Christie FHD651-T User manual

FHD651-P and FHD651-T LCD

Panels

User Manual

020-000693-01

FHD651-P and FHD651-T LCD

Panels

User Manual

020-000693-01

NOTICES

COPYRIGHT AND TRADEMARKS

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial

environment. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of the product in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at the user’s own expense.

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서

사용하는 것을 목적으로 합니다 .

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may

not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance

specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in

proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no

warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.

Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or

use of this material.

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol

means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please

dispose of the product appropriately and according to local regulations. In the European Union, there are separate collection systems

for used electrical and electronic products. Please help us to conserve the environment we live in.

Canadian manufacturing facility is ISO 9001 and 14001 certified.

GENERAL WARRANTY STATEMENTS

For complete information about Christie’s limited warranty, see the Christie website (www.christiedigital.com) or contact your Christie

dealer. In addition to the limitations that may be specified in Christie’s limited warranty, the warranty does not cover:

a. Problems or damage occurring during shipment, in either direction.

b. Projector lamps (See Christie’s separate lamp program policy).

c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp supplied by a

supplier other than Christie or an authorized distributor of Christie lamps.

d. Problems or damage caused by combination of a Product with non-Christie equipment, such as distribution systems, cameras,

DVD players, etc., or use of a Product with any non-Christie interface device.

e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an

unauthorized distributor of Christie lamps, replacement parts or components including, without limitation, any distributor offering

Christie lamps, replacement parts or components through the internet (confirmation of authorized distributors may be obtained

from Christie).

f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other natural

disaster.

g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service

personnel or a Christie authorized repair service provider.

h. Problems or damage caused by use of a Product on a motion platform or other movable device where such Product has not been

designed, modified or approved by Christie for such use.

i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is

unrelated to the projector.

j. For LCD projectors, the warranty period applies only where the LCD projector is in “normal use.” “Normal use” means the LCD

projector is not used more than 8 hours a day, 5 days a week.

k. Except where the Product is designed for outdoor use, problems or damage caused by use of the Product outdoors unless (i) such

Product is protected from precipitation or other adverse weather or environmental conditions and the ambient temperature is

within the recommended ambient temperature set forth in the specifications for such Product and (ii) if the Product is an LCD flat

panel, such LCD flat panel is not exposed to direct sunlight.

l. Image retention on LCD flat panels.

m.Defects caused by normal wear and tear or otherwise due to normal aging of a Product.

n. Products where the serial number has been removed or obliterated.

o. Products sold by a Reseller to an End User outside of the country where the Reseller is located unless (i) Christie has an office in

the country where the End User is located or (ii) the required international warranty fee has been paid.

p. Products when there is failure to perform maintenance as required and in accordance with the maintenance schedule.

q. This warranty does not obligate Christie to provide any on site warranty service at the Product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance

section for specific maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance

with the maintenance schedule specified by Christie, will void the warranty.

Addendum

Translated copies of this document are provided on the CD in the back of this document. The CD may also

contain additional product documentation. Read all instructions before using or servicing this product.

本文档的翻译副本在本文档背面的CD上提供。该CD中还可能包含其他产品文

档。使用或维修本产品之前请务必阅读所有说明。

文件背面的光碟提供了本文件的翻譯副本。這張光碟可能另外包含其他產品文件。

請先閱讀所有指示再使用或送修本產品。

LeCDaudosdecedocumentcontientdestraductionsdecelui‐cidansdifférenteslangues.CeCDpeutégalement

contenirdeladocumentationsupplémentairesurleproduit.Liseztouteslesinstructionsavantd'utiliserou

d'entretenirceproduit.

Übersetzte Versionen dieses Dokuments werden auf der CD auf dem Vorsatzblatt dieses Dokuments

bereitgestellt. Die CD kann auch zusätzliche Produktdokumentation enthalten. Bitte lesen Sie diese

Anweisungen vor der Verwendung dieses Produkts oder vor der Ausführung von Wartungsarbeiten am

Produkt.

Le copie tradotte di questo documento sono fornite sul CD, sul retro di questo documento. Il CD

potrebbe anche contenere altra documentazione sul prodotto. Si prega di leggere tutte le istruzioni

prima di utilizzare questo prodotto o sottoporlo a manutenzione.

このドキュメントの翻訳版がこのドキュメントの裏面の CD で提供されています。CD に

は追加の製品マニュアルも収められています。この製品を使用したり、機能させたりする

前に、すべての指示をお読みください。

이문서의번역된 사본이이 문서후면의CD 에서제공됩니다 . 이CD 에는추가제품설명서

가 포함되어있을 수 있습니다 .이 제품을 사용하거나 수리하기 전에 모든 지침을 확인하

십시오 .

Copias traduzidas deste documento são fornecida no CD contido na parte de trás deste documento. O

CD pode conter documentação adicional do produto. Leia todas as instruções antes de usar ou prestar

serviço com este produto.

Переводданногодокументапредставленнакомпакт-дискенаоборотнойстороне

документа.Компакт-дискможеттакжесодержатьдополнительнуюдокументациюпо

продукту.Передиспользованиемилиобслуживаниемпродуктаознакомьтесьсовсеми

инструкциями.

Las copias traducidas de este documento se proporcionan en el CD que se encuentra en la parte trasera.

En el CD también puede encontrar documentación adicional del producto. Lea todas las instrucciones

antes de utilizar o realizar el mantenimiento de este producto.

Перекладеніекземплярицьогодокументамістятьсянакомпакт- диску,якийдоданодо

цьогодокумента.Накомпакт-дискуможетакожбутидодатковадокументаціядо

виробу.Першніжкористуватисявиробомабойогообслуговувати,прочитайтевсі

інструкції.

FHD651-P and FHD651-T LCD Panels User Manual i

020-000693-01 Rev. 1 (02-2014)

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Target Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Textual and Graphic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Description, Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Key Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Display at a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Input Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Locking and Unlocking the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Ambient Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Ambient Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Ventilation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Mounting the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Connections to the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Connecting a Control System or PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

IR Extender Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Connecting Source Components to the Display . . . . . . . . . . . . . . . . . . . . . . . . . .14

Turning on the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Changing the OSD Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Enabling the Touch Screen (FHD651-T Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Connecting the Touch Screen Controller Host Computer to the Display . . . . . . . . . .18

Installing TouchWin Software (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Touch Screen Configuration Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the On-Screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

ii FHD651-P and FHD651-T LCD Panels User Manual

020-000693-01 Rev. 1 (02-2014)

Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Maintenance and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

RS232 Connection and Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Command and Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Command and Response Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Serial Command List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Using Discrete IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

IR Command Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

IR Control Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Ethernet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Supported Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

FHD651-T Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

FHD651-P Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

FHD651-P and FHD651-T LCD Panels User Manual 1

020-000693-01 Rev. 1 (02-2014)

Introduction

About This Manual

This Owner’s Manual describes how to install, set up and operate the FHD651-P and FHD651-T LCD

Panels.

Throughout this manual, the FHD651-P and FHD651-T LCD Panels are referred to collectively as the

“display.”

Target Audience

The manufacturer has prepared this manual to help end users get the most out of the display.

The manufacturer has made every effort to ensure that this manual is accurate as of the date it was

printed. However, because of ongoing product improvements and customer feedback, it may require

updating from time to time.

Textual and Graphic Conventions

Text Conventions

The following conventions are used in this manual, in order to clarify the information and instructions

provided:

• Remote and built-in keypad button identifiers are set in upper-case bold type; for example,

“Press EXIT to return to the previous menu.”

• Computer input (commands you type) and output (responses that appear on-screen) is shown in

monospace (fixed-width) type; for example: “To change the aspect ratio to Letterbox, type

07 00 02 41 53 50 03 08 <Enter>.”

• All keys with functional names are initial-capped, set in bold type and enclosed in angle brackets.

These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc> and <Tab>.

• <Enter> indicates that you may press either the RETURN or ENTER key on your keyboard if it has

both keys.

In addition to these conventions, underlining, boldface and/or italics are occasionally used to

highlight important information.

i

A carriage return must be used after each command or string.

2 FHD651-P and FHD651-T LCD Panels User Manual

020-000693-01 Rev. 1 (02-2014)

Introduction

Description, Features and Benefits

The FHD651-P and FHD651-T LCD Panels represent the cutting edge of direct-view LCD technology.

They combine ultra-high resolution and unparalleled image quality with configurable I/O in a large-

format display for a wide range of digital signage and control-room applications.

Key Features and Benefits

The display offers these key features and benefits:

• Full-HD Native Resolution: 1920 x 1080 (16:9 Native Aspect Ratio)

• High Brightness: Up to 360 nits

• Ultra-wide 178-degree Viewing Angle

• DisplayPort 1.1a, HDMI and DVI Inputs with High-bandwidth Digital Content Protection (HDCP)

• Direct LED Backlight with active ambient light sensor to adjust backlight automatically

• Touch Capability (FHD651-T only):

• Precise, highly responsive touch technology

• High touch sensitivity – no pressure required

• Any touch: finger, gloved hand or pointer

• One-time, nine-point calibration with no drift

• Windows 7/8 compliant

• USB: one cable for power and communications

• Supports landscape and portrait orientations

Parts List

Your display is shipped with the following items. If any items are missing or damaged, please contact

your dealer or Customer Service.

• FHD651-P or FHD651-T LCD Panel

• Remote Control Unit and batteries

•VGA Cable

•DVI Cable

• RS232 Cable

•IR Extender

• USB Cable (FHD651-T only)

FHD651-P and FHD651-T LCD Panels User Manual 3

020-000693-01 Rev. 1 (02-2014)

Controls and Functions

Display at a Glance

The illustration below shows the key display components, and the paragraphs that follow describe

them.

1. MAIN POWER SWITCH

Connects or disconnects the display panel from the AC power source.

2. STATUS LED

Lights orange to indicate that the display is in standby mode; blinks orange if no input signal is

present; off if the main power switch is set to off.

SOURCE

MENU/EXIT

3

2

1

4 FHD651-P and FHD651-T LCD Panels User Manual

020-000693-01 Rev. 1 (02-2014)

Controls and Functions

3. KEYPAD

You can use the keypad instead of the remote control unit to operate the

on-screen display (OSD) controls. The keypad operates as follows:



On/Standby ( )



Press once to toggle from standby mode to on mode. Press it again to

return to standby mode. 



SOURCE

To select a source, press the SOURCE button repeatedly (with no menus

visible on-screen). 



When a menu is visible on-screen, this button operates identically to the

right-arrow (or ENTER) button on the display remote control unit. 



When a menu is visible on-screen, this button operates identically to the

left-arrow button on the display remote control unit.



/ 

When a menu is visible on-screen, these buttons operate identically to the

up- and down-arrow buttons on the display remote control unit.



MENU/EXIT

Press this button to access the on-screen display (OSD) controls, or to exit

the current menu and return to the previous one.

SOURCE

MENU/EXIT

Controls and Functions

FHD651-P and FHD651-T LCD Panels User Manual 5

020-000693-01 Rev. 1 (02-2014)

Input Panel

The illustration below shows the display input panel.

1. Power Input (100 to 240 VAC)

Connect the display to power here.

2. USB (Touch Model only)

A standard, Type B USB port for connecting the Multi-Touch Controller host computer to the

display.

3. RS232C In

A female, 9-pin D-sub connector for interfacing with a PC or control system.

4. Ethernet

A female, RJ45 connector for interfacing with a PC or control system over a local area network.

2

3

8

6

7

10

4

5

9

1

11

6 FHD651-P and FHD651-T LCD Panels User Manual

020-000693-01 Rev. 1 (02-2014)

Controls and Functions

5. DisplayPort

DisplayPort 1.1a and DisplayPort-HDCP 1.1 compliant, SD/HD input for connecting SDTV, EDTV or

HDTV component video sources.

6. HDMI 

HDCP-compliant digital video input for connecting HDMI or DVI sources.

7. DVI-D In (HDCP-compliant)

VESA-standard digital video input from a personal computer, or digital video from a DVD player

or HD set-top box.

8. VGA In (15-pin D-Sub)

For connecting components that have RGB or component output jacks such as a personal

computer or external DTV decoder (a break-out cable is needed for BNC-type connection).

9. PC Audio In 

Connect the audio output from a personal computer here.

10. IR Extender

Connect the IR Extender cable provided with the display to this input.

11. Audio Out 

For connecting external, powered speakers or an external audio receiver/amplifier.

Controls and Functions

FHD651-P and FHD651-T LCD Panels User Manual 7

020-000693-01 Rev. 1 (02-2014)

Remote Control Unit

The illustration below shows the display remote control, and the table that follows describes its

functionality.

2

4

6

1

3

5

9

7

10

8

8 FHD651-P and FHD651-T LCD Panels User Manual

020-000693-01 Rev. 1 (02-2014)

Controls and Functions

Label Description

1 Turns the monitor on and off

2 INFO Provides source and resolution information

3 VGA Selects the PC RGB source

DVI Selects the PC DVI source

HDMI1 Selects the HDMI source

COMP (no function)

AV

HDMI2

4P-POSITION

DISPLAYPORT Select the DisplayPort source

PIP (no function)

S-V

5P-SOURCE

6SWAP

7 MENU Opens the monitor’s on-screen menu system. When the menu system is

already open, pressing this button will select the previous submenu

, , ,

Navigates through submenus and settings

8 ENTER Selects highlighted menu choices

9 EXIT Closes the menu system

10 SCALING Selects each aspect ratio, in sequence: Full Screen, Pillar Box and Auto

FREEZE (no function)

MUTE Turns off the sound

BRIGHT Adjusts the brightness

CONTRAST Adjusts the contrast

AUTO Auto adjustment of VGA source

SOURCE Selects each source, in sequence

VOLUME- Decreases the sound volume

VOLUME+ Increases the sound volume

FHD651-P and FHD651-T LCD Panels User Manual 9

020-000693-01 Rev. 1 (02-2014)

Installation

Remote Control

To install batteries in the remote control:

1. Press down the tab on the cover and pull the cover up.

2. Insert the included batteries. Ensure that the polarities correctly match the and markings

inside the battery compartment.

3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in

place.

Notes on Batteries

• Make sure that the battery polarities are correct when installing the batteries.

• Do not mix an old battery with a new one or different types of batteries.

• If you will not use the remote control for a long time, remove the batteries to avoid damage from

battery leakage.

• Do not expose batteries to excessive heat such as from sunshine, fire or the like.

Notes on Remote Control Operation

• Make sure that there is nothing obstructing the infrared beam between the remote control and

the IR receiver on the display.

• If the effective range of the remote control decreases, or it stops working, replace the batteries

with new ones.

• The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight

or fluorescent lighting.

• Ambient conditions may possibly impede the operation of the remote control. If this happens,

point the remote control at the display, and repeat the operation.

Locking and Unlocking the Remote Control

You can lock the remote control buttons to prevent unauthorized persons from changing settings on

the display. To do this, press ENTER, ENTER, EXIT, EXIT, ENTER and EXIT, in sequence. To unlock

a locked remote control unit, use the same sequence of button presses.

Installation must be performed by a qualified custom video installation specialist.

10 FHD651-P and FHD651-T LCD Panels User Manual

020-000693-01 Rev. 1 (02-2014)

Installation

Quick Setup

Here is a quick overview of the display installation process. The sections following this one provide

detailed instructions.

Installation Considerations

Proper installation of your display will ensure a satisfying viewing experience. Whether you are

installing a display temporarily or permanently, you should take the following into account to ensure

your display performs optimally.

Ambient Light

In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your images

will be noticeably reduced if light directly strikes the screen, such as when a shaft of light from a

window or floodlight falls on the image. Images may then appear washed out and less vibrant.

Ambient Heat

Keep the ambient temperature constant and below 35°C (95°F). Keep the display away from heating

and/or air conditioning vents.

Step Procedure For Details, Refer to

page...

1 Mount the display(s) on a wall (optional) 11

2 Connect other external equipment to the display (optional):

• Automation/control system (RS232 or Ethernet)

• IR extender

12

14

3 Connect signal sources to the display 14

4 Apply power to the display 17

5 Change the OSD language (optional) 17

6 Perform touch screen-specific installation and configuration tasks (touch

model only):

• Connect touch screen controller host computer to the display

• Install TouchWin software (optional)

• Use TouchWin to configure touch screen engine and calibrate display

18

20

7 Display calibration: adjust the following for each input:

• Aspect ratio • Color level

• Brightness • Tint

• Contrast • Input position

• Color temperature and white balance

23

Installation

FHD651-P and FHD651-T LCD Panels User Manual 11

020-000693-01 Rev. 1 (02-2014)

Ventilation Considerations

If you are mounting the display in an enclosure, leave sufficient space on all sides between it and

surrounding objects, as shown below. This allows heat to disperse, maintaining the proper operating

temperature.

Mounting the Display

You can mount the display on a wall. See FHD651-T Dimensions on page 53 for mounting hole

locations.

If you do decide to wall-mount the display, ensure that the wall-mount bracket is installed according

to the instructions included with it. The wall must be capable of supporting a redundant weight factor

three (3) times the weight of the display, or be reinforced.

We recommend that this be done by a custom installation specialist.

Connections to the Display

Proceed as follows to connect the display to your video sources, external controller(s) – if present –

and AC power.

Use only the approved wall-mount kit designed for your display.

Wall

50 mm (2

"

)50 mm (2

"

)

50 mm (2

"

)50 mm (2

"

)

8 mm (0.33

"

)

12 FHD651-P and FHD651-T LCD Panels User Manual

020-000693-01 Rev. 1 (02-2014)

Installation

When connecting your equipment:

• Turn off all equipment before making any connections.

• Use the correct signal cables for each source.

• For best performance and to minimize cable clutter, use high-quality cables that are only as long

as necessary to connect two devices. (Don’t use a 20-foot cable when a 6-foot cable will suffice.)

• Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have

them.

Connecting a Control System or PC

RS232 Connection

Use a straight-through RS232 cable with a 9-pin male connector to connect a PC or control/

automation system (if present) to the RS232 port on the display. For more information about using

this connection, refer to External Control on page 39.

to Automation/

Control System

or PC

2 Receive Data

(to ctrl. system)

3 Transmit Data

(from ctrl. system)

5 Ground

1

2

345

7

89

6

Page is loading ...

Christie FHD651-T User manual

This manual is also suitable for

Christie FHD651-T User manual

Related papers

Other documents