K40 K40-200 Owner's manual

Brand
K40
Model
K40-200
Category
Radar detectors
Type
Owner's manual

This manual is also suitable for

3
Wake-Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Receiving Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
Radar Alert Sequence . . . . . . . . . . . . . . . . . . . . . . . . . .5
Laser Alert Sequence . . . . . . . . . . . . . . . . . . . . . . . . . .5
Laser Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Manual Laser Defuser Shut Down . . . . . . . . . . . . . . . . .6
Alerts from Non-Police Signals . . . . . . . . . . . . . . . . . . .7
K-Band Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Traffic Sensor Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
MultaRadar (MRCD/CT) Photo Radar . . . . . . . . . . . . . . .7
Auto Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Special Features/Functions . . . . . . . . . . . . . . . . . . . . . . . . .8-15
LED Dim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Highway|City|Filter/|Auto . . . . . . . . . . . . . . . . . . . . . . . .8
K-Band Narrow|Wide|Extended . . . . . . . . . . . . . . . . . .9
Ka-Band Narrow|Wide . . . . . . . . . . . . . . . . . . . . . . . . .9
Ka-Band Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Quiet Ride . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Mute Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Mark to Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Mark to Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Speed Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13
Customizable Settings . . . . . . . . . . . . . . . . . . . . . .13-15
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17
Add-On Options/Expert Remote Control . . . . . . . . . . . . . . .18
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Warranty/Guarantees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Table of Contents
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 1
5
Your K40 system will be ready for use following this automatic Wake-
Up sequence:
1. Start your vehicle – Your K40 system is designed to turn on
automatically every time your vehicle is started.
2. Wake-Up Sequence – Both front and rear alert LED’s in your
dash will flash (Platinum200 systems have one alert LED). The
voice will announce, “K40 Scan, Active”, you will then hear alerts
for X, K, Ka-Band, and laser.
Wake-Up Options can be changed in the Menu, page 14.
•Wake-Up Long: default and as described above.
•Wake-Up Short: LED’s will flash and you will hear an
abbreviated audible sequence of three beeps.
•Wake-Up Silent: an LED only sequence (no audible).
3. GPS Connection – After locating available satellites, the K40
system will announce, “GPS Connected”.
NOTE: If you don’t hear and/or see the Wake-Up sequence, press and
release the power button on the K40 remote control.
NOTE: If you are in a location that prevents connection with GPS
satellites (e.g. parking garage), your K40 system will still protect you
from all radar and laser threats (laser protection only available with
optional Laser Defuser installed). Once you drive to an unobstructed
location, the GPS will connect and you will hear, “GPS Connected”.
4
Your K40 system provides a combination of audio and visual alerts
to warn you when radar signals are detected.
Radar Alert Sequence
Your K40 system detects all North American police radar signals (X,
K, and Ka-Band). When a signal is identified:
• The K40 Platinum360 will announce the direction of the signal’s
source, either front or rear, along with the police radar band de-
tected. K40 Platinum200 systems will only announce the band
detected (this assumes the factory default “Voice On” setting
has not been changed).
• Signal strength and proximity to the radar source will be identified
as a series of Geiger counter-like tones. The faster the tone, the
closer you are to the source. Each police radar band alert has its
own distinctive tone.
Laser Alert Sequence
(only for K40 systems that include Laser Defusers
®
)
When your K40 system detects a laser signal:
• A voice announces, “Laser” (this assumes the factory default
“Voice On” setting has not been changed).
• You will then hear a distinct and urgent audio tone.
• LED(s) will pulse rapidly for the duration of the alert.
Wake-Up Sequence
(using factory default settings)
Receiving Alerts
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 2
6 7
Alerts from Non-Police Signals
Your K40 system is sensitive enough to detect signals generated by
non-police sources such as automatic doors, traffic flow sensors, and
radar based safety features. To learn how to minimize non-police
alerts, please read about TRAFFIC SENSOR FILTER (below), FILTER
options (page 8), QUIET RIDE (page 10), and MARK TO MUTE
(page 11).
K-Band Filter
Your K40 system rejects alerts from most vehicles on the road
equipped with radar-based safety features, such as collision avoid-
ance. Police radar reception and detection range are unaffected by
this feature.
Traffic Sensor Filter
(factory default off)
Your K40 system can reject alerts from traffic flow sensors usually
encountered during highway driving (limited use areas). This feature
can be enabled through the Menu (page 14).
MultaRadar (MRCD/CT) Photo Radar
(factory default off)
Your K40 system is capable of alerting to MRCD/CT photo radar
devices (limited use areas). This feature can be enabled through the
Menu (page 15). **LATE 2020 RELEASE**
Auto Volume
(factory default on)
Your K40 system will automatically reduce volume every three sec-
onds until it reaches the “Low” setting. This feature can be disabled
through the Menu (page 14).
Laser Settings
The optional Laser Defuser can be configured to one of three opera-
tional settings:
•Gives you more time to decelerate.
•Higher potential for jamming all the
way to the laser gun location.
•Gives you time to reduce speed. Officer
will then be able to obtain speed to
eliminate the suspicion of “jamming”
where use of jammers is restricted.
•For notification only. Officer will immedi-
ately obtain a speed reading on your
vehicle in this setting.
Description Recommended Use
For as long as the Laser Defuser is re-
ceiving a police laser gun signal, it will
continuously transmit back to the gun.
This is the factory default setting.
Alert Tone: standard laser alert tone.
Upon receiving a police laser signal,
the Laser Defuser will transmit a jam-
ming signal for up to five seconds,
then switches to
Receive Only mode
for 30 seconds.
Alert Tones: standard laser alert tone
for five seconds. Drops to a lower pitch
laser alert tone when in
Receive Only
mode.
The Laser Defuser will only detect po-
lice laser. No jamming signal will be
emitted.
Alert Tone: lower pitch laser alert tone.
•Tone notifies you while a jamming sig-
nal is being transmitted and when
Laser Defuser changes to
Receive
Only
.
Constant
Transmit
Pulse
Transmit
Receive
Only
Manual Laser Defuser Shut Down
During a Police Laser Encounter
Press and release button to automatically switch the Laser
Defuser(s) to Receive Only for 30 seconds during a laser encounter.
This gives you the option to control the duration of jamming sig-
nal being transmitted by the Laser Defusers.
MUTE
Defuser
Settings
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 4
8 9
K-Band Narrow|Wide|Extended
Select the range of police radar frequencies your K40 system scans.
This feature can be customized through the Menu (page 14).
• K Narrow scans the primary frequencies of police radar guns being
used.
- Scans 24.080-24.200GHZ
• K Wide scans a little above and below the standard range of frequen-
cies police radar guns can use. This is the factory default setting.
- Scans 24.026-24.285GHZ
• K Extended scans radar frequencies further below the standard
range of speed enforcement technology that may be used in your
area now or in the future.
- Scans 23.950-24.285GHZ
Ka-Band Narrow|Wide
Select the range of police radar frequencies your K40 system scans.
This feature can be customized through the Menu (page 14).
• Ka Narrow scans the primary frequencies of police radar guns
being used.
- Scans 33.7-33.9GHZ and 34.6-34.8GHZ and 35.4-35.6GHZ
• Ka Wide scans the entire possible range of frequencies police radar
guns can use. This is the factory default setting.
- Scans 33.4-36.00GHZ
Ka-Band Filter
Enables filtration of Ka-Band non-police radar signals, e.g. other
radar detectors and satellite broadcast bands (factory default off).
Use in high-traffic areas. Does not affect police radar detection
range. This feature can be enabled through the Menu (page 14).
LED DIM
• Press and release button on remote control to adjust LED
brightness to accommodate various driving environments. The set-
ting will save automatically.
Five LED Brightness Options:
1. “Day” - Brightest LED setting.
2. “Dusk” - Medium LED setting (factory default).
3. “Night” - Dimmest LED setting.
4. “Auto” - LED(s) adjust automatically from three seconds in “Day”, three
seconds in “Dusk”, and the duration of the alert in “Night”.
5. “Off” - LED(s) will not illuminate, you will still receive full audio alerts.
NOTE: “Off” reverts to “Night” upon K40 system Wake-Up.
Highway|City|Filter|Auto
•
Press and release button on remote control to change
the setting at any time. Your K40 system offers four levels of radar
sensitivity to accommodate various driving situations.
Special Features/Functions
DIM
CITY
HWY
For highway travel or in any area in
which you are unfamiliar with the types
of radar used.
When traveling in an urban area with
minimal non-police radar signals.
When traveling in a congested traffic
area with a high concentration of non-
police radar signals.
Settings Sensitivity Recommended Use
Maximum range and sensitivity on all
North American police radar signals
(X, K, and Ka-Band).
Decreases range and sensitivity on X,
K, and Ka-Bands.
X-Band off. Further range and sensitiv-
ity reduction of K and Ka-Band.
1. Highway
(factory
default)
2. City
3. Filter
4. Auto
Adjusts range and sensitivity on radar
bands based on vehicle speed.
0-45 mph-
Filter setting sensitivity.
46-55 mph-
City setting sensitivity.
56 mph+-
Highway setting sensitivity.
Less sensitivity in low speed situations
and more range and sensitivity in
higher speed situations.
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 6
10 11
Quiet Ride
The Quiet Ride function will automatically silence all radar and laser
alerts when traveling under a speed selection of your choice be-
tween 5-75 mph in 5 mph increments, or 10-120 kph in 10 kph
increments.
Visual alerts are unaffected by Quiet Ride settings.
The factory default setting for Quiet Ride is “20 mph”.
Activating/Adjusting Quiet Ride
• Press and release button on remote control to activate
the Quiet Ride menu. Voice will announce the current setting, e.g.
“Quiet Ride 20”, or the current speed setting.
• Press and release or buttons to adjust the speed
settings on Quiet Ride. Any selected speed setting indicates Quiet
Ride is on.
• When you have made your desired Quiet Ride speed selection, stop
scrolling and voice will announce, “Quiet Ride Set”.
NOTE: Locations that you have “Marked to Alert” (page 12) are
unaffected by Quiet Ride settings.
Mute Functions
Your K40 system provides two options to mute audio alerts (both
voice and tones):
• Press and release button to mute audio for 30 seconds or
the duration of the alert. Voice will announce, “Mute On”.
• Press and hold button for three seconds to mute audio for
5 minutes. Voice will announce “Extended Mute On”. Press and
hold MUTE button for three seconds to turn Extended Mute off.
• To turn the voice and tone alerts off, press and release button
until voice announces, “Volume Off”. You will continue to receive
visual alerts.
MUTE
MUTE
-
Mark to Mute
The Mark to Mute function allows you to mute any stationary radar
band/laser alert from a non-police source (e.g. an automatic door) in a
specific GPS location.
Using Mark to Mute
• Press and release button to mute a specific radar band/laser
alert. A signal must be present in order to mark a location for mute.
• A voice announces that a specific radar band/laser alert has been
muted (e.g. “K Muted”).
• You will no longer receive audible alerts for the muted radar band/laser
alert when within a 1,500 ft. radius of the muted location.
• You can string multiple muted locations together to extend the
1,500 ft. radius.
• You will still receive visual alerts from the alert LED(s).
• All other radar bands/laser alerts remain unaffected.
To remove a previously muted radar band/laser alert from
your database:
• Press and release button while in the marked location.
• Voice announces that a specific radar band/laser alert has been
removed (e.g. “K Muted Removed”).
To remove ALL stored muted radar bands/laser alerts:
• Press and hold button for ten seconds at any time.
• Voice announces, “All Muted Locations Cleared”.
MM
MM
QUIET
RIDE
+
-
MM
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 8
12 13
Mark to Alert
The Mark to Alert function saves specific GPS locations to create a
personal database of areas where increased awareness is desired, such
as school zones, speed traps, or red light cameras.
• Press and release button when you want to mark a location
for alert.
• Voice announces, “Marked to Alert”.
In the future you will be alerted as follows:
When you arrive… You will hear…
...within a radius of 1500 feet of a ...“Approaching Marked Location”
marked location and the alert LED(s) will flash twice
...at a marked location ...a single “Bing” tone and the alert
LED(s) will flash once
MA
To remove a previously marked location from your database:
• Press and release button while in the marked location.
• Voice announces, “Marked Location Removed”.
To remove all alert locations:
• Press and hold button for 10 seconds at any time.
• Voice announces, “All Alert Locations Cleared”.
MA
MA
Speed Monitor
Speed Monitor alerts you when a preselected speed is exceeded.
Speed Monitor can be set to any speed between 40-100 mph in 5
mph increments or 60-160 kph in 10 kph increments. The factory
default setting for Speed Monitor is “Off”.
Activating/Adjusting Speed Monitor
• Press and hold button for three seconds until the voice
announces, “Speed Monitor”.
• Press and release or button to adjust the Speed Monitor
speed setting. When you have chosen your desired Speed Monitor
setting, stop scrolling and the voice will announce, “Speed Moni-
tor Set”.
When driving and the Speed Monitor speed is exceeded:
• The K40 system will emit a continuous “Bing Bong” tone and the
alert LED(s) will flash.
• The alerts will continue until the vehicle’s speed is reduced to
below the Speed Monitor speed setting.
+
-
Customizable Settings
To change the factory preset features and customize your K40
system for the way you drive, follow the instructions below or
call a K40 Consultant at 800.323.5608.
To change settings:
• Press and release button to enter the MENU.
The voice will announce “Menu”, and then announce the first
customizable option and its current status.
• Press and release button to scroll through the options
until you reach the feature you want to change.
• Press and release or button to change an existing
setting. Voice will announce change.
To save your settings and exit:
• Press and hold button for three seconds, or wait 10
seconds and the system will automatically save your preferences.
• The voice will announce “Exit”.
MENU
MENU
+
-
MENU
CITY
HWY
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 10
1 Voice Type “Female Voice” “Female Voice” Choose male or female voice for
audio alerts.
2 Audible Voice ”Voice On“ “Voice On” For all initial audio alerts: “Voice
On” uses voice; “Voice Off”
uses tones only.
3 Wake-Up “Wake-Up Long”“Wake-Up Long”
•
“Wake-Up Long” is standard 5
Sequence second sequence.
•
“Wake-Up Short” uses an abbre-
viated sequence.
•
“Wake-Up Silent” lights only,
no audible.
4 Auto Volume “Auto Volume “Auto Volume Automatically reduces volume
On” On” every 3 seconds.
5 K -Band “K Wide” “K Wide”
•
K Wide scans the standard
Selectivity range of K-Band frequencies
that police radar guns can use.
•
K Narrow scans the primary K-
Band frequencies of police radar
guns being used.
•
K Extended scans radar frequen-
cies above and below the standard
range of speed enforcement tech
nology that may be used in your
area now or in the future.
6 Ka-Band “Ka Wide” “Ka Wide”
•
Ka Wide scans the entire possible
Selectivity range of Ka-Band frequencies
that police radar guns can use.
•
Ka Narrow scans the primary Ka-
Band frequencies of police radar
guns being used.
7 Ka Band Filter “Ka Filter “Ka Filter Enables filtration of Ka-Band
Off” Off” non-police radar signals.
8 Traffic Sensor “Traffic Sensor “Traffic Sensor Enables filtration of K-Band
Filter
Filter Off” Filter Off” radar signals from traffic flow
sensors.
Factory Default Setting
(voice confirmations)
Menu Options
(in sequential order)
Description
Platinum 200
System
Platinum 360
System
Customizable Settings
9 MRCD/CT MRCD Off MRCD Off Enables MRCD/CT photo radar
detection.
10 MRCD/CT Filter MRCD Filter Off MRCD Filter Off Reduces false alerts when
MRCD/CT detection is enabled.
11 Front Radar “Radar On” “Front Radar On” Allows user to turn off front radar
receiver.
12 Front X-Band “X-Band On” “Front X-Band Enables the detection of X-Band
On” radar from front receiver.
13 Front K-Band “K-Band On” “Front K-Band Enables the detection of K-Band
On” radar from front receiver.
14 Front Ka-Band “Ka-Band On” “Front Ka-Band Enables the detection of Ka-
On” Band radar from front receiver.
15 Rear Radar N/A “Rear Radar On” Allows user to turn off rear
radar receiver.
16 Rear X-Band N/A “Rear X-Band Enables the detection of X-Band
On” radar from rear receiver.
17 Rear K-Band N/A “Rear K-Band Enables the detection of K-Band
On” radar from rear receiver.
18 Rear Ka-Band N/A “Rear Ka-Band Enables the detection of Ka-
On” Band radar from rear receiver.
19 Optional Laser ”Laser On” ”Laser On” Enables the Laser Defuser. “Off”
Defuser disables the Laser Defuser.
20 Laser Settings “Laser Constant “Laser Constant Enables Laser Defuser for Con-
Transmit” Transmit” stant Transmit, Pulse Transmit,
or Receive Only.
21 mph/kph “mph” “mph” Choose miles per hour or
kilometers per hour.
22 Factory Reset “Factory Reset” “Factory Reset” Returns the system to its origi-
nal factory default settings.
23 Exit “Exit” “Exit”
•
Automatically exit menu after
10 seconds if no button is
pressed.
•
Press and hold button
for three seconds.
•
Press the button when “exit”
is announced.
Factory Default Setting
(voice confirmations)
Menu Options
(in sequential order)
Description
Platinum 200
System
Platinum 360
System
MENU
+
14 15
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 12
16
Press to mute audio
alerts for 30 seconds
or the duration of the
alert. Press and hold for
3 seconds to engage
Extended Mute (page
10). Press to automati-
cally put Laser Defuser
in Receive Only mode
duing a police laser
alert (page 6).
MARK TO ALERT
Press to “alert” specific
points of interest
(page 12).
Press to select level of
radar detector sensitivity
(page 8).
Press and hold for three
seconds to enter Speed
Monitor menu (page 12).
UP
Press to increase volume.
Use to scroll/change
menu options (pages
13-15).
DOWN
Press to decrease vol-
ume. Use to scroll and
change menu options
(pages 13-15).
POWER
Press to turn the K40
Platinum360|200
system on or off.
Adjust LED brightness
(page 8).
Press to confirm speed setting
and enter Quiet Ride menu
(page 10).
MARK TO MUTE
Press to “mute” a specific
radar band/laser alert in
a location (page 11).
Press to enter customizable
menu settings
(pages 13-15).
To Change Remote Battery:
Unlock and remove battery
door by turning the cover
counterclockwise as shown.
Insert battery with + symbol
side facing the + symbol side
of the battery door cover.
Requires use of a CR2032
cell battery.
To Use Supplied Visor Clip:
Insert the supplied clip into the
back of the remote control as
shown. Press firmly until it clicks.
OPEN
Remote Control
DIM
MM
MA
QUIET
RIDE
MENU
+
MUTE
-
17
CITY
HWY
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 14
18
Need some help? Call us at 800.323.5608 for assistance and to
customize your settings.
Troubleshooting Guide
Press and release power button on
remote control.
Replace battery in remote control with
CR2032 battery.
Check Mark to Mute settings (page 11).
Problem Possible Cause Solution
K40 system doesn’t turn on
and go through Wake-Up
sequence after starting car.
K40 system doesn’t respond to
remote control.
Alert lights flash but no alert
sound is heard.
K40 system has excessive
single “Bing” alerts.
Check Quiet Ride setting (page 10).
K40 system has excessive
“Bing Bong” alerts.
Erratic or frequent radar
alerts.
K40 system turned off.
Battery is dead in remote
control.
Vehicle in Mark to Mute loca-
tion.
Vehicle speed is below Quiet
Ride setting.
K40 system volume off.
Vehicle is in area of numerous
marked points of interest.
Vehicle speed is above Speed
Monitor setting.
High concentration of non-
police radar sources.
Check K40 system volume settings
(page 16).
Check Mark to Alert setting (page 12).
Check Speed Monitor setting (page 12).
Check Traffic Sensor Filter (page 7),
MRCD (page 7), Filter Mode (page 8),
Quiet Ride (page 10), and Mark to
Mute (page 11) settings.
19
Add-On Option
MUTE
Press to mute audio
alerts for 30 seconds
or the duration of the
alert. Press and hold
for 3 seconds to en-
gage Extended Mute
(page 10). Press to
automatically put Laser
Defuser in Receive
Only mode duing a
police laser alert
(page 6).
MARK TO ALERT
Press to “alert” specific points
of interest (page 12).
SENSITIVITY
Press to select level of
radar detector sensitivity
(page 8).
Press and hold for three
seconds to enter Speed
Monitor menu (pages
12-13).
UP
Press to increase volume.
Use to scroll/change
menu options (pages
13-15).
DOWN
Press to decrease volume.
Use to scroll and change
menu options (pages
13-15).
POWER
Press to turn the K40
Platinum360|200
system on or off.
DIM
Adjust LED brightness
(page 8).
QUIET RIDE
Press to confirm speed
setting and enter Quiet
Ride menu (page 10).
MARK TO MUTE
Press to “mute” a specific
radar band/laser alert in a
location (page 11).
MENU
Press to enter customiz-
able menu settings
(pages 13-15).
Expert Remote Controller
System control at your fingertips with a professionally installed, back-
lit control, designed to look like it was factory installed. Contact
your dealer for details.
(sold separately)
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 16
Product subject to one or more of the following patents:
U.S. Patents 7,298,248 B2
5,001,777
RE39,038
RE40,653
RE41,905
Other patents pending
Learn more at K40.com ©K40 Electronics
FCC IDS: W75-M2K-Y25 W75-RL-RCU II
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
In addition, any changes or modifications to this
product, which are not expressly approved by K40
Electronics in writing, could void the user’s authority
to operate this product.
Register your K40 system today
to activate your guarantees:
One-year warranty
The K40 Platinum360|200 is covered by a one year “repair or
replace” limited warranty. This coverage begins on date of pur-
chase and applies to manufacturing defects in product, materials
and workmanship only. Installation, removal, or re-installation is
not covered.
Guaranteed immunity from speeding tickets
If you get a radar speeding ticket within one year of purchase,
we’ll reimburse you for the full cost of the ticket.*
Guaranteed performance
If your K40 system does not outperform any other radar detector
you’ve owned, return it within 30 days for a full product credit.
Guaranteed from theft
If your K40 Platinum360|200 is ever stolen, we’ll replace the
stolen product.**
*Offer not valid for speeding ticket violations incurred in school or
construction zones, or connected with a DUI or DWI.
**Requires proof of purchase and a police report.
Register your K40 system online today by visiting
https://www.k40.com/radar-detectors-laser-jammers/product-registration/
20
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 18
Our Promise
TO EXCEED...
Customer expectations through the pride and dedication of our
strong team of caring and talented employees by being the “Model
of Excellence” in the entire industry on every level — from innovative
product design and flawless manufacturing to knowledgeable sales
and total customer service.
TO PROVIDE...
The most superior and progressive radar detectors and laser jamming
solutions on the worldwide market with guaranteed performance by
delivering tomorrow’s solutions today through the most advanced
technology systems and state-of-the-art radar detection defense.
TO ENSURE...
The total commitment of our entire staff to all customers before,
during, and after the sale with personalized direct 24/7 customer
support — and going the extra mile with product selection and
usage assistance in step with individual needs to achieve the most
dependable radar detection performance and success.
*PLATINUM 360_200 OWNERS .qxp_Layout 1 3/23/20 3:13 PM Page 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

K40 K40-200 Owner's manual

Brand
K40
Model
K40-200
Category
Radar detectors
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents