Danfoss VLT® AutomationDrive FC 360 Installation guide

Brand: Danfoss

Model: VLT® AutomationDrive FC 360

Type: Installation guide

This manual is also suitable for

VLT AutomationDrive FC 360

Safety

WARNING

HIGH VOLTAGE!

Frequency converters contain high voltage when

connected to AC mains input power. Installation, start up,

and maintenance should be performed by qualified

personnel only. Failure to perform installation, start up, and

maintenance by qualified personnel could result in death

or serious injury.

High Voltage

Frequency converters are connected to hazardous mains

voltages. Extreme care should be taken to protect against

shock. Only trained personnel familiar with electronic

equipment should install, start, or maintain this equipment.

WARNING

UNINTENDED START!

When the frequency converter is connected to AC mains,

the motor may start at any time. The frequency converter,

motor, and any driven equipment must be in operational

readiness. Failure to be in operational readiness when the

frequency converter is connected to AC mains could result

in death, serious injury, equipment, or property damage.

Unintended Start

When the frequency converter is connected to the AC

mains, the motor may be started by means of an external

switch, a serial bus command, an input reference signal, or

a cleared fault condition. Use appropriate cautions to

guard against an unintended start.

WARNING

DISCHARGE TIME!

Frequency converters contain DC-link capacitors that can

remain charged even when the frequency converter is not

powered. To avoid electrical hazards, disconnect AC mains,

any permanent magnet type motors, and any remote DC-

link power supplies, including battery backups, UPS and

DC-link connections to other frequency converters. Wait for

the capacitors to fully discharge before performing any

service or repair work. The amount of wait time is listed in

the Discharge Time table. Failure to wait the specified time

after power has been removed before doing service or

repair could result in death or serious injury.

Voltage [V] Minimum waiting time [minutes]

4 15

380-480 0.37-7.5 kW 11-75 kW

High voltage may be present even when the warning LEDs are

off!

Discharge Time

Symbols

The following symbols are used in this manual.

WARNING

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. It may

also be used to alert against unsafe practices.

CAUTION

Indicates a situation that may result in equipment or

property-damage-only accidents.

NOTE

Indicates highlighted information that should be regarded

with attention to avoid mistakes or operate equipment at

less than optimal performance.

Approval

Safety

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark

Safety

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark

Contents

1 Quick Start

1.1 Identification and Variants

1.2 Hand On/Auto On Mode

1.3 Application Selections

1.4 Jumper Terminal 12 and 27

1.5 Automatic Motor Adaptation (AMA)

2 Introduction

2.1 Exploded Views

2.2 Product Overview

2.3 Additional Resources

2.4 Frame Sizes and Power Ratings

3 Installation

3.1 Mechanical Installation

3.2 Electrical Installation

3.2.1 General Requirements 13

3.2.2 Earth (Grounding) Requirements 13

3.2.2.1 Leakage Current (>3.5 mA) 13

3.2.3 Mains, Motor and Earth Connections 14

3.2.4 Control Wiring 14

3.2.4.1 Access 14

3.2.4.2 Control Terminal Types 15

3.2.4.3 Control Terminal Functions 15

3.2.4.4 Using Screened Control Cables 16

3.3 Serial Communication

4 User Interface and Programming

4.1 Programming

4.1.1 Programming with the Numerical Local Control Panel (LCP 21) 18

4.1.2 LCP 21 18

4.1.3 The Right-Key Function 19

4.2 Quick Menu

4.3 Main Menu

4.4 Parameter List

4.4.1 Main Menu Structure 23

5 Wiring Examples

6 Warnings and Alarms

6.1 System Monitoring

Contents

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 1

6.2 Warning and Alarm Types

6.2.1 Warnings 30

6.2.2 Alarm Trip vs. Alarm Trip Lock 30

6.3 Warning and Alarm Displays

6.4 Warning and Alarm Definitions

7 Basic Troubleshooting and FAQs

7.1 Start Up and Operation

8 Specifications

8.1 Power-dependent Specifications

8.1.1 Mains Supply 3 x 380-480 V AC 35

8.2 General Technical Data

8.3 Fuse Specifications

8.3.2 Recommendations 41

8.3.3 CE Compliance 41

8.4 Connection Tightening Torques

Index

Contents

VLT

AutomationDrive FC 360 Quick Guide

2 MG06A202 - VLT

is a registered Danfoss trademark

1 Quick Start

WARNING

Improper use could result in death, serious injury,

equipment, or property damage. Before installing or using

the equipment, carefully read 1 Safety and 3 Installation!

1.1 Identification and Variants

Confirm that the equipment matches the requirements

and ordering information by checking power size, voltage

and overload data on the name plate of the frequency

converter.

130BC435.11

CHASSIS/IP20

VLT

MADE BY DANFOSS

IN CHINA

AutomationDrive

www.danfoss.com

T/C: FC-360HK37T4E20H2BXCDXXSXXXXAXBX

P/N: 134F2970 S/N: 691950A240

0.37 kW 0.5HP High Overload

IN: 3x380-480V 50/60Hz 1.24/0.99A

OUT: 3x0-Vin 0-500Hz 1.2/1.1A(Tamb. 45 C)

CAUTION:

SEE MANUAL

WARNING:

AND LAODSHARING BEFORE SERVICE

STORED CHARGE DO NOT TOUCH UNTIL 4 MIN. AFTER

DISCONNECTION

RISK OF ELECTRIC SHOCK-DUAL SUPPLY DISCONNECT MAINS

Illustration 1.1 Name Plate 1 and 2

1 Typecode

2 Ordering number

3 Specifications

Table 1.1 Legend to Illustration 1.1

1-6: Product Name

7: Overload

H: Heavy Duty

Q: Normal Duty

8-10: Power Size

0.37-75 kW e.g.

K37: 0.37 kW

1K1: 1.1 kW

11K: 11 kW etc.

11-12: Voltage Class T4: 380-480 V three phases

13-15: IP Class E20: IP20

16-17: RFI H2: C3 Class

18: Brake chopper

X: No

B: Built-in

19: LCP X: No

20: PCB Coating C: 3C3

21: Mains terminals D: Load sharing

29-30: Embedded Fieldbus

AX: No

A0: Profibus

AL: Profinet

Table 1.2 Type Code: Selection of Different Features and Options

See for options and accessories.

1) Only 11-75 kW for normal duty variants. Fieldbus unavailable for

normal duty.

2) For all power sizes see 2.4 Frame Sizes and Power Ratings

3) Not available yet.

4) 0.37-22 kW with built-in brake chopper. 30-75 kW external brake

chopper only.

130BC437.10

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

F C - 3 6 0 H T 4 E 2 0 H 2 X X C D X X S X X X X A X B X

Q B 0

Illustration 1.2 Typecode String

Quick Start

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 3

1 1

1.2 Hand On/Auto On Mode

After installation (see 3 Installation), there are two simple

ways to start up the frequency converter, Hand On and

Auto On mode. At the first power-up it is in auto on mode.

130BD062.10

Hand

Reset

Auto

Warn

Alarm

Illustration 1.3 Location of Hand On, Off/Reset and Auto On keys

on the NLCP

•

Press [Hand On] to provide a local start command

to the frequency converter. Press [

▲

] and [

▼

] to

increase and decrease speed.

•

Press [Off/Reset] to stop the frequency converter.

•

Press [Auto On] to control the frequency

converter either via control terminals or serial

communication.

CAUTION

Since the frequency converter is in auto on mode at first

power up, the frequency converter may start the motor

directly.

NOTE

5-12 Terminal 27 Digital Input has coast inverse as default

setting. Connect terminals 12 and 27 to test Hand On/Auto

On running.

For LCP operation, see 4 User Interface and Programming.

1.3

Application Selections

Use the selections for quick application set-up of the most

common applications by setting 0-16 Application Selections.

When necessary, the selections can be modified for

individual needs. All selections are for Auto On mode.

NOTE

When an application is selected, relevant parameters are

automatically set. Customer specific configuration of all

parameters based on specific requirements is still possible.

CAUTION

If any of the applications below are selected, relay 1 will

be set to [Running] and relay 2 will be set to [Alarm]

Application

Pumps, fans, compressors

130BC430.10

+24V 12

DI1 18

DI2 19

DI3 27

DI4 29

DI5 32

DI6 33

DI7 31

COM 20

+10V 50

AI1 53

AI2 54

COM 55

AO1 45

AO2 42

FC 360

Start

Coast inverse

Jog

4-20

Description

For applications where a

value (e.g. pressure,

temperature) must be

kept at a desired level by

sensor feedback

Parameter settings

1-00 (Configuration Mode): [3] Process Close Loop

1-03 (Torque Characteristics): [1] Variable Torque

3-00 (Ref Range): [0] Min- Max

3-15 (Ref Source 1): [0] No Function

4-12 (Motor Low Limit): 30.0 Hz

4-14 (Motor High Limit): 50.0 Hz

5-10 (DI 18 Selection): [8] Start

5-12 (DI 27 Selection): [2] Coast Inverse

5-14 (DI 32 Selection): [14] Jog

5-40 (Relay 1 Selection): Running

5-40 (Relay 2 Selection): Alarm

6-22 (AI 54 Low): 4.0 mA

6-23 (AI 54 High): 20.0 mA

6-29 (AI 54 Mode): [0] Current Mode

6-70 (Term 45 Mode): [0] 0-20 mA

6-71 (AO45): [100] Output freq

6-90 (Term 42 Mode): [0] 0-20 mA

6-91 (AO42): [103] Motor current

7-20 (Process CL feedback source): [2] Analog input 54

Table 1.3 [1] Process Closed Loop

Quick Start

VLT

AutomationDrive FC 360 Quick Guide

4 MG06A202 - VLT

is a registered Danfoss trademark

Application

Local/Remote

130BC431.10

+24V 12

DI1 18

DI2 19

DI3 27

DI4 29

DI5 32

DI6 33

DI7 31

COM 20

+10V 50

AI1

AI2

COM 55

AO1

AO2 42

FC 360

Start

Coast inverse

Setup select

4-20

Description

For applications

where the speed

reference can be

switched between

local potentiometer

and remote current

signal

Parameter settings Setup 1 Setup 2

0-10 (Active Set-

up)

[9] Multi Set-up [9] Multi Set-up

0-12 (Link Set-up) [20] Linked [20] Linked

1-00 (Configuration

Mode)

[0] Speed Open Loop [0] Speed Open Loop

3-00 (Ref Range) [0] Min- Max [0] Min- Max

3-15 (Ref Source 1) [1] AI 53 [2] AI 54

3-16 (Ref Source 2)

4-12 (Motor Low

Limit)

25.0 Hz 25.0 Hz

4-14 (Motor High

Limit)

50.0 Hz 50.0 Hz

5-10 (DI 18

Selection)

[8] Start [8] Start

5-12 (DI 27

Selection)

[2] Coast Inverse [2] Coast Inverse

5-14 (DI 32

Selection)

[23] Set-up select [23] Set-up select

5-40 (Relay 1

Selection)

Running Running

5-40 (Relay 2

Selection)

Alarm Alarm

6-10 (AI 53 Low) 0.07 V

6-11 (AI 53 High) 10 V

6-19 (AI 53 Mode) [1] Voltage Mode

6-22 (AI 54 Low) 4.0 mA

6-23 (AI 54 High) 20.0 mA

6-29 (AI 54 Mode) [0] Current Mode

6-70 (Term 45

Mode)

[0] 0-20 mA [0] 0-20 mA

6-71 (AO45) [100] Output freq [100] Output freq

6-90 (Term 42

Mode)

[0] 0-20 mA [0] 0-20 mA

6-91 (AO42) [103] Motor current [103] Motor current

Table 1.4 [2] Local/Remote

Application

Conveyors, extruders

130BC432.10

+24V 12

DI1 18

DI2 19

DI3 27

DI4 29

DI5 32

DI6 33

DI7 31

COM 20

+10V 50

AI1

AI2

COM 55

AO1

AO2 42

FC 360

Start

Coast inverse

Description

For running at a stable

speed by a voltage

reference signal.

Parameter settings

1-00 (Configuration Mode): [0] Speed Open Loop

3-00 (Ref Range): [0] Min- Max

3-15 (Ref Source 1): [1] AI 53

4-12 (Motor Low Limit): 25.0 Hz

4-14 (Motor High Limit): 50.0 Hz

5-10 (DI 18 Selection): [8] Start

5-12 (DI 27 Selection): [2] Coast Inverse

5-40 (Relay 1 Selection): Running

5-40 (Relay 2 Selection): Alarm

6-10 (AI 53 Low): 0.07 V

6-11 (AI 53 High): 10 V

6-19 (AI 53 Mode): [1] Voltage Mode

6-70 (Term 45 Mode): [0] 0-20 mA

6-71 (AO45): [100] Output freq

6-90 (Term 42 Mode): [0] 0-20 mA

6-91 (AO42): [103] Motor current

Table 1.5 [3] Speed Open Loop

Quick Start

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 5

1 1

Application

Machine tools, texturizers

130BC433.10

+24V 12

DI1 18

DI2 19

DI3 27

DI4 29

DI5 32

DI6 33

DI7 31

COM 20

+10V 50

AI1

AI2

COM 55

AO1

AO2 42

FC 360

Start

Coast inverse

Description

For precise speed

applications with 24 V

encoder feedback

Parameter settings

1-00 (Configuration Mode): [1] Speed Close Loop

3-00 (Ref Range): [0] Min- Max

3-15 (Ref Source 1): [1] AI 53

3-16 (Ref Source 2): [11] Local Bus Ref

4-12 (Motor Low Limit): 20.0 Hz

4-14 (Motor High Limit): 50.0 Hz

5-10 (DI 18 Selection): [8] Start

5-12 (DI 27Selection): [2] Coast Inverse

5-14 (DI 32 Selection): [82] Encoder input B

5-15 (DI 33 Selection): [81] Encoder input A

5-40 (Relay 1 Selection): Running

5-40 (Relay 2 Selection): Alarm

6-10 (AI 53 Low): 0.07 V

6-11 (AI 53 High): 10 V

6-19 (AI 53 Mode): [1] Voltage Mode

6-70 (Term 45 Mode): [0] 0-20 mA

6-71 (AO45): [100] Output freq

6-90 (Term 42 Mode): [0] 0-20 mA

6-91 (AO42): [103] Motor current

7-00 (Speed PID Feedback Source): [1] 24 V encoder

Table 1.6 [4] Speed Close Loop

Application

Industrial washing

machines, conveyors

130BC434.10

+24V 12

DI1 18

DI2 19

DI3 27

DI4 29

DI5 32

DI6 33

DI7 31

COM 20

+10V 50

AI1

AI2

COM 55

AO1

AO2 42

FC 360

Start

Coast inverse

Pre set ref bit 0

Pre set ref bit 1

Pre set ref bit 2

Description

For applications with

8 different speeds by

digital input. By using

another digital input,

16 speeds are

possible.

Parameter settings

1-00 (Configuration Mode): [0] Speed Open Loop

3-00 (Ref Range): [0] Min- Max

3-15 (Ref Source 1): [0] No Function

4-14 (Motor High Limit): 50.0 Hz

5-10 (DI 18 Selection): [8] Start

5-12 (DI 27 Selection): [2] Coast Inverse

5-13 (DI 29 Selection): [16] Preset ref bit 0

5-14 (DI 32 Selection): [17] Preset ref bit 1

5-15 (DI 23 Selection): [18] Preset ref bit 2

6-70 (Term 45 Mode): [0] 0-20 mA

6-71 (AO45): [100] Output freq

6-90 (Term 42 Mode): [0] 0-20 mA

6-91 (AO42): [103] Motor current

Table 1.7 [5] Multi-speed

NOTE

For further examples, refer to 5 Wiring Examples.

Quick Start

VLT

AutomationDrive FC 360 Quick Guide

6 MG06A202 - VLT

is a registered Danfoss trademark

1.4 Jumper Terminal 12 and 27

When using factory default programming values, jumper

wire may be required between terminal 12 and terminal 27

for the frequency converter to operate.

•

Digital input terminal 27 is designed to receive an

24 V DC external interlock command. In many

applications, the user wires an external interlock

device to terminal 27

•

When no interlock device is used, wire a jumper

between control terminal 12 to terminal 27. This

provides internal 24 V signal on terminal 27

•

No signal present prevents the unit from

operating

1.5 Automatic Motor Adaptation (AMA)

Automatic motor adaptation (AMA)

It is highly recommended to run AMA because it measures

the electrical characteristics of the motor to optimize

compatibility between the frequency converter and the

motor under VVC

plus

mode.

•

The frequency converter builds a mathematical

model of the motor for regulating output motor

current thus enhancing motor performance.

•

Some motors may be unable to run the complete

version of the test. In that case, select Enable

reduced AMA

•

If warnings or alarms occur, see 6 Warnings and

Alarms

•

Run this procedure on a cold motor for best

results

To run AMA using the numeric LCP (NLCP)

1. By default parameter setting, connect terminal 12

and 27 before running AMA.

2. Enter the main menu.

Go to parameter group 1-** Load and Motor.

4. Press [OK].

5. Set motor parameters using name plate data for

parameter group J1-1-2* Motor Data.

Set motor cable length in 1-42 Motor Cable Length

Go to 1-29 Automatic Motor Adaptation (AMA).

8. Press [OK].

Select [1] Enable complete AMA.

10. Press [OK].

11. The test will run automatically and indicate when

it is complete.

NOTE

AMA function in FC 360 does not cause the motor to run

and it does not harm the motor.

Quick Start

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 7

1 1

2 Introduction

2.1 Exploded Views

130BC439.10

Illustration 2.1 Exploded View J1-J5 (0.37-22 kW), IP20

NLCP (accessory) 10 2-Pole Relay 2 (0.37-7.5 kW)

3-Pole Relay 2 (11-22 kW)

2 Control cassette 11 Mains terminal

3 RFI switch (screw M3x12 only) 12 Cable strain relief (0.37-2.2 kW: accessory)

4 Removable fan assembly 13 RS-485 com pluggable terminal

5 Grounding clamp (accessory) 14 Fixed I/O terminals

6 Shielded cable grounding clamp and strain relief

(accessory)

15 Fixed I/O terminals

7 Motor terminal (U V W) and brake and load sharing

terminal

16 Terminal cover

8 PE ground 17 Option-B (MCB102/103 accessories)

9 3-Pole relay 1

Table 2.1 Legend to Illustration 2.1

Introduction

VLT

AutomationDrive FC 360 Quick Guide

8 MG06A202 - VLT

is a registered Danfoss trademark

2.2 Product Overview

A frequency converter is an electronic motor controller

that converts AC mains input into a variable AC waveform

output. The frequency and voltage of the output are

regulated to control the motor speed or torque. The

frequency converter can vary the speed of the motor in

response to system feedback, such as changing

temperature or pressure for controlling fan, compressor, or

pump motors. The frequency converter can also regulate

the motor by responding to remote commands from

external controllers.

In addition, the frequency converter monitors the system

and motor status, issues warnings or alarms for fault

conditions, starts and stops the motor, optimizes energy

efficiency, and offers many more control, monitoring, and

efficiency functions. Operation and monitoring functions

are available as status indications to an outside control

system or serial communication network.

2.3 Additional Resources

Other resources are available to understand advanced

frequency converter functions and programming.

•

The Programming Guide provides greater detail

on working with parameters.

•

The Design Guide is intended to provide detailed

capabilities and functionality to design motor

control systems.

•

Optional equipment is available that may change

some of the procedures described. Be sure to see

the instructions supplied with those options for

specific requirements.

Contact the local Danfoss supplier or go to

www.danfoss.com/Products/Literature/VLT+Technical

+Documentation.htm for downloads.

2.4 Frame Sizes and Power Ratings

Frame size

380-480 V

J1 J2 J3 J4 J5 J6 J7

Power size [kW] 0.37-2.2 3.0-5.5 7.5 11-15 18.5-22 30-45 55-75

Dimensions

[mm]

130BC449.10

Height A 210 272.5 272.5 317.5 410 520 550

Width B 75 90 115 133 150 233 308

Depth C

(with option B)

168 (181) 168 (181) 168 (181) 245 (258) 245 (258) 242 332

Mounting holes

a 198 260 260 297.5 390

b 60 70 90 105 120

Mounting screw M4 M5 M5 M6 M6

Table 2.2 Frames Sizes, Power Ratings and Dimensions

Introduction

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 9

3 Installation

3.1 Mechanical Installation

Select the best possible operation site by considering:

•

Ambient operating temperature

•

Installation method

•

How to cool the unit

•

Position of the frequency converter

•

Cable routing

•

Power source supplying correct voltage and

necessary current

•

Motor current rating within the maximum current

from the frequency converter

•

Correct rating of external fuses and circuit

breakers

Cooling and Mounting:

•

Top and bottom clearance for air cooling must be

provided, see Table 3.1 for clearance requirements

•

Derating for temperatures starting from 45 °C

and elevation 1000 m above sea level must be

considered. See the equipment Design Guide for

detailed information.

Enclosure

J1-J5 J6/J7

Clearance above and below the

unit [mm]

100 100-200

Table 3.1 Minimum Airflow Clearance Requirements

•

Mount the unit vertically

•

IP20 units (but NOT IP21 units) allow side-by-side

installation

•

Improper mounting can result in over heating

and reduced performance

•

Use the slotted mounting holes on the unit for

wall mounting, when provided

•

See 8.4 Connection Tightening Torques for proper

tightening specifications.

Installation

VLT

AutomationDrive FC 360 Quick Guide

10 MG06A202 - VLT

is a registered Danfoss trademark

3.2 Electrical Installation

This section contains detailed instructions for wiring the frequency converter.

130BC438.12

3 Phase

power

input

Switch Mode

Power Supply

Motor

Analog Output

Interface

(PNP) = Source

(NPN) = Sink

ON=Terminated

OFF=Open

Brake

resistor

91 (L1)

92 (L2)

93 (L3)

50 (+10 V OUT)

53 (A IN)

54 (A IN)

55 (COM A IN)

0/4-20 mA

12 (+24 V OUT)

31 (D IN)

18 (D IN)

20 (COM D IN)

10 V DC

15 mA 100 mA

+ - + -

(U) 96

(V) 97

(W) 98

(PE) 99

(A OUT) 45

(A OUT) 42

(P RS-485) 68

(N RS-485) 69

(COM RS-485) 61

S801

0/4-20 mA

RS-485

+10 V DC

0/4-20 mA

0-10 V DC

24 V DC

240 V AC, 2 A

24 V (NPN)

0 V (PNP)

24 V (NPN)

19 (D IN)

24 V (NPN)

0 V (PNP)

24 V

0 V

(D IN/OUT)

0 V (PNP)

24 V (NPN)

(D IN/OUT)

0 V

24 V

24 V (NPN)

0 V (PNP)

24 V (NPN)

33 (D IN)

32 (D IN)

P 5-00

(+UDC) 82

(BR) 81

24 V (NPN)

0 V (PNP)

0-10 V DC

(-UDC) 88

RFI

0 V

240 V AC, 2 A

Relay 1

Relay 2 2)

Illustration 3.1 Basic Wiring Schematic Drawing

A=Analog, D=Digital

1) Built-in brake chopper available from 0.37-22 kW

2) Relay 2 is 2-pole for J1-J3 and 3-pole for J4-J7. Relay 2 of J4-J7 with terminals 4, 5 and 6 same NO/NC logic as Relay 1.

3) Dual DC choke in 30-75 kW

4) Switch S801 (bus terminal) can be used to enable termination on the RS-485 port (terminals 68 and 69).

Installation

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 11

3 3

130BD391.11

Reset

Auto

Hand

Back

Status Quick

Main

Illustration 3.2 Typical Electrical Connection

PLC 6 Min. 200 mm (7.9 in) between control cables, motor and mains

2 Frequency converter 7 Motor, 3-phase and PE

3 Output contactor (Generally not recommended) 8 Mains, 3-phase and reinforced PE

4 Earth (grounding) rail (PE) 9 Control wiring

5 Cable insulation (stripped) 10

Equalising min. 16 mm

(0.025 in)

Table 3.2 Legend to Illustration 3.2

Installation

VLT

AutomationDrive FC 360 Quick Guide

12 MG06A202 - VLT

is a registered Danfoss trademark

3.2.1 General Requirements

WARNING

EQUIPMENT HAZARD!

Rotating shafts and electrical equipment can be hazardous.

Extreme care should be taken to protect against electrical

hazards when applying power to the unit. All electrical

work must conform to national and local electrical codes

and installation, start up, and maintenance should only be

performed by trained and qualified personnel. Failure to

follow these guidelines could result in death or serious

injury.

CAUTION

WIRING ISOLATION!

Run input power, motor wiring and control wiring in three

separate metallic conduits or use separated shielded cable

for high frequency noise isolation. Failure to isolate power,

motor and control wiring could result in less than

optimum frequency converter and associated equipment

performance.

Run motor cables from multiple frequency converters

separately. Induced voltage from output motor cables run

together can charge equipment capacitors even with the

equipment turned off and locked out.

•

An electronically activated function within the

frequency converter provides overload protection

for the motor. The overload provides Class 20

motor protection. See 6 Warnings and Alarms for

details on the trip function.

Wire Type and Ratings

•

All wiring must comply with local and national

regulations regarding cross-section and ambient

temperature requirements.

•

Danfoss recommends that all power connections

be made with a minimum 75 °C rated copper

wire.

•

See 8 Specifications for recommended wire sizes.

3.2.2

Earth (Grounding) Requirements

WARNING

GROUNDING HAZARD!

For operator safety, it is important to ground the

frequency converter properly by a certified electrical

installer in accordance with national and local electrical

codes as well as instructions contained within this

document. Ground currents are higher than 3.5 mA. Failure

to ground the frequency converter properly could result in

death or serious injury.

•

Proper protective grounding for equipment with

ground currents higher than 3.5 mA must be

established, see 3.2.2.1 Leakage Current (>3.5 mA)

•

A dedicated ground wire is required for input

power, motor power and control wiring

•

Use the clamps provided with the equipment for

proper ground connections

•

Do not ground one frequency converter to

another in a “daisy chain” fashion (see

Illustration 3.3)

•

Keep the ground wire connections as short as

possible

•

Using high-strand wire to reduce electrical noise

is recommended

•

Follow motor manufacturer wiring requirements

130BC500.10

FC 1

FC 2

FC 3

Illustration 3.3 Grounding Principle

3.2.2.1

Leakage Current (>3.5 mA)

Follow national and local codes regarding protective

earthing of equipment with a leakage current > 3.5 mA.

The earth leakage current depends on various system

configurations including RFI filtering, screened motor

cables, and frequency converter power.

EN/IEC61800-5-1 (Power Drive System Product Standard)

requires special care if the leakage current exceeds 3.5 mA.

Earth grounding must be reinforced in one of the

following ways:

Installation

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 13

3 3

•

Earth ground wire of at least 10 mm

(copper

wire)

•

Two separate earth ground wires both complying

with the dimensioning rules

See EN 60364-5-54 § 543.7 for further information.

Using RCDs

Where residual current devices (RCDs), also known as earth

leakage circuit breakers (ELCBs), are used, comply with the

following:

•

Use RCDs of type B only which are capable of

detecting AC and DC currents

•

Use RCDs with an inrush delay to prevent faults

due to transient earth currents

•

Dimension RCDs according to the system configu-

ration and environmental considerations

3.2.3

Mains, Motor and Earth Connections

WARNING

INDUCED VOLTAGE!

Run output motor cables from multiple frequency

converters separately. Induced voltage from output motor

cables run together can charge equipment capacitors even

with the equipment turned off and locked out. Failure to

run output motor cables separately could result in death

or serious injury.

Earthing (grounding) clamps are provided for motor wiring

(see Illustration 3.4).

•

Do not install power factor correction capacitors

between the frequency converter and the motor

•

Do not wire a starting or pole-changing device

between the frequency converter and the motor

•

Follow motor manufacturer wiring requirements

•

All frequency converters may be used with an

isolated input source as well as with ground

reference power lines. When supplied from an

isolated mains source (IT mains or floating delta)

or TT/TN-S mains with a grounded leg (grounded

delta), set 14-50 RFI Filter to OFF (size J6-J7) or

remove the RFI screw (J1-J5). When off, the

internal RFI filter capacitors between the chassis

and the intermediate circuit are isolated to avoid

damage to the intermediate circuit and to reduce

earth capacity currents in accordance with IEC

61800-3.

•

Do not install switch between the frequency

converter and the motor in IT mains.

130BC501.10

02 03

Illustration 3.4 Mains, Motor and Earth Connections

Illustration 3.4 represents mains input, motor, and earth

grounding for basic frequency converters. Actual configu-

rations vary with unit types and optional equipment.

3.2.4

Control Wiring

3.2.4.1 Access

•

Remove access cover plate with a screw driver.

See Illustration 3.5.

130BC504.10

Illustration 3.5 Control Wiring Access for J1-J7 Enclosures

Installation

VLT

AutomationDrive FC 360 Quick Guide

14 MG06A202 - VLT

is a registered Danfoss trademark

3.2.4.2 Control Terminal Types

Illustration 3.6 shows the frequency converter control

terminals. Terminal functions and default settings are

summarized in Table 3.3.

42 45

130BC505.12

Illustration 3.6 Control Terminal Locations

See 8.2 General Technical Data for terminal ratings details.

Termi

nal

Parame

ter

Default

setting Description

Digital I/O, Pulse I/O, Encoder

12 - +24 V DC

24 V DC supply voltage.

Maximum output current is

100 mA for all 24 V loads.

18 5-10 [8] Start

Digital inputs.

19 5-11 [10] Reversing

31 5-16 [0] No operation Digital input, pulse input.

32 5-14 [0] No operation

Digital input, 24 V encoder.

33 5-15 [0] No operation

5-12

5-30

DI [2] Coast

inverse

DO [0] No

operation

Selectable for either digital

input, digital output or

pulse output. Default

setting is digital input.

5-13

5-31

DI [14] Jog

DO [0] No

operation

20 -

Common for digital inputs

and 0 V potential for 24 V

supply.

Analog inputs/outputs

42 6-91 [0] No operation Programmable analog

output. The analog signal

is 0-20 mA or 4-20 mA at a

maximum of 500 Ω. Can

also be configured as

digital outputs

45 6-71 [0] No operation

Termi

nal

Parame

ter

Default

setting Description

50 - +10 V DC

10 V DC analog supply

voltage. 15 mA maximum

commonly used for

potentiometer or

thermistor.

53 6-1* Reference

Analog input. Selectable

for voltage or current.54 6-2* Feedback

55 - Common for analog input

Serial communication

61 -

Integrated RC-Filter for

cable screen. ONLY for

connecting the screen

when experiencing EMC

problems.

68 (+) 8-3*

RS-485 Interface. A control

card switch is provided for

termination resistance.

69 (-) 8-3*

Relays

01, 02,

5-40 [0] [0] No operation

Form C relay output. These

relays are in various

locations depending upon

the frequency converter

configuration and size.

Usable for AC or DC

voltage and resistive or

inductive loads.

RO2 in J1-J3 enclosure is 2-

pole, only terminals 04 and

05 are available

04, 05,

5-40 [1] [0] No operation

Table 3.3 Terminal Descriptions

3.2.4.3

Control Terminal Functions

Frequency converter functions are commanded by

receiving control input signals.

•

Each terminal must be programmed for the

function it will be supporting in the parameters

associated with that terminal. See Table 3.3 for

terminals and associated parameters.

•

It is important to confirm that the control

terminal is programmed for the correct function.

See 4 User Interface and Programming for details

on accessing parameters and for details on

programming.

•

The default terminal programming is intended to

initiate frequency converter functioning in a

typical operational mode.

Installation

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 15

3 3

3.2.4.4 Using Screened Control Cables

Correct screening

The preferred method in most cases is to secure control

and serial communication cables with screening clamps

provided at both ends to ensure best possible high

frequency cable contact.

If the earth potential between the frequency converter and

the PLC is different, electric noise may occur that will

disturb the entire system. Solve this problem by fitting an

equalizing cable as close as possible to the control cable.

Minimum cable cross section: 16 mm

PLC

130BB922.12

PE PE

<10 mm

Illustration 3.7 Screening Clamps at Both Ends

Min. 16 mm

2 Equalizing cable

Table 3.4 Legend to Illustration 3.7

50/60 Hz ground loops

With very long control cables, ground loops may occur. To

eliminate ground loops, connect one end of the screen-to-

ground with a 100 nF capacitor (keeping leads short).

100nF

PLC

<10 mm

130BB609.12

Illustration 3.8 Connection with a 100 nF Capacitor

Avoid EMC noise on serial communication

This terminal is connected to earth via an internal RC link.

Use twisted-pair cables to reduce interference between

conductors. The recommended method is in Illustration 3.9:

130BB923.12

PE PE

<10 mm

Illustration 3.9 Twisted-pair Cables

Min. 16 mm

2 Equalizing cable

Table 3.5 Legend to Illustration 3.9

Alternatively, the connection to terminal 61 can be

omitted:

130BB924.12

PE PE

<10 mm

Illustration 3.10 Twisted-pair Cables without Terminal 61

Min. 16 mm

2 Equalizing cable

Table 3.6 Legend to Illustration 3.10

3.3 Serial Communication

Connect RS-485 serial communication wiring to terminals

(+)68 and (-)69.

•

Screened serial communication cable is

recommended

•

See 3.2.2 Earth (Grounding) Requirements for

proper grounding

130BB489.10

RS-485

Illustration 3.11 Serial Communication Wiring Diagram

Installation

VLT

AutomationDrive FC 360 Quick Guide

16 MG06A202 - VLT

is a registered Danfoss trademark

For basic serial communication set-up, select the following:

Protocol type in 8-30 Protocol.

Frequency converter address in 8-31 Address.

Baud rate in 8-32 Baud Rate.

•

Two communication protocols are internal to the

frequency converter. Follow motor manufacturer

wiring requirements.

Danfoss FC

Modbus RTU

•

Functions can be programmed remotely using

the protocol software and RS-485 connection or

in parameter group 8-** Communications and

Options

•

Selecting a specific communication protocol

changes various default parameter settings to

match that protocol’s specifications along with

making additional protocol-specific parameters

available

Installation

VLT

AutomationDrive FC 360 Quick Guide

MG06A202 - VLT

is a registered Danfoss trademark 17

3 3

4 User Interface and Programming

4.1 Programming

4.1.1 Programming with the Numerical

Local Control Panel (LCP 21)

The FC 360 supports graphic and numerical local control

panels as well as blind covers. This chapter covers

programming with LCP 21. For programming with the

GLCP, see the VLT

AutomationDrive FC 360 Programming

Guide.

NOTE

The frequency converter can also be programmed from a

PC via RS-485 com-port by installing the MCT-10 Setup

software. This software can either be ordered using code

number 130B1000 or downloaded from the Danfoss Web

site: www.danfoss.com/BusinessAreas/DrivesSolutions/

softwaredownload

4.1.2 LCP 21

The LCP 21 is divided into four functional sections.

A. Numeric display

B. Menu key

C. Navigation keys and indicator lights (LEDs)

D. Operation keys and indicator lights (LEDs)

130BC506.10

Setup 1

13 14 15

Status

Quick

Main

Hand

O

Reset

Auto

Back

Warn

Alarm

Illustration 4.1 View of the LCP 21

A. Numeric Display

The LCD-display is back-lit with 1 numeric line. All data is

displayed in the LCP.

1 Set-up number shows the active set-up and the edit set-

up. If the same set-up acts as both active and edit set-up,

only that set-up number is shown (factory setting). When

active and edit set-up differ, both numbers are shown in

the display (Setup 12). The number flashing, indicates the

edit set-up.

2 Parameter number.

3 Parameter value.

4 Motor direction is shown to the bottom left of the display

– indicated by a small arrow pointing either clockwise or

counterclockwise.

5 The triangle indicates if the LCP is in status, quick menu or

main menu.

Table 4.1 Legend to Illustration 4.1

130BD135.10

Setup 12

INDEX

AHP

VkW

srpm

Hz%

n2n1

p5 p4

p3 p2 p1

Illustration 4.2 Display Information

B. Menu Key

Press [Menu] to select between status, quick menu or main

menu.

C. Navigation keys and indicator lights (LEDs)

Green LED/On: Control section is working.

7 Yellow LED/Warn.: Indicates a warning.

8 Flashing Red LED/Alarm: Indicates an alarm.

9 [Back]: For moving to the previous step or layer in the

navigation structure

Arrows [

▲

] [

▼

]: For maneuvering between parameter groups,

parameters and within parameters or increasing/decreasing

parameter values. Can also be used for setting local

reference.

11 [OK]: For selecting a parameter and for accepting changes to

parameter settings

[►]: For moving from left to right within the parameter value

in order to change each digit individually. See description in

4.1.3 The Right-Key Function.

Table 4.2 Legend to Illustration 4.1

User Interface and Programm...

VLT

AutomationDrive FC 360 Quick Guide

18 MG06A202 - VLT

is a registered Danfoss trademark

Page is loading ...

Danfoss VLT® AutomationDrive FC 360 Installation guide

Brand: Danfoss

Model: VLT® AutomationDrive FC 360

Type: Installation guide

This manual is also suitable for

VLT AutomationDrive FC 360

Download PDF

report

Danfoss VLT® AutomationDrive FC 360 Installation guide

This manual is also suitable for

Danfoss VLT® AutomationDrive FC 360 Installation guide

Related papers

Other documents