Renkforce Main board Suitable Owner's manual

Renkforce
Brand
Renkforce
Model
Main board Suitable
Type
Owner's manual
How to PCB mainboard of
RF100?
•1.Turn off the power of Printer.
•2.侧放机器，松开下封板的四个地脚螺丝，拆下下封板；
1- X axis power port
2- Y axis power port
3- Z axis power port
4- Extruder power port
5- Heating rod port
6- N/A
7- Fan power port
8- Motherboard power port
9- USB port
10- N/A
11- N/A
12- Thermistors port
13- Display PCB port01
14- Display PCB port02
15- X+: N/A
16- X-: Limit switch of X axis port
17- Y+: Limit switch of Y axis port
18- Y-: N/A
19- Z+: N/A
20- Z-: Limit switch of Z axis port
•3. RF100 Mainboard port Introduction
•4.Remove the cables of NO.:1(X axis power port)/NO.2(Y axis power port
)/NO.3(Z axis power port)/NO.4 ports(Extruder power port)
Attention:
01-In order to prevent confusion or calbe mass, please use stickers to
mark the cables one by one.
02- Record the cables by NO.1/NO.2/NO.3/NO.4
•5.Remove the cables of NO.5(Heating rod port)/NO.7(Fan power
port)/NO.8 port(Motherboard power port).
01-In order to prevent confusion or calbe mass, please use stickers to
mark the cables one by one.
02- Record the cables by NO5/NO.7/NO.8
•6.Remove the cable of NO.12 port(Thermistors port ).
01-In order to prevent confusion or calbe mass, please use stickers to
mark the cables one by one.
02- Record the cables by NO.12
•7.Remove the cable of NO.13(Display PCB port01)/NO.14port(Display
PCB port02).
01-In order to prevent confusion or calbe mass, please use stickers to
mark the cables one by one.
02- Record the cables by NO.13/NO.14
•8.Remove the cable of NO.16(Limit switch of X axis port)/NO.17(Limit
switch of Y axis port)/NO.20 port(Limit switch of Z axis port).
01-In order to prevent confusion or calbe mass, please use stickers to
mark the cables one by one.
02- Record the cables by NO.16/NO.17/NO.20
•9.Lossen the mainboard PCB screws and replace the new mainboard by
Allen Key 2.5mm
•10.Install the cable of NO.1(X axis power port)/NO.2(Y axis power port
)/NO.3(Z axis power port)/NO.4 ports(Extruder power port)
•11.Install the cable of NO.5(Heating rod port)/NO.7(Fan power port)/NO.8
port(Motherboard power port).
•12.Install the cable of NO.12 port(Thermistors port )
•13.Install the cable of NO.16(Limit switch of X axis port)/NO.17(Limit
switch of Y axis port)/NO.20 port(Limit switch of Z axis port).
•14.Install the cable of NO.13(Display PCB port01)/NO.14port(Display PCB
port02).
•16.Reinstall bottom cover and then tighten 4 bottom screws by Allen
3.0mm.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Renkforce Main board Suitable Owner's manual

Renkforce
Brand
Renkforce
Model
Main board Suitable
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents