2
PAGE 2 DETECT SENS.
DET
+
+
Z1 PAGE LEVEL
Z2 PAGE LEVEL
PRE/POST VCA
Z1 PRE PA GE
Z1 PAGE
Z1 POST PA GE
Z2 POST PA GE
PRE/POST VCA
Z2 PRE PA GE
Z2 PAGE
SELECT
PROGRAM
REMOTE
CH 4
CH 1
CH 3
CH 2
LOCAL
Z2
Z1
Z2
Z1
LOGIC
SELECT
CHANNEL
+
Z1 VC
+
AUTO FADE
Z2 VC
+5
LEVEL
RMT
LOCAL
ZONE 1
ZONE 1
RMT/LOCAL
RMT
LOCAL
+5
ZONE 2
LEVEL
RMT/LOCAL
ZONE 2
RMT SEL
PAGE DUCKER
PRIORITY
PA D
30dB
PA D
30dB
15V
15V
*
*
30 TO 60dB
30 TO 60dB
OR
11
00
01
10
01
00
11
10
(ACTIVE LOW)
PAGE
*
+4dB
-
+4dB
-
PAGE BRIDGE
* INTERNAL CONTROLS
OL
*
*
00
10
01
11
(ACTIVE LOW)
GRAY CODE
RMT
RMT
Z1
Z2
*
TIME
RELEASE
PRIORITY
*
12 24 SEC.
ON/OFF
-50dB
-6dB
ON/OFF
-6dB
-50dB
OL
SIG
OL
SIG
+20dB
-20dB
+20dB
-20dB
*
P1 ACTIVE
P2 ACTIVE
PAGE
PRGM
(FRONT PANEL)
(FRONT PANEL)
(FRONT PANEL)
(FRONT PANEL)
6 dB
0 dB
0 dB
0 dB
6 dB
6 dB
6 dB
6 dB
6 dB
6 dB
6 dB
-60dBu -35dBu
P
R
O
G
R
A
M
I
N
P
U
T
S
P
A
G
E
I
N
P
U
T
S
A
COM
B
B
COM
A
COM
B
A
COM
B
A
COM
B
A
COM
A
B
COM
A
B
COM
A
B
COM
B
A
Data Sheet-5
CP 64S
COMMERCIAL PROCESSOR
Remote Controls
Two optional wired remote control units are available. e PR 2
allows remote control of Page 1 and Page 2 Zone Assign selec-
tion. e ZR 1 allows remote control of Zone Level and Zone
Program selection. One PR 2 and two ZR 1 remotes may be
used with each CP 64S. e PR 2 and ZR 1 may be installed in
standard electrical boxes (minimum depth 2.25"). e remotes
connect to the CP 64S through Euroblock connectors.
e PR 2 is a 5-wire remote with 2 bits to select Page 1 As-
sign, one wire for shield/gnd and 2 bits for Page 2 Assign. Selec-
tor logic is active low BCD with pull-up provided in the CP 64S.
Control may be a simple switch closure to ground or 5 volt TTL.
Page 1 and Page 2 bits may be paralleled so that one switch
controls both Page Assigns. Remote control is initiated by setting
the front panel Paging Zone Assign selector to RMT.
e ZR 1 is a 5-wire remote with 2 bits for Zone Program
selection (active low Gray Code), a common shield/ground and
two wires for ratiometric DC control of Zone Level. Zone 1 and
Zone 2 ZR 1 remote ports may be paralleled so that a single re-
mote controls both Zones. Selector logic is active low Gray Code
with pull-up provided in the CP 64S. Control may be a simple
switch closure to ground or 5 volt TTL. Remote control for each
zone is initiated by engaging the RMT switch (located on the
front panel) for that Zone.
Example System: Retail Store
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
PAGE 2 ASSIGN
PAGE 1 ASSIGN
BOTHOFF
BOTH
Z1
OFF
Z2
Z1
Z2
ZR 1
PR 2
SELECT
LEVEL
PROGRAM
ZR 1
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
TELEPHONE HOLD MUSIC
TELEPHONE
PAGE OUT
DISTRIBUTED
MA 4
MULTICHANNEL
AMPLIFIER
DISTRIBUTED OUTPUTS REQUIRE
MT 4 TRANSFORMER ACCESSORY
SELECT
LEVEL
PROGRAM
CD
PLAYER
PRE-RECORDED
ADVERTISEMENT
OR BREAK BELL
DISTRIBUTED STEREO
DVR
62 1:58
MUSIC
SERVICE
ZR 1
ZONE 1 EX2EX1 IN1 IN2Z1LZ1RZ2
ZONE 1 EXPAND 1ZONE 2
ZONE 2
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
OFFICE PAGERETAIL / SHOP FLOOR MEETING / DEMO ROOM
DIGITAL
AMPLIFIER
dB Headroom dB Headroom dB Headroom dB Headroom
3
6
12
24
Limit
1
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
2
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
3
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
4
ON
Comp
Exp
Fault
Load
Ready
MA 4
PRIORITY 1PRIORITY 2
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30 +60
1&2
PRIORITY
321
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–+ –
+
–
+
–
D1 D0 Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2PAGE 1
LIMITERWIRING
ZONE 1 ZONE 2
PAGE
1
TRIM
PAGE
2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30 +60
MIC LINE
–20 +20–20 +20
REMOTES OUTPUTS
MIN MAX
PROGRAM INPUTS
ZONE
2
EXPAND OUT
ZONE
1
EXPAND OUT
ZONE
2
Z2
PGM
Z2
EXPAND
Z2
MONO REMOTE
1
INPUT
1
REMOTE
2
INPUT
2Z1
RIGHT
Z1
EXPAND
Z1
LEFT
Z2
LEVEL
Z1
PGM
Z1
LEVEL
ACN 001 345 482
MIC LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM PGM
PAGE
THIS DEVICE COMPLIES WITH
PA RT 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
Data Sheet-6
CP 64S
COMMERCIAL PROCESSOR
RESTROOMS
EXPAND 2
MUSIC ON HOLD
DISTRIBUTED DISTRIBUTED
DISTRIBUTED
RIGHT
DISTRIBUTED
(USE MT 4
TRANSFORMER
BELOW)
PROMO DVD
12:00
LEFT
PRIORITY 2
PRIORITY 1
OPTIONAL SOURCES
PRIORITY 3
PRIORITY 4
HOLE PLUG
TO SET PAGE
PRIORITY
SUM PAGE 1
& PAGE 2
POST VCA
SET PAGE
PRIORITY
TO P2
EXPAND 1 EMERGENCY PAGE
MASTER
PAGE
PRIORITY 2
SUM PAGE 2
POST VCA
TELEPHONE
KEY SERVICE UNIT
SERVICE WRITER
AND PARTS ROOM
SERVICE BAYS
OFFICES
SALES & CREDIT
SALES FLOOR
SERVICE RECEPTION
RECEPTION
ZR 1 ZR 1
MA 3
MULTICHANNEL
AMPLIFIER
MA 3
MULTICHANNEL
AMPLIFIER
MT 4 MULTICHANNEL TRANSFORMER
ZR 1 ZR 1
PR 2
PR 2
MIC OR
TELEPHONE
PAGE TO
SERVICE
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
PA GE 2 ASSIGN
PA GE 1 ASSIGN
BOTHOFF
BOTH
Z1
OFF
Z2
Z1
Z2
PA GE 1 ASSIGN
BOTHOFF
Z1
Z2
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
ZONE 1 EX2EX1 IN2 IN1Z1LZ1RZ2
EX2 IN1
IN2
Z1LZ2
ZONE 2
ZONE 1ZONE 2
PRIORITY 4
PRIORITY 3
PRIORITY 1PRIORITY 2
MUSIC
SERVICE
CD
10 8:58
CD
10 8:58
6
12
3
12
6
3
00
6
12
3
0
12
dB
MA 3
MULTICHANNEL
AMPLIFIER
3
CHANNEL OUTPUT HEADROOM
POWER
POWER
6
12
3
12
6
3
00
6
12
3
0
12
dB
MA 3
MULTICHANNEL
AMPLIFIER
3
CHANNEL OUTPUT HEADROOM
POWER
POWER
ZONE 2 ZONE 1
ZONE 2 ZONE 1
EXPAND 2
MT 4
MULTICHANNEL
TRANSFORMER
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30 +60
1&2
PRIORITY
321
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–+ –
+
–
+
–
D1 D0 Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2PAGE 1
LIMITERWIRING
ZONE 1 ZONE 2
PAGE
1
TRIM
PAGE
2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30 +60
MIC LINE
–20 +20–20 +20
REMOTES OUTPUTS
MIN MAX
PROGRAM INPUTS
ZONE
2
EXPAND OUT
ZONE
1
EXPAND OUT
ZONE
2
Z2
PGM
Z2
EXPAND
Z2
MONO REMOTE
1
INPUT
1
REMOTE
2
INPUT
2Z1
RIGHT
Z1
EXPAND
Z1
LEFT
Z2
LEVEL
Z1
PGM
Z1
LEVEL
ACN 001 345 482
MIC LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM PGM
PAGE
THIS DEVICE COMPLIES WITH
PA RT 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30 +60
1&2
PRIORITY
321
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–+ –
+
–
+
–
D1 D0 Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2PAGE 1
LIMITERWIRING
ZONE 1 ZONE 2
PAGE
1
TRIM
PAGE
2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30 +60
MIC LINE
–20 +20–20 +20
REMOTES OUTPUTS
MIN MAX
PROGRAM INPUTS
ZONE
2
EXPAND OUT
ZONE
1
EXPAND OUT
ZONE
2
Z2
PGM
Z2
EXPAND
Z2
MONO REMOTE
1
INPUT
1
REMOTE
2
INPUT
2Z1
RIGHT
Z1
EXPAND
Z1
LEFT
Z2
LEVEL
Z1
PGM
Z1
LEVEL
ACN 001 345 482
MIC LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM PGM
PAGE
THIS DEVICE COMPLIES WITH
PA RT 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
CP 64S
COMMERCIAL PROCESSOR
Example System: Auto Dealer and Service
Data Sheet-7
CP 64S
COMMERCIAL PROCESSOR
PR 2
PAGE 2 ASSIGN
PAGE 1 ASSIGN
BOTHOFF
BOTH
Z1
OFF
Z2
Z1
Z2
LEVEL
PROGRAM
SELECT
LEVEL
62 1:58
DVR
PRIORITY 1
KARAOKE DVD
1-1-05
OTHER PROGRAM SOURCE
SATELLITE
AUDIO
MUSIC
SERVICE
SINGER 1
SINGER 2
or ANNOUNCER
or DINING PAGE
PROGRAM
SELECT
PAGE IN
LOUNGE OR
DINING AREA
TRANS-
FORMER
ZR 1
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
ZR 1
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
DINING AREA
KARAOKE LOUNGE
CH 68
MA 4
MULTICHANNEL AMPLIFIER
DIGITAL
AMPLIFIER
dB Headroom dB Headroom dB Headroom dB Headroom
3
6
12
24
Limit
1
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
2
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
3
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
4
ON
Comp
Exp
Fault
Load
Ready
MA 4
ZONE 1 EX2 Z1LZ1RZ2 IN2 IN1ZONE 2
ZONE 1ZONE 2
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30 +60
1&2
PRIORITY
321
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–+ –
+
–
+
–
D1 D0 Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2PAGE 1
LIMITERWIRING
ZONE 1 ZONE 2
PAGE
1
TRIM
PAGE
2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30 +60
MIC LINE
–20 +20–20 +20
REMOTES OUTPUTS
MIN MAX
PROGRAM INPUTS
ZONE
2
EXPAND OUT
ZONE
1
EXPAND OUT
ZONE
2
Z2
PGM
Z2
EXPAND
Z2
MONO REMOTE
1
INPUT
1
REMOTE
2
INPUT
2Z1
RIGHT
Z1
EXPAND
Z1
LEFT
Z2
LEVEL
Z1
PGM
Z1
LEVEL
ACN 001 345 482
MIC LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM PGM
PAGE
THIS DEVICE COMPLIES WITH
PA RT 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
1234
MA 4
MULTICHANNEL AMPLIFIER
ZONE 2
DISTRIBUTED
ZONE 2
EXPAND
DISTRIBUTED
MT 4 70V
TRANSFORMER
JUKEBOX
10 8 19:58
LEVEL
PROGRAM
SELECT
ZONE 1
ZONE 1
EXPAND
DISTRIBUTED
DVR
CH 68
PRIORITY 4
MUSIC
SERVICE
MIC OR
TELEPHONE
PAGE
OFFICE
PAGE
PAGE 2
PR 2
PR 2
HOLE
PLUG
HOLE
PLUG
PAGE
ASSIGN
PRIORITY 3
PAGE 1
PRIORITY 1PRIORITY 2
ZR 1
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
LEVEL
PROGRAM
SELECT
ZR 1
PROGRAM SELECT
LEVEL
82
100
46
L1
L3L2
P
PAGE 2 ASSIGN
PAGE 1 ASSIGN
BOTHOFF
BOTH
Z1
OFF
Z2
Z1
Z2
PAGE 2 ASSIGN
PAGE 1 ASSIGN
BOTHOFF
BOTH
Z1
OFF
Z2
Z1
Z2
PATIO
DINING
DINING ROOM
DISTRIBUTED
LOUNGE
RESTROOMS
OFFICES
CD
10 8:58
RECEPTION
STATION
TELEPHONE
KEY SERVICE
TO TELEPHONE
MUSIC-ON-HOLD
DIGITAL
AMPLIFIER
dB Headroom dB Headroom dB Headroom dB Headroom
3
6
12
24
Limit
1
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
2
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
3
Comp
Exp
Fault
Load
Ready
3
6
12
24
Limit
4
ON
Comp
Exp
Fault
Load
Ready
MA 4
MT 4
MULTICHANNEL
TRANSFORMER
ZONE 1 EX2EX1 IN1 IN2Z1LZ1RZ2ZONE 2
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30 +60
1&2
PRIORITY
321
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–+ –
+
–
+
–
D1 D0 Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2PAGE 1
LIMITERWIRING
ZONE 1 ZONE 2
PAGE
1
TRIM
PAGE
2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30 +60
MIC LINE
–20 +20–20 +20
REMOTES OUTPUTS
MIN MAX
PROGRAM INPUTS
ZONE
2
EXPAND OUT
ZONE
1
EXPAND OUT
ZONE
2
Z2
PGM
Z2
EXPAND
Z2
MONO REMOTE
1
INPUT
1
REMOTE
2
INPUT
2Z1
RIGHT
Z1
EXPAND
Z1
LEFT
Z2
LEVEL
Z1
PGM
Z1
LEVEL
ACN 001 345 482
MIC LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM PGM
PAGE
THIS DEVICE COMPLIES WITH
PA RT 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
Example System: Restaurant
Example System: Karaoke Diner
Data Sheet-8
CP 64S
COMMERCIAL PROCESSOR
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 USA TEL 425-355-6000 FAX 425-347-7757 WEB www.rane.com
CP 64S
COMMERCIAL PROCESSOR
Rear Panel
All features & specications subject to change without notice. DOC 102906
Architectural Specifications
e processor shall provide two fully independent gated paging
inputs, three line-level non-priority program inputs and one
gated line-level priority program input. Two zone outputs shall
be served. Zone 1 shall be a stereo zone with balanced, cross-
coupled outputs. Zone 2 shall be a mono zone with a balanced
cross-coupled output. Mono expansion ports for page, program
or zone signals shall be provided for each zone. Wired remote
control ports shall be provided for paging zone assign, zone
program select and zone level.
Page inputs shall use a 5-pin Euroblock connector. Paging
controls shall include:
• 30 dB mic/line input pad.
• Input gain trim range of 30 dB to 60 dB.
• Mic gate threshold (range -∞ to +4 dBu).
• 15 volt phantom power (internal switch).
• Paging priority (page 1, none, page 2; internal switch).
• Pre- or post-zone level summing (internal switch).
• Front panel paging zone assign (Remote, Z1, Z2, Both).
• Remote paging zone assign (O, Z1, Z2, Both).
• Paging zone level.
Each Program input shall have stereo RCA input jacks and
independent input level control. e priority program assign
switch shall provide priority program override to zone 1, zone 2,
both, or neither (o). e gated priority program input shall
have internally adjustable threshold and release time controls.
Zone outputs shall use 3-pin Euroblock connectors. Zone
controls shall include:
• Ducker on/o
• Ducker depth (-6 to -50 dB)
• Program select (L1, L2, L3, P)
• Zone level
• 7-band graphic equalizer (±12 dB)
• Servo-Locked-Limiter
™
threshold (-20 to +20 dBu)
• Mono switch for Zone 1 (internal)
• Remote engage switch
Wired remote ports shall use 3-pin Euroblock connectors.
Remote logic shall be active low with internal pull-up. Remote
level control shall be ratiometric DC control with 5 volt
reference.
e unit shall be capable of operation by means of its own
built-in universal power supply operating at 100-240 VAC and
meet CE requirements. e unit shall be UL and cUL listed. e
unit shall be entirely constructed from cold-rolled steel.
Reliability and efficiency are to be primary design consider-
ations.
e unit shall be a Rane Corporation CP 64S Commercial
Processor.
Available Accessories
• SCP 2S Security Cover (for EQ section)
• SC 1.7 Security Cover (for entire front panel)
• PR 2 Page Assign Remote Control
• ZR 1 Zone Source/Volume Remote Control
• Hole Plugs (6 Provided with SCP 2S)
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30 +60
1&2
PRIORITY
321
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–+ –
+
–
+
–
D1 D0 Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2PAGE 1
LIMITERWIRING
ZONE 1 ZONE 2
PAGE
1
TRIM
PAGE
2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30 +60
MIC LINE
–20 +20–20 +20
REMOTES OUTPUTS
MIN MAX
PROGRAM INPUTS
ZONE
2
EXPAND OUT
ZONE
1
EXPAND OUT
ZONE
2
Z2
PGM
Z2
EXPAND
Z2
MONO REMOTE
1
INPUT
1
REMOTE
2
INPUT
2Z1
RIGHT
Z1
EXPAND
Z1
LEFT
Z2
LEVEL
Z1
PGM
Z1
LEVEL
ACN 001 345 482
MIC LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM PGM
PAGE
THIS DEVICE COMPLIES WITH
PA RT 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
Euroblocks are included, removed here for label visibility.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Rane 64S User manual

Rane
Brand
Rane
Model
64S
Category
Audio equalizers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents