2. Cash Valve
  3. PBE-1 Mini Repair Kit

Cash Valve PBE-1 Mini Repair Kit Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Cash Valve PBE-1 Mini Repair Kit Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Pressure Spring
Spring Chamber
Lock Nut
Adjusting Screw
Seat Ring
Step Must
Face Up.
Assembly
Gasket
Fig. 1a
Fig. 1b
Body
Fig. 1
Diaphragm
Diaphragm
Assembly
Diaphragm
Fig. 2
Diaphragm Assembly Nut
Washer
Pressure Plate
Diaphragms
Ball Seat Gasket
Ball Seat
Pressure Spring
Spring Chamber
Lock Nut
Adjusting Screw
Seat Ring
Step Must
Face Up.
Assembly
Gasket
Fig. 1a
Fig. 1b
Body
Fig. 1
Diaphragm
Diaphragm
Assembly
Diaphragm
Fig. 2
Diaphragm Assembly Nut
Washer
Pressure Plate
Diaphragms
Ball Seat Gasket
Ball Seat
CASH PBE-1 MINI REPAIR KIT
INSTALLATION INSTRUCTIONS
Before installation, these instructions must be fully read and understood.
INSTALLATION
1. Loosen Lock Nut 1/4 turn and loosen
Adjusting Screw until the Pressure Spring is
no longer under tension. - see Fig. 1.
IMPORTANT
Exercise care to ensure that the rounded surface of
the Ball Seat is not scratched, marred or damaged
during disassembly and re-assembly.
3. Reassemble Diaphragm Assembly with Ball
Seat Gasket and Diaphragms included in
Kit. Tighten Diaphragm Assembly Nut to
25in-lbs. torque.
4. Before reinstalling Diaphragm Assembly,
ensure that Seat Ring is installed with the
step facing up – see Fig. 1b. Position the
Diaphragm Gasket between the Body and
Diaphragm Assembly – see Fig 1a.
5. Reassemble remaining components. Tighten
Spring Chamber to 90 ft-lbs. torque.
FIGURE 1
FIGURE 2
Emerson.com/FinalControl © 2018 Emerson. All rights reserved. VCIOM-10772-EN 18/11
NOTE
When installing the Adjusting Screw during re-
assembly, tighten the screw until the Lock Nut just
touches the Spring Chamber. When the Valve is
placed in service the pressure setting should be very
close to the original setting.
2. Loosen and remove Spring Chamber and
remove Diaphragm Assembly. Loosen
and remove Diaphragm Assembly Nut
and remove Washer, Pressure Plate,
Diaphragms and Ball Seat Gasket – see
Fig2.
2
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product.
Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Cash is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson
andthe Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by
our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without
notice.
Emerson.com/FinalControl
/