T
ABLE OF
C
ONTENTS
English………………………………………………………………………………1
Package Contents…………………………………………………………………………1
System Requirements……………………………………………………………………1
Factory Default Settings…………………………………………………………………1
Know Your ZPW4000………………………………………………………………………2
Application……………………………………………………………………………………3
Hardware Installation……………………………………………………………………4
Software Installation……………………………………………………………………5
Configure Your Computer……………………………………………………………13
TroubleShooting……………………………………………………………………………17
Español………………………………………………………………………………18
Contenido del Paquete…………………………………………………………………18
Requerimientos del Sistema…………………………………………………………18
Reestablecer a configuración de Fábrica………………………………………18
Conoce tu ZPW4000……………………………………………………………………19
Aplicación……………………………………………………………………………………20
Instalación del Hardware……………………………………………………………21
Instalación del Software………………………………………………………………22
Configura tu Computadora…………………………………………………………30
Solución de Problemas…………………………………………………………………34
1
Package Contents
ZPW4000
Installation CD
Quick Installation Guide
Power Adapter
System Requirements
Windows 2000, XP, Vista, 7; Macintosh 8.1 or above; Linux
A CD-ROM Drive
TCP/IP protocol must be installed on each PC
Internet connection, provided by xDSL or cable modem with a
RJ-45 Ethernet port.
Computer or network devices with wired or wireless network
interface card.
Web browser (Microsoft Internet Explorer 6.0 or above,
Firefox 3.0 or above; Safari 3.2.3 or above).
One USB printer(non-GDI/CAPT)
One USB printer cable
An available power socket (100–240V, 50/60Hz)
Factory Default Settings
Item Default Value
Password None (Leave it blank)
Wireless Mode Ad-Hoc (Peer-to-Peer)
Channel 6
SSID WLAN-PS
IP Address 192.168.0.10
Subnet Mask 255.255.255.0
2
Know Your ZPW4000
Front Side
Item Name
Descripti
on
5V2A Power Connector, connects to power adapter
ON ZPW4000 is switched on and correctly powered
Status LED
Flashing ZPW4000 is processing Power On Self Test (POST)
USB LED ON USB port is connected
USB Port Connect to USB Printer
10/100Mbps Local Area Network (LAN) port
Rear Side
Item Name
Description
ON ZPW4000 is wireless connected.
WLAN LED
Flashing
ZPW4000 is transferring or receiving data wirelessly.
WPS Button Press this button for 3 seconds to start WPS function.
Press this button for 1 second to Reboot ZPW4000.
Reset Button
Turn off ZPW4000 and press this button then hold for 7
seconds
after turning on ZPW4000 to restore all settings to factory
defaults.
3
Application
a. Wired Connection with ZPW4000
b. Wireless Connection with ZPW4000
Default: Ad-Hoc Mode (Peer-to-Peer)
Infrastructure mode
4
Hardware Installation
1. Turn off the printer’s power.
2. Connect ZPW4000 to your
printer with the supplied printer
cable.
3. Turn on the printer’s power.
4. Connect the power adapter to
the wall socket, and then
connect it to the “Power” socket
of ZPW4000.
5. Wait for 10 seconds as part of
the ZPW4000’s Power On Self
Test (POST)
5
Software Installation
Note 1: To enable network communication with ZPW4000, your computer
must have a proper IP address as 192.168.0.X (X is from 11 to
253)
Note 2: To change the setting after software installation, runs Setup
Wizard as administrator under Windows Vista & 7 by right-click
PSWizard icon on desktop.
1. Insert the setup CD into your
CD-drive, and choose Setup
Wizard to install ZPW4000 and
configure the connected printer.
2. Click Next, the wizard will
automatically discover ZPW4000.
6
3. From the Select A Print Server
screen, select ZPW4000 to
configure and click Next.
4-1-1. On the Change Settings
screen, click Yes if you want to
change wireless settings or
assign a static IP address to
ZPW4000 and then click Next.
Password: Leave it blank
4-1-2. On the Basic Wireless
Settings screen, configure
wireless settings from
drop-down menu and then click
Next.
Communication Type
SSID: WLAN-PS by default
Channel: Optional
Data Transfer Rate
Transmit Mode
7
4-1-3. On the Wireless Security
screen, configure security
features from drop-down menu
according to your wireless
network and then click Next.
4-1-4. On the TCP/IP Settings
screen, specify a fixed or
dynamic IP address for
ZPW4000 and then click Next.
4-2. Click No if you want ZPW4000
keep using the default IP
address and default settings,
and then click Next.
Password: None
Communication Type: Ad-Hoc
Channel: 6
SSID: WLAN-PS
Encryption: None
DHCP Client: Off
IP address: 192.168.0.10
Subnet Mask: 255.255.255.0
Note: The IP address of print server must be within the
same subnet as your wireless adapter.
8
5-1. On the Select A Printer screen,
select an already configured
printer from the list, click Next →
Next → Finish to complete the
installation.
5-2-1. or Click Add New Printer
button if ZPW4000 is connected to
a printer that hasn’t been installed
before and does not appear in the
list.
5-2-2. Click Next to continue.
9
5-2-3. Select Local Printer, make
sure Automatically detect and
install my Plug and Play
printer check box is NOT
checked. Then click Next.
5-2-4. Make sure the Use the
following port radio-button is
clicked and select LPT1:
(Recommended Printer Port)
from the pull-down list. Then click
Next.
5-2-5. Select Manufacturer and
Printer from the lists of printer’s
driver. Then click Next.
10
5-2-6. If you already have the
printer’s driver installed, you will
be asked whether to keep it or to
replace it. Click Next.
5-2-7. Supply a name for the printer
and choose whether you want to
make it your default printer.
Then click Next.
5-2-8. Select No to not to print a test
page and click Next → Finish.
11
5-2-9. Back to setup wizard, finish
the installation by highlighting
the installed printer in Select a
Printer page and click Next →
Next → Finish.
6. From Windows system, go to start
→ Printers and Faxes then
right-click your newly installed
printer and select Properties
7. Go to Ports tab and verify
ZPW4000’s port appears.
12
8. Go to General tab and click Print
Test Page to verify the
configuration.
Your printer now is ready to use with ZPW4000.
Note: If you wish to install more print servers, start setup
wizard by right-click PSWizard icon on desktop or
from your Windows Start menu: start
→
All
Programs
→
802.11n Wireless Print Server
→
PSWzard and repeat the installation procedure.
13
Configure Your Computer
a. Ad-Hoc Mode:
1. Click Start →
→→
→ Control Panel →
→→
→
Network and Internet.
2. Click Network and Sharing
Center.
3. Click Local Area Connection
and then Local Area Connection
Status window will pop-out.
14
4. Click Properties from Local
Area Connection Status.
5. Select Internet Protocol
Version 4 (TCP/IPv4) and
click Properties.
15
6. Specify a proper IP address for
your wireless adapter by selecting
Use the following IP address
and enter the IP address as
192.168.0.X (X is from 11 to 253).
Of course, you need to input the
DNS server address provided by
your ISP. Click OK to save the
configurations.
7. Double click the wireless network
icon on the system tray to
check the wireless network,
choose ZPW4000 (WLAN-PS) and
click Connect to setup the
association.
16
b. Infrastructure Mode:
1. Press WPS buttons of ZPW4000
and Wireless AP in 3(three)
seconds then release, and then
the WLAN LED of ZPW4000 will be
off.
2. Wait 2(two) minutes until WLAN
LED of ZPW4000 light again for
finding wireless AP WPS
activated. Then, ZPW4000 and
Wireless AP complete a secured
wireless connection.
Please refer to
User Manual
for more details and other settings.
17
TroubleShooting
Q1. How to create ZPW4000 port manually?
1. From Windows System, go to Start → All Programs →
Accessories → System Tools → Control Panel → Hardware
and Sound → Printers.
2. Find your installed printer icon, right-click and then select
Properties → Ports tab → Add Port → Standard TCP/IP Port
→ New Port → Next.
3. Input the exact IP address of print server that you configured it.
Click Next.
4. Select Custom, and click Settings.
5. Choose LPR, and input the queue name as lp1.
6. Click OK → Next → Finish, to complete the wizard.
7. Click Close → Apply.
8. Now, the ZPW4000 port has been created.
Q2. How to know the current settings of ZPW4000?
1. Plug the power adapter into the power connector on ZPW4000.
2. Wait 10 seconds as part of the ZPW4000’s Power On Self Test
(POST).
3. Press the reset button for 8 seconds, and then release it.
4. Then, the test page includes the current settings of ZPW4000 will
be printed out.
18
Contenido del Paquete
ZPW4000
CD de Instalación
Guía Rápida de Instalación
Adaptador de corriente
Requerimientos Del Sistema
Windows 2000, XP, Vista, 7; Macintosh 8.1 o superior; Linux
Unidad de CD-ROM
Protocolo TCP/IP debe estar instalado en cada PC
Conexión a Internet, proporcionada por módem x DSL o cable
con un puerto Ethernet RJ-45.
PC o dispositivos de red con cable o tarjeta de interfaz de red
inalámbrica.
Web browser (Microsoft Internet Explorer 6.0 o superior,
Firefox 3.0 o superior; Safari 3.2.3 o superior).
Una impresora USB (No-GDI/CAPT)
Un Cable para impresora USB
Una toma de corriente disponible (100–240V, 50/60Hz)
Configuración de Fábrica
Item Valores default
Password No (Dejar en blanco)
Modo Wireless Ad-Hoc (Peer-to-Peer)
Canal 6
SSID WLAN-PS
Dirección IP 192.168.0.10
Mascara Sub red 255.255.255.0
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
