AP-120-MNT-WJ Access Point Enclosure
Installation Guide
0510583-03 | July 2010 1
Introduction
The AP-120-MNT-WJ access point (AP) enclosure allows you to install an AP-121 or AP-125 access point
on the wall, directly over an installed junction box. Additionally, this enclosure can be mounted to the
ceiling, using ceiling tile rails.
The AP-120-MNT-WJ kit includes the following pieces:
z Plastic base to attach over a standard installed junction box or ceiling tile rail
z Plastic enclosure cover
z The following plastic connector plate styles:
1x Keystone connector plate
1x Siemon connector plate
1x Blank plate
z Blank fillers for unused connectors
2x Keystone
2x Siemon
z 1x M4 x 25mm T-20 Torx screw
z 1x T-20 Torx key
z 1x white paper label sheet
z 2x clear window to cover labels
z 9/16" rail adapter
Additional Tools
z A screwdriver that matches the screws in the cover plate over the installed junction box
z (Optional) flat-head screwdriver or similar tool to punch out antenna access cutouts
APenc_011
Top Cover Base
M4x25mm
Torx Screw
T-20 Torx Key
9/16” Rail
Adapter
Clear
Windows
Siemon Connector
Plate
Siemon 45*
Blanking Plates
Keystone
Blanking Plates
Keystone
Connector
Plate
Blank Plate
Parts not to scale
2 AP-120-MNT-WJ Access Point Enclosure | Installation Guide
Installing the AP Enclosure
To install the AP enclosure:
1. Attach the base plate as follows:
a. Remove the cover plate from an installed junction box (Figure 1). Save the screws.
Figure 1 Removing the installed cover plate
b. Snap the cable connectors out of the removed cover plate and set the cover plate aside. Identify the
Ethernet cable that will be connected to the AP-121 or AP-125. The Ethernet cable must have a male
RJ-45 connector.
c. Attach the enclosure base plate to the junction box using the screws from the removed cover plate
(Figure 2).
d. Skip step 2 and proceed to step 3.
Figure 2 Attaching the base plate
NOTE
For ceiling mounted APs, skip step 1 and proceed to step 2
APenc_002
APenc_003
AP-120-MNT-WJ Access Point Enclosure | Installation Guide 3
2. To install the AP enclosure on a ceiling rail:
a. Pull the necessary cables through a prepared hole in the ceiling tile near where the AP will be placed.
The prepared hole must line up with the cable pass-through in the base plate.
b. (Optional) if the ceiling rail is 9/16", install the ceiling rail adapter (Figure 3).
c. Hold the enclosure base next to the ceiling rail with the ceiling rail at approximately a 30-degree
angle to the ceiling tile rail (Figure 3).
d. Rotate the enclosure base clockwise until the device clicks into place on the ceiling rail.
Figure 3 Installing the AP on a ceiling rail
3. Connect the Ethernet cable to Ethernet port 0 on the AP. Hold the unused cables down and to the right
of the screw post as you continue with the next step.
4. Attach the AP to the mounted base plate as follows:
a. Position the antennas on the AP along the sides of the unit.
b. Locate the mounting posts on the base plate and the mounting holes on the AP (Figure 4).
Figure 4 Preparing to attach the AP
APenc_008
Ceiling tile
Ceiling tile rail
Align tabs
with rail
Installing
9/16” Rail Adapter
Rotate AP
until it clicks
into place
APenc_004
Mounting Posts
Mounting Holes
4 AP-120-MNT-WJ Access Point Enclosure | Installation Guide
c. Align the AP mounting holes over the posts on the base plate.
d. Push the AP against the pegs and downward, until the pegs engage the slots at the top of the
mounting holes. (Figure 5)
Figure 5 Aligning and securing the AP on the base plate
APenc_005
AP-120-MNT-WJ Access Point Enclosure | Installation Guide 5
5. Attach the connector plate and connectors to the base plate as follows:
a. Select the connector plate that matches the existing connectors that were attached to junction box
face plate.
b. Attach the selected connector plate by sliding it over the opening in the bottom of the base. (See
Figure 6).
c. Once the connector plate is secure, attach the connectors to the openings in the plate. Any empty
opening should be filled using one of the connector plate blanks. (See Figure 6)
Figure 6 Attaching connector plate and connectors (AP not shown)
6. Position the AP’s antennas so they suit your deployment scenario. If you plan on keeping the antennas
hidden in the enclosure, skip this step and proceed to step 8.
NOTE
Once the connectors and connector plate blanks are in place, reposition the cables so they are routed below the
screw post, as shown in Figure 8 and Figure 9.
APenc_006
6 AP-120-MNT-WJ Access Point Enclosure | Installation Guide
7. Before installing the cover, if the antennas are to be extended, clear the antenna access cutouts (see
Figure 7).
a. For wall mounted APs, clear the access cutouts marked A. Note that there is a third access cutout
located on the base (not illustrated). It is located next to the connector plate
.
b. For ceiling mounted APs, clear the access cutouts marked B.
c. Extend the antennas as necessary.
Figure 7 Antenna openings
APenc_001
Access
cutout
areas
A
B
AP-120-MNT-WJ Access Point Enclosure | Installation Guide 7
8. Install the cover the cover as shown (see Figure 8).
a. Attach cover to base.
b. Use the M4 x 25mm T-20 Torx screw and the T-20 Torx key to secure the cover to the base.
c. (Optional) place paper labels and clear windows over the LED and screw openings.
Figure 8 Cover installation
APenc_007
8 July 2010 | 0510583-03
© 2010 Aruba Networks, Inc. All rights reserved.
The following graphics show the completed installation.
Figure 9 Wall mount with antennas extended
Figure 10 Ceiling mount with antennas extended
APenc_009
APenc_010
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Aruba Networks W-AP124/125 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Equip Fixing aid User manual
-
Dell W-AP114/115 User guide
-
Dell W-AP224/225 User guide
-
Dell PowerConnect W-IAP224/225 Installation guide
-
Aruba AP-105-MNT-C2 Installation guide
-
Aruba AP-130 Installation guide
-
-
-
-