DayMark Road Warrior User manual

Brand: DayMark

Model: Road Warrior

Type: User manual

DayMark Road Warrior is an electric bicycle that provides a convenient and economical way to travel around town. With its electric motor, the Road Warrior can travel at speeds up to 20 mph, making it a great option for commuting or running errands. The bike also features a throttle for easy acceleration and deceleration, as well as front and rear brakes for safe stopping. Additionally, the Road Warrior has a range of up to 40 miles on a single charge, making it a great choice for longer trips.

Safety

When operang the Road Warrior please make sure you adhere to the following:

• Always wear a helmet when riding the Road Warrior.

• Always check your mirrors and blind spots when operang the vehicle.

• Turn on headlights when in need of addional visibility.

• Make sure that your baery power is sucient before you go out to ride.

• Addional passengers should always wear a helmet.

• Obey all laws of the road.

• Periodically charge the unit when not in use for long periods of me

• If you bring your charger avoid shaking / raling charger while riding.

• Do not over charge the baery by leaving the charger in the charging port. Once

the baery is fully charged remove the charger immediately.

• Do not try to operate the unit while charging.

• Do not let anyone uner the age of 16 years old operate this vehicle.

• Do not make sharp / abrupt turns at high speeds to avoid pping.

• Do not operate under the inuence of any use of drugs or alcohol

• Do not completely submerge the unit in water

• Do not operate in harsh weather condions.

For any quesons or concerns please call

1-800-649-9320 or visit www.daymak.com

About Daymak

Daymak is one of Canada’s largest Alternave Vehicle providers. We design, engineer,

manufacture, import and repair everything from recreaonal dirt bikes, go-karts and

electric golf cars to alternave transportaon soluons such as e-bikes electric scooters.

Our electric bicycles represent an energy-ecient and eco-friendly alternave for

people who need to get around the city. They greatly increase the praccality of bicycle

transportaon in urban centres. Cosng only a few cents to charge, an e-bike can make

city life more convenient and much less expensive.

While there are many new Green technologies that are sll in their infancy, electric

bicycles have been developing over the last 40 years or more. E-bike technology has been

dramacally rened since the introducon of the rst custom-conversion bicycles. Today,

electric bicycles are a supremely reliable and aordable means of transportaon.

Daymak is constantly developing new eco-friendly alternave transportaon strategies,

led by its own Research and Development department in Toronto, Canada. We are always

improving our products. Our innovave in-house engineering and quality tesng provide

customers with many new kinds of reliable, eco-friendly vehicles, designed to help change

the lives of our customers and the world.

Daymak warranes, services, and stocks parts for everything it sells. We support our

products. Please feel free to visit our website. You’ll nd the latest in cool transportaon

soluons, support for the products you’ve purchased and contact informaon.

Introduction

E-Bikes

Using an electric bicycle is a great way to ride around town conveniently and economically.

E- Bikes represent a natural progression in the development of urban transportaon.

Using only small amounts of electricity, e-bikes have the potenal to radically reduce the

amount of polluon in our cies. They are also very quiet, so they do not add to the high

levels of noise polluon which we oen take for granted. They are easy, and usually free

to park. They are unobtrusive and highly praccal addions to the urban landscape.

E-bikes are also inexpensive. They (currently) require no registraon, no insurance, no

licence and do not incur parking charges. Compared to internal combuson engines, the

engines in electric vehicles have fewer moving parts and require far less maintenance.

Your Daymak e-bike is the result of Daymak’s years of experience, the highly trained

technical skills of our sta, and careful ongoing design work by our engineers. We hope

you enjoy using this product and welcome any feedback that you may have.

New Laws

Most provinces in Canada, most states in the U.S.A, the United Kingdom and many

European countries have new laws that permit cyclists to use electric motors to assist the

regular operaon of bicycles. Please check with your provincial or state government to

learn about your local laws.

Liability

Daymak does not assume any liability for damages, loss of prots, or claims from third

pares due to improper use of this product. Daymak does not assume any liability for

damages due to problems with the product resulng from service by a third party that is

not cered by Daymak.

The informaon in this guide may be subject to change without noce. For the latest

informaon available, please contact your local Daymak dealer or visit our website.

We have taken all possible measures to ensure the accuracy and completeness of the

informaon in this guide. However, if you do nd anything missing, incomplete or wrong,

do not hesitate to contact us.

Table of Contents

• SAFETY 2

• ABOUT DAYMAK 3

• INTRODUCTION 4

• PART DIAGRAMS 6

• RIDING INSTRUCTIONS 7

• THE BATTERY 12

• CHARGING YOUR E-BIKE 13

• UNDERSTANDING YOUR VOLTAGE 14

• CHARGING THE ROAD WARRIOR 15

• OPERATION 17

• DISPLAY 20

• ELECTRONIC EXHAUST 22

• PEDALS 23

• BRAKES 2 3

• TECHNICAL DATA 24

• VEHICLE IDENTIFICATION NUMBER (VIN) 25

• MAINTENANCE AND TROUBLESHOOTING 26

• EBIKE MAINTENANCE 28

Part Diagrams

Diagram 1: Road Warrior

This diagram illustrates the various parts of your bicycle. Please note that many of these

parts are not user-serviceable and should be repaired only by trained professionals. This

is especially true of the electrical systems and the mechanical components.

1. Igni on

2. Display

3. Mirrors

4. Thro le

5. Brakes

6. Headlight

7. Shocks

8. Riewa

9. Kickstand

10. Footpegs

11. Pedals

12. Motor

13. Electronic Exhaust

14. Seat

15. Turn Signals

Riding Instructions

This guide assumes that you already know how to ride a standard bicycle. Before you try

to ride an electric bicycle, you should be very familiar with controlling and balancing a

normal bicycle.

Cauon

If you do not have cycling experience, an e-bike is too dangerous to ride. Do not begin

learning to ride a bicycle using an e-bike.

Important Notes

• Ebikes are Fast! E-bikes are capable of traveling at higher speeds than many bicycle

riders are accustomed to. Use cauon at all mes, especially when travelling in mixed

trac. Always take into account driving and traveling condions.

• Obey the Law. Be sure to follow all provincial and city trac laws. This includes

obeying stop signs, checking carefully when turning, and riding defensively.

An e-bike is a motorized vehicle, even though it is classed as a bicycle. You must

follow the law.

• Stay Sober. Never ride your bicycle while intoxicated. An e-bike is capable of

traveling faster than a normal bicycle, and you should always be in control of it.

• Share the Road. Be careful in mixed trac. Let vehicles that are faster than you

• Overtake you and give ample room for vehicles travelling slower.

Items to Carry with the Electric Bike

It is a good idea to carry the following items with you at all mes when you ride your

e-bike.

• The charger, to charge the bike in case the baery power runs out.

• 30 Amp Fuse, spares for the baeries, in case the fuses blow (if applicable).

• A lock, to secure your e-bike when you park it.

• A helmet, as required by safety laws.

Inspecting your Electric Bike

Always inspect your e-bike before you ride it, to make sure its safety features are

operang properly. Many accidents can be avoided with roune inspecons. Once you

are comfortable with your e-bike, you will be able to detect small changes in the way it

feels. If anything changes between uses, make sure to have it properly examined. Also, be

sure to listen for changes in the sounds your e-bike makes over me. Any mechanical or

power issues may have eects on the sounds the bicycle makes.

Holding the Handlebars

As with a normal bicycle, place your ngers over the brake levers, using the palms of your

hand and your thumbs to wrap around and under the handlegrips. Doing this allows you

to acvate the brakes easily, by squeezing your hand, in case you have to stop quickly. This

is the safe way to control your electric bicycle.

Turning your E-bike On and Off

To turn on your e-bike, insert the key into the “ignion”, located just below the dash

board, and turn the key to the right. When your e-bike is acvated, the power indicator

will light and the baery charge indicator will jump, showing you how much power your

e-bike has. To turn o the e-bike, simply turn the key to the le, and remove the key.

Warning

When you acvate the e-bike, the electrical system becomes live. Do not try to aect

changes to the E-Bike (such as removing the baery or repairing electrical components)

while the E-Bike is acvated. Turn the E-Bike o and remove the key before you aempt

to access any of the electrical components. Also, the baery carries a signicant electric

charge and can injure people if not treated properly and with respect.

Accelerating and Decelerating

The throle is found on the right-side hand grip on the handlebars. Turn rotate the grip

counterclockwise (towards from you) to accelerate. To decelerate, release the grip (turn

it away from you). Don’t over-rotate the accelerator, as this could damage the baery and

electrical components.

Warning

Do not acvate the accelerator unl you are seated on the bicycle and are ready to

accelerate. The e-bike can easily escape from your control, possibly injuring you or others,

and the e-bike may be damaged by being dropped.

Stopping

Your e-bike has two sets of brakes, at the front and at the rear. The levers aached to

the handlebars, on the le and right, acvate the brakes. Pull the levers toward you to

acvate the brakes.

You can use both brakes to come to a stop more quickly, or you can use one of the brakes

to come to a gentle stop, depending on your riding needs at the moment. When the

brakes are acvated, the power to the engine is automacally turned o, unl you release

the brakes. This allows you to stop safely.

Safety Tips

• When you are traveling in wet weather, water may cause your brakes to funcon

less eciently because it reduces fricon between the brake pads and the wheels.

• Take care to slow down and give yourself more room to stop or slow if necessary.

• It is a good idea to have your brakes and brake pads checked regularly. The brake

pads will eventually wear down through fricon, and aer signicant use will have to

be replaced.

• Engage the rear brakes rst before the front brakes to avoid ipping the unit.

Signalling

The Horn

The e-bike has a horn. The horn buon is on the le handlebar. Simply press it to acvate

the horn.

Turning Signal Lights

Your e-bike has turn signal lights. The turn signal acvator is on the le handlebar. Push

it le or right to acvate it to indicate that you are turning in the appropriate direcon.

Lights

The headlight and tail light are useful features when you are riding at night or in dark areas.

They radically improve your safety in mixed trac. The lights on your e-bike consume

some electricity. Keeping them on may reduce the maximum distance you can travel on

one charge by about 5 %.

Pedaling

This e-bike is designed to be a motor-assisted bicycle. You can use the motor by itself,

but ideally, you can work with the motor by pedaling. This increases the distance you can

travel on your e-bike, because it assists the motor and reduces the amount of electricity

you draw from the baery.

Riding in Wet Weather

Your e-bike is designed to funcon in wet condions, such as when it is raining. However,

because the motor is on the rear wheel, it is easy to slip when moving at high speeds. If

it is very wet, be sure to avoid high speeds. When you are traveling in wet weather, water

may cause your brakes to funcon less eecvely because it reduces fricon between the

brake pads and the wheels. Take care to slow down and give yourself more room to stop

or slow if necessary.

The Motor and Water

Your e-bike is not designed to be immersed in water. Always ensure that the water level

does not go above the middle of the re, to prevent water from geng inside the motor.

Water in the motor can cause short-circuits and may damage the electrical systems in

your e-bike.

Riding in Cold Weather

Your e-bike is designed to operate year-round. However, in very cold condions or when

there is a lot of snow or slush on the ground, it is possible for the motor in the e-bike

to get wet or for the brakes to funcon less eecvely, just as it can happen in wet

weather. Below 10 degrees Celsius, the baery will not work as well as it would in warmer

temperatures. While Lithium-Ion baeries perform beer than Lead-Acid baeries in

temperature extremes, both will experience reduced performance in cold temperatures.

Also, riding the e-bike in cold temperatures may require you to replace the baery sooner

rather than later.

Maximum Load

Do not exceed the maximum load capabilies of your e-bike. You can nd the exact loading

capacity listed in the technical specicaons in this guide.

If you exceed the maximum load, the performance of the bike will suer.

Exceeding the maximum load of your e-bike could cause damage to the shocks, to the

mechanism and, ulmately, even to the frame. It could also cause your motor to work too

aggressively, and may cause it to burn out.

Disconnecting the Circuit Breaker

When the circuit breaker is disconnected, all power from the baery to the e-bike is

blocked. This is useful if you are going to store your e-bike or if it is damaged and you wish

to bring it to be serviced.

Note: The circuit breaker must be on for the alarm system to work. Do not leave the

circuit breaker o in an unsafe locaon if you are worried about the.

Long-Term Storage of your E-bike

If you are storing your bike for a long period, disconnect the circuit breaker. This is a safer

way to store the electric bicycle, as it prevents accidental acvaon of the e-bike and

makes it impossible to acvate it even with the key.

Please see the secon tled “The Baery” for instrucons on baery maintenance while

your e-bike is being stored.

The Battery

This secon details what you need to know about the baery that powers your e-bike.

Always remember to treat your e-bike’s electrical systems with respect.

Battery Power

The dashboard has a baery charge indicator. When the e-bike is acvated, the guage

will jump and indicate the currently available baery power. If the power has dropped

signicantly, you should charge your e-bike.

Distance and Power

Your baery has the capacity to carry you anywhere from 35+ km before it must be

recharged. The ability of your baery to power your bicycle depends on many variables.

These variables include the weight of the rider, the prevailing wind resistance, the rider’s

driving habits, the presence of steep hills and inclines, and other issues such as proper air

pressure in the res.

Saving Power

If you are traveling long distances, you can save a lot of electricity by using beer driving

habits:

• Coasng: When going downhill or over long, at road surfaces, try using your e-

bike’s momentum and allow it to coast, without drawing power from the motor.

• Stopping and Starng: Try to avoid stop and go movements. The motor draws

more power when starng from a full stop.

• Weight: Remove unnecessary weight from the bike. This reduces the amount of

power the motor must draw.

• Air Pressure: Make sure your res have the proper air pressure. Proper pressure

reduces drag on the res and radically increases the eciency of any vehicle.

• Head and Tail Lights: Turn o the lights to conserve power, if it is safe to do so.

The lights will reduce the distance you can travel by about 5%.

• Pedalling: When accelerang from a full stop, you might want to try pedaling to

help acceleraon.

Charging your E-Bike

Charging your e-bike is a simple process. You require the following:

• The charger that came with your e-bike.

• A 110V household electrical outlet.

Charger Warning

Only use the chargers that were supplied with your e-bike. Using chargers that do not have

specicaons idencal to those which came with the e-bike could irreparably damage

your e-bike’s baery and electrical systems, and may cause injury.

To charge your e-bike, follow these steps:

1. Turn o the e-bike and remove the key from the “ignion.”

2. Plug the female end of the charger cable into the charging slot on the e-bike.

3. Plug the male end of the charger power cable into your wall socket. This should be

a110v household electricity supply. You can also use a portable generator, if necessary,

but make sure it provides 110V current.

4. Allow the e-bike’s baery to charge for the appropriate amount of me

(6-12 hours).

5. Disconnect the charger when the LED light on the charger is green. The baeries

have been fully charged.

If your charger’s LED status light does not change from red to green over an extended

period of me, for perhaps more than 14 hours, and the baery is very hot, the baery

or charger may need replacing. Stop charging and bring both to your Daymak dealer

immediately. Do not charge the baery.

Understanding your voltage

Electric scooters primary power is displayed on your unit as a voltage. This number in

short shows how powerful your unit is, and as it dips down when the unit will no longer

be able to perform. Depending on your unit’s voltage and baery type (Lithium vs Lead

Acid) will eect the range of voltage between what is fully charged and when it exceeds

the low voltage threshold.

Low Voltage Threshold

Your unit will try to protect the baery by prevenng the motor from drawing power below

the Low Voltage Threshold. By doing this it will signicantly increase the life expectancy of

your unit. If you nd that your motor starts cung o at a certain speed or not engaging

at all it may be because your voltage is dropping past the threshold point and needs to be

charged. To see what your voltage threshold you can check on it via the bluetooth APP (if

applicable) and you can check it out using this chart.

Voltage Chart

LITHIUM Full/Low Voltage Reading

Depending on the way your lithium baery’s composion will impact what the low

voltage and full charge reading should be. Underneath each reading on the above chart

shows a number and a “S” this represents how many series are in your baery pack. To

know the exact series of your baery contact your local Daymak dealer.

Charging the Road Warrior

First take the charger that came with your Road Warrior and plug it into the the wall. Once

you have done that locate the charging port of the Road Warrior located on the inside of

the glove compartment. You must unlock the glove compartment with your keys and look

for a plug that is covered up. It will be covered up as seen below:

Once the bike is charging the charger will glow red. When the unit is fully charged the

charger will glow green and then your bike is ready to go.

Warning

Do not leave the Road Warrior charging for long periods of  me a er it is fully charged.

Once the bike is charged unplug it ASAP.

Accessing your Circuit Breaker

To prevent surges, we have installed a circuit breaker.

If you are unable to get power to your bike more

than likely your circuit breaker has been triggered

and needs to be switched to the on posi on.

To do this:

Put the key in glove box to unlock it. It is located

inside the glove box underneath the charging port

Battery Care

Follow these suggesons to maintain your baery’s opmal performance. If you do not

follow these suggesons, your baery may lose its ability to maintain a charge and might

have to be replaced sooner than would otherwise be necessary.

• Charge it: Charge your baery immediately aer riding it.

• Full Charge: Do not allow the baery to run down completely and lie in storage

without a charge. This signicantly reduces the baery’s lifespan and may cause

damage.

• Keep it Charged: When being stored, charge the baery occasionally to make

sure its power supply does not run down. Charging it once every 21 days should be

sucient.

• Storage Condions: Store the baery on a at, cool, dry surface. Do not allow the

baery temperature to drop below 10 degrees Celsius for extended periods of me.

Warning

DO NOT place your Lead-Acid baery on concrete. Concrete drains the baery’s power

and will neutralize the lead-acid. Placing the baery on concrete for any length of me

will likely result in the baery being drained of power and possibly losing its ability to

store electricity.

Cold Weather and your Battery

Below 10 degrees Celsius, the baery will not work as well as it would in warmer

temperatures. While Lithium-Ion baeries perform beer than Lead-Acid baeries in

temperature extremes, both will experience reduced performance in cold temperatures.

Also, repeatedly riding the e-bike in cold temperatures may cause your baery to have to

be replaced sooner.

Replacement and Disposal

Aer approximately 300 charges, a lead-acid baery will need to be replaced. A lithium-

ion baery will last approximately 1000 charges. When the baery has to be replaced,

you will noce that your baery cannot carry as much of a charge as it could inially.

Contact your local Daymak dealer to purchase a new baery.

When replacing your baery, dispose of it at a proper municipal baery recycling facility.

If none is available, please contact your local Daymak dealer.

Operation

Right handle bar

1. Lights - The far right posi on is all lights o .

The Middle Posi on is just running brake lights

and far le posi on is all lights on.

2. Flasher - Press this to  ash your headlights

on and o quickly.

3. Speed Switch - Turn this to easily monitor

your speed. Speed 1 - Slowest speed / Longest

Range Speed 3 - Fastest Speed / Shortest Range

4. Cruise Control - While the unit is running

press this bu on to remain at this speed without

the thro le being rotated. To disengage cruise

control just hit either brake lever. *Manual cruise

must be on in bluetooth se ngs*

5. Thro le - Turn this towards you to engage

the motor to go!

Left handle bar

1. MP3 / MPEG Controls - See next page for

more detailed informa on

2. USB Plug - See next page for more detailed

informa on

3. Horn - Press this to honk the horn

4. Turn Signals - Press this to the le to indicate

turning to the le . Press the middle white bu on

once the turn is complete.

5. High Beam / Low Beam - Press up to angle

your lights hight and press down to angle the

lights down.

Modes

1. Radio - Once on radio mode, on you display will show the frequency that it is on.

Use your next song / previous song bu ons to change the radio sta on.

2. Bluetooth - To connect to the unit, look for YEK-BT*** on bluetooth devices

screen on your smart phone. Once you ask to connect it will ask for a password.

This password is 0000 . Once connected and on the Bluetooth mode, you can

Bluetooth / Radio / MP3 / Video

3. MP3 - If you don’t want to connect via Bluetooth to your smart device for whatever

reason, you cacn load MP3’s onto a USB drive and plug it in. Then once you select MP3

it will automa cally play the songs o that.

4. Video - You can also watch videos on the display! By selec ng the video func on

and loading an MPEG  le onto a USB key you can watch videos on the display!

MP3 / Radio / MPEG Controls

The Road Warrior comes with a MP3 / Radio / Video

player.

1. Volume Up / Next Song - Press this button

to play the next video / song or change the

radio station. Press and Hold this to increase

the volume.

2. Press this button to switch between

which device it is to play through:

Bluetooth / Radio / MP3 / Video.

3. Volume Down / Previous Song - Press this

button to play the previous video / song or

change the radio station back. Press and hold

this to decrease the volume.

4. Press this to turn on the power or stop

playing a song/ video.

5. USB Port, plug a usb stick to utilize the video

/ MP3 function.

When opera ng the Road Warrior, insert the keys

into the igni on seen here and turn it clockwise.

Once on, simply turn the thro le towards

you to ride.

Keys

The Road Warrior comes with two sets of keys and

two remotes. There are four bu ons on the remote:

1. Set Alarm - This bu on will set the alarm.

A er pressing it wait for 5 seconds. A erwards

if someone moves the bike the alarm will sound.

2. Remove alarm - This will disengage the

alarm. Use this before riding your bike. **Also

disengeages remote start*.

3. Panic Bu on - This will automa cally set the

alarm o .

4. Remote Start - Press this twice to start the

bike without using the keys. Press the remove

alarm bu on (2) to disengage the remote start.

Steering Lock

When you are trying to engage the wheel lock:

Turn the handlebars so that it is poin ng to the le

and then push the key in a bit further and turn to

counter clockwise. This feature will allow you to

prevent the .

Note: The ﬁ le format must be MPEG 2 with a maximum resolu on of 480p and a

perferred resolu on of 852 x 480

Warning : Do not ride the vehicle while videos are playing as it can be distrac ng and

can lead to injuries.

Display

The Road Warrior display shows all the metrics you

need when riding.

1. Battery Meter - This gauge shows how much

power your bike has left and will decrease as

you rider.

2. Voltage - This is a numeric reading of

the battery meter. A full charge should be

approximately 82-84V.

3. Trip Meter - Shows how far you have

travelled since this has been turned on,

4. Odometer - Shows the total distanced

travelled on this machine

5. Speedometer - Shows the current speed/

6. Power / Mode - Shows weather the MP3

device is on or oﬀ and shows what mode it

is on. The four modes are Radio / Bluetooth

/ MP3 / Video

Page is loading ...

DayMark Road Warrior User manual

DayMark Road Warrior User manual

DayMark Road Warrior User manual

Other documents