Xerox Regal 5790 Installation guide

Getting Started

FIERY X2

This publication is protected by copyright, and all rights are reserved. No part of it may be reproduced or transmitted in any form or by any means for any purpose

without express prior written consent from Electronics for Imaging, Inc., except as expressly permitted herein. Information in this document is subject to change

without notice and does not represent a commitment on the part of Electronics for Imaging, Inc.

The software described in this publication is furnished under license and may only be used or copied in accordance with the terms of such license.

Patents: 5,666,436; 5,553,200; 5,543,940; 5,537,516; 5,517,334; 5,506,946; 5,424,754; 5,343,311; 5,212,546; 4,941,038; 4,837,722; 4,500,919

Trademarks

EFI, the EFI logo, Fiery, the Fiery logo, EFICOLOR, and Rip-While-Print are trademarks registered in the U.S. Patent and Trademark Ofﬁce. Fiery ZX, Fiery X2,

Fiery Driven, the Fiery Driven logo, Command WorkStation, AutoCal, Starr Compression, Memory Multiplier, ColorWise, NetWise, and VisualCal are

trademarks of Electronics for Imaging, Inc.

All Xerox product names mentioned in this publication are trademarks of the XEROX CORPORATION.

Adobe, the Adobe logo, Adobe Illustrator, PostScript, Adobe Photoshop, Adobe Separator, and Adobe PageMaker are trademarks of Adobe Systems Incorporated,

registered in certain jurisdictions. EPS (Encapsulated PostScript) is a trademark of Altsys Corporation. Apple, the Apple logo, AppleShare, AppleTalk, EtherTalk,

LaserWriter, and Macintosh are registered trademarks, and MultiFinder is a trademark of Apple Computer, Inc. Microsoft, MS, MS-DOS, and Windows are

registered trademarks of Microsoft in the US and other countries. QuarkXPress is a registered trademark of Quark, Inc. Times, Helvetica, and Palatino are

trademarks of Linotype AG and/or its subsidiaries. ITC Avant Garde, ITC Bookman, ITC Zapf Chancery, and ITC Zapf Dingbats are registered trademarks of

International Typeface Corporation. Ethernet is a registered trademark of Xerox Corporation. Farallon, PhoneNET PC, and PhoneNET Talk are trademarks of

Farallon Computing, Inc. COPS and COPSTalk are trademarks of CoOperative Printing Solutions, Inc. NetWare and Novell are registered trademarks and

Internetwork Packet Exchange (IPX) is a trademark of Novell, Inc. SyQuest is a registered trademark, in the United States and certain other countries, of SyQuest

Technology, Inc. UNIX is a registered trademark of UNIX System Laboratories, a wholly owned subsidiary of Novell, Inc. PANTONE is a registered trademark

of Pantone, Inc.

All other terms and product names may be trademarks or registered trademarks of their respective owners, and are hereby acknowledged.

Legal Notices

APPLE COMPUTER, INC. (“APPLE”) MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE APPLE SOFTWARE.

APPLE DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE

OF THE APPLE SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY, RELIABILITY, CURRENTNESS, OR OTHERWISE. THE ENTIRE

RISK AS TO THE RESULTS AND PERFORMANCE OF THE APPLE SOFTWARE IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED

WARRANTIES IS NOT PERMITTED BY SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.

IN NO EVENT WILL APPLE, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL,

INCIDENTAL OR INDIRECT DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF

BUSINESS INFORMATION, AND THE LIKE) ARISING OUT OF THE USE OR INABILITY TO USE THE APPLE SOFTWARE EVEN IF APPLE

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

Apple’s liability to you for actual damages from any cause whatsoever, and regardless of the form of the action (whether in contract, tort [including negligence],

product liability or otherwise), will be limited to $50.

Restricted Rights Legends

For defense agencies: Restricted Rights Legend. Use, reproduction, or disclosure is subject to restrictions set forth in subparagraph (c)(1)(ii) of the Rights in

Technical Data and Computer Software clause at 252.227.7013.

For civilian agencies: Restricted Rights Legend. Use, reproduction, or disclosure is subject to restrictions set forth in subparagraph (a) through (d) of the

commercial Computer Software Restricted Rights clause at 52.227-19 and the limitations set forth in Electronics for Imaging, Inc.’s standard commercial

agreement for this software. Unpublished rights reserved under the copyright laws of the United States.

Printed in the United States of America on recycled paper.

Part Number:

n/a

CE Mark

The CE marking applied to this product symbolises Rank Xerox’s declaration of conformity with the following applicable directives of the European Union as of

the dates indicated.

January 1, 1996—Council Directive 70/80/CCO amended by Council Directive 93/68/EEO. Approximation of the laws of the member states related to low

voltage equipment.

January 1, 1996—Council Directive 59/336/EEC. Approximation of the laws of the member states related to electromagnetic compatibility.

A full declaration deﬁning the relevant directives and referenced standards can be obtained from your Rank Xerox representative.

WARNING: In order to allow this equipment to operate in proximity to industrial, scientiﬁc, and Medical (ISM) equipment, the external radiation from

ISM equipment may have to be limited or special migration measures taken.

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to

take adequate measures.

FCC Information

WARNING: FCC Regulations state that any unauthorized changes or modiﬁcations to this equipment not expressly approved by the manufacturer could void

the user’s authority to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,

and uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference

at his own expense.

Industry Canada Class A Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard

entitled, “Digital Apparatus” ICES-003 from Industry Canada.

Avis de Conformation Classe A d l’Industrie Canada

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la Classe A prescrites dans la

norme sur le matériel brouilleur, “Appareils Numériques” NMB-003 édictée par l’Industrie Canada.

Certiﬁcate by Manufacturer/Importer

This is to certify that the FC07 is shielded against radio interference in accordance with the provisions of VFG 243/1991. The German Postal Services have been

advised that this device is being put on the market and that they have been given the right to inspect the series for compliance with the regulations.

Electronics for Imaging, Inc.

Bescheinigung des Herstellers/Importeurs

Heirmit wird bescheinigt, dass der FC07 im Uebereinstimmung mit den Bestimmungen der VFG 243/1991 Funk-Entstort ist. Der Deutschen Bundespost wurde

das Inverkehrbringen dieses Geraetes angezeigt und die Berechtigung zur Ueberpruefung der Serie auf Einhaltung der Bestimmungen eingeraumt.

Electronics for Imaging, Inc.

RFI Compliance Notice

This equipment has been tested concerning compliance with the relevant RFI protection requirements both individually and on system level (to simulate normal

operation conditions). However, it is possible that these RFI Requirements are not met under certain unfavorable conditions in other installations. It is the user

who is responsible for compliance of his particular installation.

Dieses Geraet wurde einzeln sowohl als auch in einer Anlage, die einen normalen Anwendungsfall nachbildet, auf die Einhaltung der Funk-entstoerbestimmungen

geprueft. Es ist jedoch moeglich, dass die Funk-enstoerbestimmungen unter unguenstigen Umstaenden bei anderen Geraetekombinationen nicht eingehalten

werden. Fuer die Einhaltung der Funk-entstoerbestimmungen seigner gesamten Anlage, in der dieses Geraet betrieben wird, ist der Betreiber verantwortlich.

Compliance with applicable regulations depends on the use of shielded cables. It is the user who is responsible for procuring the appropriate cables.

Einhaltung mit betreffenden Bestimmungen kommt darauf an, dass geschirmte Ausfuhrungen gebraucht werden. Fuer die beschaffung richtiger Ausfuhrungen

ist der Betreiber verantwortlich.

Software License Agreement

Before using the Software, please carefully read the following terms and conditions. BY USING THIS SOFTWARE, YOU SIGNIFY THAT YOU HAVE

ACCEPTED THE TERMS OF THIS AGREEMENT. If you cannot or do not accept these terms, you may return the entire package within ten (10) days to

the Distributor or Dealer from which you obtained them for a full refund.

Electronics for Imaging, Inc. grants to you a non-exclusive, non-transferable license to use the software and accompanying documentation (“Software”) included

with the Fiery X2 you have purchased, including without limitation the PostScript

®

software provided by Adobe Systems Incorporated.

You may:

a. use the Software solely for your own customary business purposes and solely with Fiery X2;

b. use the digitally-encoded machine-readable outline and bitmap programs (“Font Programs”) provided with Fiery X2 in a special encrypted format (“Coded

Font Programs”) to reproduce and display designs, styles, weights, and versions of letters, numerals, characters and symbols (“Typefaces”) solely for your own

customary business purposes on the display window of the Fiery X2 or monitor used with Fiery X2;

c. use the trademarks used by Electronics for Imaging to identify the Coded Font Programs and Typefaces reproduced therefrom (“Trademarks”); and

d. assign your rights under this Agreement to a transferee of all of your right, title and interest in and to Fiery X2 provided the transferee agrees to be bound by

all of the terms and conditions of this Agreement.

You may not:

a. make use of the Software, directly or indirectly, to print bitmap images with print resolutions of 600 dots per inch or greater, or to generate fonts or typefaces

for use other than with Fiery X2;

b. make or have made, or permit to be made, any copies of the Software, Coded Font Programs, accompanying documentation or portions thereof, except as

necessary for use with the Fiery X2 unit purchased by you; provided, however, that under no circumstances may you make or have made, or permit to be made,

any copies of that certain portion of the Software which has been included on the Fiery X2 hard disk drive. You may not copy the documentation;

c. attempt to alter, disassemble, decrypt or reverse engineer the Software, Coded Font Programs or accompanying documentation.

d. rent or lease the Software.

Proprietary Rights

You acknowledge that the Software, Coded Font Programs, Typefaces, Trademarks and accompanying documentation are proprietary to Electronics for Imaging

and its suppliers and that title and other intellectual property rights therein remain with Electronics for Imaging and its suppliers. Except as stated above, this

Agreement does not grant you any right to patents, copyrights, trade secrets, trademarks (whether registered or unregistered), or any other rights, franchises or

licenses in respect of the Software, Coded Font Programs, Typefaces, Trademarks or accompanying documentation. You may not adapt or use any trademark or

trade name which is likely to be similar to or confusing with that of Electronics for Imaging or any of its suppliers or take any other action which impairs or reduces

the trademark rights of Electronics for Imaging or its suppliers. The trademarks may only be used to identify printed output produced by the Coded Font

Programs. At the reasonable request of Electronics for Imaging, you must supply samples of any Typeface identiﬁed with a trademark.

Conﬁdentiality

You agree to hold the Software and Coded Font Programs in conﬁdence, disclosing the Software and Coded Font Programs only to authorized users having a need

to use the Software and Coded Font Programs as permitted by this Agreement and to take all reasonable precautions to prevent disclosure to other parties.

Remedies

Unauthorized use, copying or disclosure of the Software, Coded Font Programs, Typefaces, Trademarks or accompanying documentation will result in automatic

termination of this license and will make available to Electronics for Imaging other legal remedies.

Limited Warranty And Disclaimer

Electronics for Imaging warrants that, for a period of ninety (90) days from the date of delivery to you, the Software under normal use will perform without

signiﬁcant errors that make it unusable. Electronics for Imaging’s entire liability and your exclusive remedy under this warranty (which is subject to you returning

Fiery X2 to Electronics for Imaging or an authorized dealer) will be, at Electronics for Imaging’s option, to use reasonable commercial efforts to attempt to correct

or work around errors, to replace the Software with functionally equivalent software, or to refund the purchase price and terminate this Agreement. Some states

do not allow limitations on duration of implied warranty, so the above limitation may not apply to you.

Except for the above express limited warranty, Electronics for Imaging makes and you receive no warranties or conditions on the Products, express, implied, or

statutory, and Electronics for Imaging speciﬁcally disclaims any implied warranty or condition of merchantability or ﬁtness for a particular purpose.

For warranty service, please contact your authorized service/support center.

EXCEPT FOR THE ABOVE EXPRESS LIMITED WARRANTY, ELECTRONICS FOR IMAGING MAKES AND YOU RECEIVE NO WARRANTIES

OR CONDITIONS ON THE SOFTWARE OR CODED FONT PROGRAMS, EXPRESS, IMPLIED, STATUTORY, OR IN ANY OTHER PROVISION

OF THIS AGREEMENT OR COMMUNICATION WITH YOU, AND ELECTRONICS FOR IMAGING SPECIFICALLY DISCLAIMS ANY IMPLIED

WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Electronics for Imaging does not warrant that

the operation of the software will be uninterrupted or error free or that the Software will meet your speciﬁc requirements.

Limitation Of Liability

IN NO EVENT WILL ELECTRONICS FOR IMAGING OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOST

PROFITS, COST OF COVER OR OTHER SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING FROM THE USE OF

THE SOFTWARE, CODED FONT PROGRAMS OR ACCOMPANYING DOCUMENTATION, HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY. THIS LIMITATION WILL APPLY EVEN IF ELECTRONICS FOR IMAGING OR ANY AUTHORIZED DEALER HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE. YOU ACKNOWLEDGE THAT THE PRICE OF THE UNIT REFLECTS THIS ALLOCATION OF RISK.

BECAUSE SOME STATES/JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR

INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

Export Controls

You agree that you will not export or re-export the Software or Coded Font Programs in any form without the appropriate United States and foreign government

licenses. Your failure to comply with this provision is a material breach of this Agreement.

Government Use

Use, duplication or disclosure of the Software by the United States Government is subject to restrictions as set forth in subdivision (c) (1) (ii) of the Rights in

Technical Data and Computer Software clause at DFARS 252.227-7013 or in subparagraphs (c) (1) and (2) of the Commercial Computer Software—Restricted

Right Clause at 48 CFR 52.227-19, as applicable.

Third Party Beneﬁciary

You are hereby notiﬁed that Adobe Systems Incorporated, a California corporation located at 345 Park Avenue, San Jose, CA 95110-2704 (“Adobe”) is a third-

party beneﬁciary to this Agreement to the extent that this Agreement contains provisions which relate to your use of the Fonts, the Coded Font Programs, the

Typefaces and the Trademarks licensed hereby. Such provisions are made expressly for the beneﬁt of Adobe and are enforceable by Adobe in addition to Electronics

for Imaging.

General

This Agreement will be governed by the laws of the State of California.

This Agreement is the entire agreement held between us and supersedes any other communications or advertising with respect to the Software, Coded Font

Programs and accompanying documentation.

If any provision of this Agreement is held invalid, the remainder of this Agreement shall continue in full force and effect.

If you have any questions concerning this Agreement, please write to Electronics for Imaging, Inc., Attn: Licensing Dept. or see Electronics for Imaging’s web site

at www.eﬁ.com.

Electronics for Imaging, Inc.

2855 Campus Drive

San Mateo, CA 94403

Contents

Introduction

About the documentation

xi

Speciﬁcations

xii

User software

xiii

System requirements

xiv

Windows xiv

Mac OS xv

UNIX (TCP/IP) xvi

Parallel port xvi

IPX (Novell) xvii

Installing User Software on a Windows Computer

Installing Windows software

1

Downloading printer ﬁles with the Installer WebTool 2

Setting up the Fiery X2 as a PostScript printer

2

Setting up PostScript printing with Windows 95 3

Setting up PostScript printing with Windows 3.1x 17

Setting up PostScript printing with Windows NT 4.0 21

Installing Fiery X2 software

33

Fiery Downloader and Fiery Print Calibrator 33

Fiery Spooler 35

Fiery Scan 36

Using the software for the ﬁrst time

37

Conﬁguring the connection to the server 37

Conﬁguring the connection for Fiery Spooler 40

Copying color ﬁles from the User Software CD

42

Installing the Fiery X2 ICM printer proﬁle for Windows 95 44

Installing ﬁles for Adobe Photoshop 44

x Table of Contents

Installing User Software on a Mac OS Computer

Installing Mac OS software

49

Downloading printer ﬁles with the Installer WebTool 50

Setting up PostScript printing with Mac OS

50

Setting up the Fiery X2 in the Chooser 51

Installing Fiery X2 software and fonts

53

Screen fonts 56

Copying color ﬁles from the User Software CD

57

Installing ﬁles for Adobe Photoshop 58

Downloading Installers with Fiery WebTools

Setting up Fiery WebTools

63

Using the Installer WebTool

64

Troubleshooting

On a Windows computer

67

Setting up IPX (Novell) printing for Windows NT Workstation 67

Installing the Adobe PostScript Printer Driver 67

Problems with the Fiery utilities on Windows 95 or Windows NT 67

On a Mac OS computer

68

Setting up the Fiery X2 in the Chooser 68

Installing screen fonts 68

Index

xi About the documentation

This manual describes how to install the user software for the Fiery X2 Color Server

™

and set up printing from Windows and Mac OS computers. For information about

setting up network servers and clients to use the Fiery X2 Color Server, see the

Administrator Guide

. For general information on using the color copier, your

computer, your application software, or your network, see the manuals that accompany

those products.

N

OTE

:

The term “Fiery X2” is used to refer to the Fiery X2 Color Server.

The Fiery X2 supports Empress (5750), Regal (5790), and Countess (5799) digital

copier printers.

Your Fiery X2 includes a media pack containing the following:

• User Software CD

• System Software CD

• User Documentation CD

• Kodak Gray Scale package

• Printed Release Notes (described below)

• Quick Start Notes

About the documentation

This manual is part of the set of Fiery X2 documentation, which includes the following

manuals for users and system administrators:

• The

Administrator Guide

explains basic conﬁguration and administration of the

Fiery X2 for the supported platforms and network environments. It also includes

guidelines for setting up UNIX, Windows NT, and Novell

NetWare servers to

provide Adobe

PostScript printing services to clients.

•

Getting Started

describes how to install software to enable users to print to the

Fiery X2. Speciﬁcally, it describes installation of PostScript printer drivers, printer

description ﬁles, and other software provided on the User Software CD. It also

explains how to connect each user to the network.

Introduction

xii Introduction

• The

User Guide

describes the printing features of the Fiery X2 for users who send

jobs via remote workstations on the network or via a direct parallel port connection.

It also explains how to use the Fiery WebTools and Fiery X2 client utilities to

manage jobs and maintain color quality, and provides troubleshooting information

for problems that may arise.

•

Release Notes

provide last-minute product information and workarounds for some of

the problems you may encounter.

Speciﬁcations

The Fiery X2 has the following features:

• MIPS R5000, 200 MHz CPU

• 160MB RAM

• Internal 2GB hard disk drive

• External CD-ROM drive (available as an optional kit)

• SCSI port

• Supports AppleTalk, TCP/IP, and IPX protocols simultaneously

• Supports parallel port communication

• Supports thinnet (thin coaxial Ethernet cable or 10Base2), thicknet (thick coaxial

Ethernet cable or 10Base5), and unshielded twisted pair (Fast Ethernet 100BaseTX

or Ethernet 10BaseT)

• Supports Token Ring networking (available as an optional kit)

• Supports Adobe PostScript 3

• Includes 136 fonts (117 Adobe Type 1 PostScript and 19 TrueType)

In addition, two Adobe Multiple Master fonts are included and are used for font

substitution in PDF ﬁles.

• Built-in ColorWise

™

color management and NetWise

™

networking features

• Fiery WebTools

™

• Fiery Downloader

™

, Fiery Print Calibrator

™

, and Fiery Spooler

™

client utilities

• Fiery Scan

™

plug-in

xiii User software

User software

The full set of Fiery X2 user software is provided on the User Software CD. Installers

for the printer ﬁles can also be downloaded with the Installer WebTool.

Adobe PostScript Printer

Driver

Enables you to print to the Fiery X2 from Windows

3.1x, Windows 95, and Mac OS computers;

supports special Fiery X2 and PostScript 3 features.

PostScript Printer Description

ﬁles (PPDs)

Files for use with the PostScript printer driver; they

allow the Fiery X2 to appear in popular applications’

Print and Page Setup dialog boxes. The Fiery X2

PPDs provide information about the Fiery X2 and

your particular copier model to the application and

printer driver you are using.

PostScript Screen Fonts Screen fonts for the 136 PostScript printer fonts

installed on the Fiery X2 (117 Adobe Type 1 and 19

TrueType). See Appendix B of the

User Guide

for a

complete list.

Fiery Downloader Enables you to print PostScript ﬁles, Encapsulated

PostScript (EPS) ﬁles, and Portable Document

Format (PDF) ﬁles directly to the Fiery X2 without

opening the application in which they were created.

Fiery Downloader also enables you to manage the

printer fonts installed on the Fiery X2.

Fiery Print Calibrator Enables you to calibrate the Fiery X2 remotely from

your computer. Proper calibration keeps color

consistent across time.

Fiery Spooler Enables you to view the order and priority of print

jobs, customize printer settings for jobs, delete jobs,

and move jobs between queues. You can also use it

to view job accounting information.

Fiery Scan plug-in A TWAIN plug-in module for Photoshop that

enables you to scan images from the copier directly

into Photoshop.

xiv Introduction

System requirements

To install the Fiery X2 user software on a Windows or Mac OS computer, the

computer must be equipped with a built-in or external CD-ROM drive.

Windows

To print to the Fiery X2, you need:

• A Windows-based computer with an 80486, AMD, or Pentium processor

• Windows 95, Windows 3.1x, or Windows NT 4.0

• At least 4MB of RAM

To use Fiery utilities (Fiery Downloader, Fiery Print Calibrator, and Fiery Spooler) you

also need:

•

Either

Windows 95

or

Windows NT 4.0 with NT Service Pack 3

• At least 16MB of RAM

To use Fiery Scan, you also need Adobe Photoshop version 2.5 or later.

To use Fiery WebTools, you also need:

•

Either

Netscape Communicator v4.0.4 with Java enabled

or

Microsoft Internet

Explorer v3.0.2 with Java enabled

N

OTE

:

Netscape and Microsoft continue to release frequent updates to their browsers.

As support cannot be guaranteed for all versions, use the versions speciﬁed above for

best results.

Color management ﬁles ColorSync and ICM color management ﬁles that

enable you to maintain consistent color from your

original artwork to the colors displayed on your

monitor to the printed output.

Color reference ﬁles Reference pages that you can print to view the range

of colors available on your Fiery X2. For the most

predictable color results, refer to these pages when

deﬁning colors in applications.

xv System requirements

• A monitor that supports 16-bit color at a minimum resolution of 800

x

600

• A TCP/IP enabled network and the IP address or DNS name of the Fiery X2

• Web Services enabled on the Fiery X2

N

OTE

:

Fiery utilities and Fiery WebTools are not supported with Windows 3.1x.

With Microsoft Windows 95, you also need:

• IPX/SPX or TCP/IP networking protocol installed

N

OTE

:

You must have TCP/IP networking protocol installed in order to use Fiery

Spooler; Fiery Spooler is not supported over IPX/SPX.

• Adobe PostScript Printer Driver for Windows version 4.2 or later (version 4.2.2 is

included with the user software)

With Microsoft Windows 3.1x, you also need:

• IPX networking protocol installed

• IPX/SPX networking software for IPX/SPX communication

• MS-DOS version 5.0 or later

• Adobe PostScript Printer Driver for Windows version 3.0 or later (version 3.0.1 is

included with the user software)

With Microsoft Windows NT 4.0 you also need:

• TCP/IP or AppleTalk networking protocol installed

• The Windows PostScript Printer Driver that came with your Windows NT 4.0

system software; however, some Fiery X2 printing features may not be available. For

details, see the

User Guide

.

Mac OS

To print to the Fiery X2, you need:

• A Mac OS-based computer

• At least 8MB of RAM

• EtherTalk installed

xvi Introduction

• Apple System software version 7.5 or later

• Adobe PostScript Printer Driver version 8.5 or later (version 8.5.1 is included with

the user software)

To use the Fiery utilities (Fiery Downloader, Fiery Print Calibrator, and Fiery Spooler),

you also need:

• A Power Macintosh computer

• At least 16MB of RAM

To use Fiery Scan, you also need Adobe Photoshop version 2.5 or later.

To use Fiery WebTools, you also need:

• Netscape Communicator v4.0.4 with Java enabled

N

OTE

:

Netscape continues to release frequent updates to its browser. As support cannot

be guaranteed for all versions, use the version speciﬁed above for best results.

• A TCP/IP enabled network and the IP address or DNS name of the Fiery X2

• Web Services enabled on the Fiery X2

UNIX (TCP/IP)

To print to the Fiery X2 with a UNIX workstation, you need:

• A workstation with standard TCP/IP connectivity (for example, Sun SPARCstation

or Silicon Graphics workstation with Solaris version 2.x or SunOS version 4.1.x

software)

• TCP/IP printing software that conforms to RFC1179 (Berkeley lpd protocol)

Parallel port

To print to the Fiery X2 using the parallel port, you need:

• A Windows-based computer with an 80486, AMD, or Pentium processor

• At least 4MB of RAM

xvii System requirements

• The parallel cable included with the Fiery X2

The cable has a DB-25 male connector (that connects to the computer) on one end

and a DB-25 female connector (that connects to the Fiery X2) on the other.

IPX (Novell)

To use the Fiery X2 with an IPX (Novell) network, you need:

• A Novell server

• Novell NetWare software version 4.x or 3.x

• Support for Ethernet SNAP, Ethernet II, Ethernet 802.3, Ethernet 802.2,

Token Ring SNAP, or Token Ring

1 Installing Windows software

This chapter describes installing software and setting up printing from a

Windows-based computer running Windows 95, Windows 3.1x, or Windows NT 4.0.

The general steps for installing the Fiery X2 software are:

• Install the Adobe PostScript printer driver (Windows 95 and Windows 3.1x) or

Windows PostScript printer driver (Windows NT 4.0) and PostScript Printer

Description ﬁles (PPDs) (for all Windows systems).

• Set up the printer driver to communicate with the Fiery X2.

• Install the Fiery utilities (Fiery Downloader, Fiery Print Calibrator, and

Fiery Spooler) and Fiery Scan plug-in (Windows 95 and Windows NT 4.0 only).

• Conﬁgure the connection for Fiery Downloader, Fiery Print Calibrator, and Fiery

Scan.

• Conﬁgure the connection for Fiery Spooler.

• Copy additional color reference and application ﬁles from the User Software CD as

needed.

Installing Windows software

The Instalrs folder on the User Software CD contains the following installer folders:

• Calib—Fiery Print Calibrator installer

• Download—Fiery Downloader installer

• PS_drvr—Adobe PostScript printer driver installers for Windows 95 and

Windows 3.1x, and Fiery X2 PPD ﬁles for all supported Windows systems

• Scan—TWAIN module installer, which enables you to use the Fiery Scan plug-in

for Adobe Photoshop

• Spooler—Fiery Spooler installer

Installing

User Software

on a Windows

Computer

2 Installing User Software on a Windows Computer

In addition, the User Software CD includes various color ﬁles. These ﬁles must be

copied or installed from the CD and placed in the appropriate locations on your hard

disk (see “Copying color ﬁles from the User Software CD” on page 42):

• ICM printer proﬁle

• Separation Tables and a monitor settings ﬁle for use with Adobe Photoshop

• PostScript CMYK reference ﬁle

• PostScript PANTONE Coated Color Reference ﬁle

• RGB color reference ﬁles for specifying colors from Microsoft Word and PowerPoint

Downloading printer ﬁles with the Installer WebTool

Installers for the Fiery X2 printer ﬁles can be downloaded from the Fiery X2 with the

Installer WebTool (if the site administrator has enabled Internet access to the

Fiery X2). For instructions, see “Using the Installer WebTool” on page 64.

Once you download the installers, the installation process is identical to installing from

the User Software CD.

Setting up the Fiery X2 as a PostScript printer

To set up the Fiery X2 as a PostScript printer, you need a PostScript printer driver and

the appropriate Fiery X2 PPD ﬁle.

• For Windows 95 or Windows 3.1x, install the appropriate Adobe PostScript printer

driver, included with the Fiery X2 user software. Both drivers are capable of

providing access to all Fiery X2 features; in addition, the Adobe PostScript printer

driver for Windows 95 supports PostScript 3.

• For Windows NT 4.0 systems, install the printer driver that came with your

Windows system software. This driver may not support all Fiery X2 features.

The following procedures are speciﬁc to each version of Windows.

Page is loading ...

Xerox Regal 5790 Installation guide

This manual is also suitable for

Xerox Regal 5790 Installation guide

Related papers

Other documents