Haier HDBL655AFB Installation Instructions Manual
- Category
- Dishwashers
- Type
- Installation Instructions Manual
This manual is also suitable for
24" Built-In Dishwasher
Installation Instructions
HDBL655AFS
HDBL655AFW
HDBL655AFB
1
TABLE OF CONTENTS
DISHWASHER SAFETY ........................................................................................ 2
INSTALLATION REQUIREMENTS ......................................................................... 3
Tools and Parts ............................................................................................................... 3
Location Requirements .................................................................................................5
Product Dimensions ...................................................................................................... 6
Drain Requirements ....................................................................................................... 7
Water Supply Requirements ......................................................................................... 8
Electrical Requirements ................................................................................................ 9
Wire Routing and Connection Requirements ............................................................. 10
INSTALLATION INSTRUCTIONS ........................................................................ 11
Step 1- Check Door Balance .......................................................................................11
Step 2- Adjust Leveling Legs ......................................................................................12
Step 3- Remove Kick Plate .........................................................................................12
Step 4- Install 90° Elbow .............................................................................................. 13
Step 5A- Prepare Cabinet Opening Using Existing Utility Hookups ......................... 13
Step 5B - Prepare Cabinet Opening Where
There Are No Existing Utility Hookups .......................................................................16
Step 6- Position the Water Line and House Wiring ....................................................19
Step 7 – Insert Drain Hose Through Cabinet ..............................................................20
Step 8 – Slide Dishwasher Partially Into Opening .......................................................21
Step 9 – Position Dishwasher Under Countertop .....................................................22
Step 10 - Level the Dishwasher ..................................................................................22
Step 11 - Connect Power Supply ...............................................................................23
Step 12 - Connect to Water Supply ............................................................................26
Step 13 - Connect to Drain ..........................................................................................27
Step 14 - Secure Dishwasher ...................................................................................... 28
Step 15 - Pre-Test Checklist ........................................................................................30
Step 16 - Test Dishwasher ..........................................................................................31
2
DISHWASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and
on your appliance. Always read and obey all safety messages.
DANGER
WARNING
CAUTION
This is the safety alert symbol.
This symbol alerts you to potential hazards that can
kill or hurt you and others. All safety messages will
follow the safety alert symbol and either the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
An imminently hazardous situation. You
could be killed or seriously injured if you
don’t immediately follow instructions.
A potentially hazardous situation
which, if not avoided, could result in
death or serious bodily injury.
A potentially hazardous situation
which, if not avoided, may result in
moderate or minor injury.
All safety messages will tell you what the potential hazard is, tell you
how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Failure to follow these instructions can result in serious injury or cuts.
3
YOU NEED TO:
•
Slowly open dishwasher door while someone grasps the rear of the
dishwasher. Remove the drain hose and lower rack. Close dishwasher
door until latched.
•
•
dishwasher must be installed to meet all electrical and plumbing national
and local codes and ordinances.
•
The dishwasher must be installed to allow for future removal from the
enclosure if service is required.
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
PARTS SUPPLIED
wood screws
2 - Color matched kick plate
screws
2 - Side mounting clips
2 - Top mounting clips Hose clamp Drain hose
PARTS NEEDED
Ferrule, compression nut
external threads on one end.
water supply line).
Thread seal tape
3 UL listed wire nuts Waste tee
(house plumbing, if applicable)
Electrical cable
(power cord, if applicable)
4
Air gap for drain hose
(if required)
Hose clamps
Strain relief Coupler (extending drain line,
if applicable)
TOOLS NEEDED
Phillips screwdriver Level
Flashlight Measuring tape
Carpenters square Safety glasses Bucket
Gloves
TOOLS NEEDED - NEW INSTALLATION ONLY
Tubing cutter Hole saw set Drill and bits
5
LOCATION REQUIREMENTS
IMPORTANT:
•
Do not run drain lines, water lines or electrical wiring where they can interfere
with or contact dishwasher motors or legs.
•
The location where the dishwasher will be installed must provide clearance
•
•
•
The dishwasher must be fully enclosed on the top, sides and back and must not
support any part of the enclosure.
•
The dishwasher must be installed so that the drain hose is no more than 10 ft in
length for proper drainage.
OPENING DIMENSIONS
•
•
the dishwasher door and the wall or cabinet.
24" (61.0 cm)
90°
90°
34" to 35"
(86.4 cm
to 88.9 cm)**
3"
(7.6 cm)
18"
(45.7 cm)
3"
(7.6 cm)
1¾"
(4.4 cm)
3"
(7.6 cm)
6"
(15.2 cm)
* Make sure water line, wires and drain hose are within the shaded area.
NOTE:
may be accomplished by adjusting the toekick and leveling legs.
6
•
to fully open.
25
5
/8"
(65.1 cm)
a
b
c
a Countertop
b Dishwasher
c Clearance for Door Opening
2" Minimum
PRODUCT DIMENSIONS
Side View
25⁹⁄₁₆" (65 cm)
33¾"
(85.7 cm)
7
Rear View
25⁹⁄₁₆" (65 cm)
DRAIN REQUIREMENTS
•
Use the new drain hose supplied with your dishwasher. If this is not long enough,
use a new drain hose with a maximum length of 10 ft (3.05 m) that meets all
current AHAM/IAPMO test standards, is resistant to heat and detergent, use
the two hose ends. Secure the connection with two clamps.
•
Dishwasher must be connected to waste line with an air gap (not supplied) or
32"(81.3 cm) minimum high drain loop, depending on local codes and ordinances
IMPORTANT: Failure to provide the proper drain connection height with air gap
or 32" (81.3 cm) minimum high drain loop will result in improper draining of the
dishwasher.
•
An air gap must be used if the waste tee or garbage disposal connection is less
a
a Air Gap
•
•
Do not connect drain lines from other devices to the dishwasher drain hose.
8
WATER SUPPLY REQUIREMENTS
•
The pressure of the water coming from the hot water supply line must be 20-
•
The water connection is located on the left front side of the dishwasher. Install
as shown and extend it forward at least 18" (45.7 cm) from the rear wall.
NOTE: Routing the water line through the left side of cabinet opening will make
water connection easier.
b
a
c
e
d
4" (10.2 cm)
fr
om cabinet
18" (45.7 cm)
from wall
3" (7.6 cm)
from floor
a Hot Water Supply
b
c 1½" (3.8 cm) Dia. Hole
d Hot Water Line
e Cabinet Face
•
The hot water line may either pass through the same hole as the electrical cable
and drain hose, or cut an additional 1½" (3.8 cm) dia. hole for the water line.
•
If the electrical cord has a three prong grounded plug, it cannot pass through the
same hole as the hot water line and drain hose. You must cut a separate hole for
the electrical cord.
•
Adjust the water heater to a water temperature of 120°F to 150°F (49°C to
65.5°C).
9
ELECTRICAL REQUIREMENTS
WARNING
Electrical Shock Hazard
Installation and service must be performed by a qualified installer or
service agency.
Always disconnect the power before servicing this unit.
This appliance must be properly grounded.
Failure to do so could result in death, fire, or electrical shock.
IMPORTANT:
•
The dishwasher must be supplied with 120 volt, 60 Hz, AC-only, 15 or 20 amp.,
fused electrical supply.
•
Wiring must be 2-wire with ground.
•
If the electrical supply does not meet the above requirements, call a licensed,
•
size are adequate and in conformance with the National Electrical Code, ANSI/
NFPA No. 70-latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from the website
www.nfpa.org or:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
Grounding Instructions:
•
The dishwasher must be connected to a grounded metal, permanent wiring
system, or an equipment grounding conductor must be run with the circuit
conductors and be connected to the equipment grounding terminal or lead on
the dishwasher.
10
WIRE ROUTING AND CONNECTION REQUIREMENTS
Cabinet Preparation and Wire Routing
•
Electrical connection is on the right front side of the dishwasher.
NOTE: Wiring the dishwasher will be easier if you route wire into the cabinet
opening from the right side.
•
the shaded area.
•
Wiring connections may pass through the same hole as the drain hose and hot
water line or cut an additional 1½" (3.8 cm) dia. hole to admit the electrical cable.
NOTE: The hole must be free of sharp edges. If the cabinet wall is metal, the
edge of the hole must be covered with a bushing/grommet.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
a
a Terminal Box
•
For direct wire connections the cable must be routed as shown in the following
graphic. Cable must extend a minimum of 24" (61 cm) from the rear wall.
•
grounding type receptacle. The power-supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the under counter space in which
the appliance is to be installed.
a
b
c
d
3" (7.6 cm)
from Cabinet
24" (61.0 cm)
minimum
from Wall
a 1½" (3.8 cm) Dia. Hole (Max.)
b Ground
c Black
d White
11
INSTALLATION INSTRUCTIONS
STEP 1- CHECK DOOR BALANCE
With another person holding the dishwasher to prevent it from tipping, open the
door slowly. If the door drops when released, increase the spring tension. If the door
closes when released, decrease the spring tension.
To adjust the spring tension:
1. Pull the spring adjustment pin out of the holes. Insert the pin into the next
highest or lowest hole.
2. Move the spring adjustment pins to the same holes on both the left-hand and
right-hand sides.
3. Retest the door, and continue moving the spring adjustment pin until the door is
balanced.
Increase
Decrease
12
STEP 2- ADJUST LEVELING LEGS
1. Measure the dishwasher height and the height of the opening from the
lowest point).
2.
height of the opening.
a
a Adjust to Installation
Height
STEP 3- REMOVE KICK PLATE
1. Using a screwdriver, remove the screws attaching the kick plate to the cabinet.
2.
a
a 2 Kick Plate Screws
13
STEP 4- INSTALL 90° ELBOW
WARNING
Excessive Weight Hazard
Use two or more people to move and install dishwasher.
Failure to do so can result in back or other injury.
1. Using two or more people stand the dishwasher upright, and position it in front
of the opening.
2. Wrap the 90° elbow with thread seal tape, and then install it onto the water valve.
NOTE:
tighten the elbow.
3. Position the end of the elbow to face the bottom right of the dishwasher.
STEP 5A- PREPARE CABINET OPENING USING
EXISTING UTILITY HOOKUPS
•
Follow the steps in this section if you are installing the dishwasher in an existing
cabinet opening with utility hookups.
•
If you are installing the dishwasher in a cabinet opening that does not have
hookups, follow the instructions under “Prepare Cabinet Opening Where there
1. Check that the water line reaches to the front left of opening where the water
connection will be made.
2. Check that the direct wire reaches to the front right of opening where the
electrical connection will be made.
If the water line and the direct wire reach far enough
into the opening, proceed to the next section
enough, follow the instructions under “Prepare
Cabinet Opening Where there are No Existing Utility
6" (15.2 cm)
water
line
direct
wire
14
INSTALL THE DRAIN HOSE
IMPORTANT:
•
Always use a new drain hose when installing a new replacement dishwasher.
•
through the cabinet to minimize the noise caused by vibration when using the
dishwasher.
1. Connect drain hose to waste tee or garbage disposal using one of the following
methods.
•
Option 1 – Garbage Disposal - With Air Gap
•
Option 2 – No Garbage Disposal- With Air Gap
•
Option 3 – Garbage Disposal - No Air Gap*
•
Option 4 – No Garbage Disposal - No Air Gap*
*an air gap is recommended
Option 1 – (Garbage Disposal - With Air Gap):
1. Remove the garbage disposal knockout plug. Cut end of drain hose if needed (do
not cut ribbed section).
2. Attach drain hose to air gap with screw-type clamp. If the drain hose was cut, use
a 1½" to 2" (3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw type clamps* to connect air
gap to garbage disposal inlet.
This connection must be before the drain trap and at least 20" (50.8 cm) above the
a
b
f
c
d
e
g
h
a Drain Hose - Cut Here if
Needed
b Screw-Type Clamps
c Air Gap
d Screw-Type Clamp
e Drain Hose
f Rubber Hose Connector
g Garbage Disposal Inlet
h Drain Trap
*Parts available from local plumbing supply store.
15
Option 2 – (No Garbage Disposal- With Air Gap):
1. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was
cut, use a 1½" to 2" (3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw type clamps* to connect air
gap to garbage disposal inlet.
This connection must be before the drain trap and at least 20" (50.8 cm) above the
a
b
f
c
d
e
g
h
a Drain Hose - Cut Here if
Needed
b Screw-Type Clamps
c Air Gap
d Screw-Type Clamp
e Drain Hose
f Rubber Hose Connector
g Waste Tee
h Drain Trap
*Parts available from local plumbing supply store.
Option 3 – (Garbage Disposal - No Air Gap):
1. Remove the garbage disposal knockout plug. Do not cut end of drain hose.
2. Attach drain hose to garbage disposal inlet with screw-type clamp.
3. Use a rubber hose connector* with screw-type clamps* to connect garbage
disposal inlet.
This connection must be before the drain trap and at least 20" (50.8 cm) above the
be looped up and securely fastened to the underside of the counter. “See “Drain
b
a
c
d
a Drain Hose
b Screw-Type Clamp
c Garbage Disposal Inlet
d Drain Trap
* Parts available from local plumbing supply store.
16
Option 4 – (No Garbage Disposal - No Air Gap):
1. Cut end of drain hose if needed (do not cut ribbed section).
2.
This connection must be before the drain trap and at least 20" (50.8 cm) above the
be looped up and securely fastened to the underside of the counter. See “Drain
a
b
c
d
e
a Drain Hose - Cut Here
if Needed
b Screw-Type Clamps
c Drain Hose
d Drain Trap
e Waste Tee
*Parts available from local plumbing supply store.
STEP 5B - PREPARE CABINET OPENING WHERE THERE
ARE NO EXISTING UTILITY HOOKUPS
INSTALL ELECTRICAL CONNECTION
WARNING
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit breaker box
before installing dishwasher.
Failure to do so can result in death or electrical shock.
Method 1 - Direct Wire
1. Drill a ¾" (1.9 cm) hole into the right-hand cabinet, or the right-hand side of the
locations.
17
NOTE: Wiring the dishwasher will be easier if the wire is routed into the opening
from the right-hand side.
ba
a Preferred Locations
b Optional Locations
2. Remove sharp or rough edges by smoothing or covering the edges of the hole
that the wiring passes through.
Wood Cabinet - Sand edge of hole until smooth.
Metal Cabinet - Cover edge of hole with grommet (not provided).
3. Route cable from power supply through cabinet hole (cable must extend to the
cabinet opening.
Method 2 - Power Supply Cord
IMPORTANT: A mating 3 prong, ground-type wall receptacle is required in a cabinet
next to the dishwasher opening.
1. Drill a 1½" (3.8 cm) hole in the cabinet rear or side. Preferred and Optional
locations are shown in the following graphic.
2. Smooth edges of hole for power cord.
Wood Cabinet - Sand edges of hole until smooth.
Metal Cabinet - Cover edges of hole with grommet included with power supply
cord kit (not provided).
ba
a Preferred Locations
b Optional Locations
18
INSTALL THE WATERLINE
NOTE: Routing the water line through the left side of cabinet opening will make
water connection easier.
1.
locations are shown in the following graphic.
2. Measure to determine the overall length of copper tubing required for the water
line.
3.
ab
a Preferred Locations
b Optional Locations
4. Slowly feed copper tubing through hole in cabinet. Copper tubing will bend and
kink easily, so be gentle. The copper tubing should be far enough into the cabinet
opening to connect it to the dishwasher inlet on the front left of the dishwasher.
a
a Copper Tubing
5.
to get rid of particles that may clog the inlet valve.
6.
INSTALL THE DRAIN HOSE
IMPORTANT: Always use a new drain hose.
1.
to the sink.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Haier HDBL655AFB Installation Instructions Manual
- Category
- Dishwashers
- Type
- Installation Instructions Manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Whirlpool WDF560SAFW Dimensions Guide
-
Maytag MDB7709AWQ - Jetclean Plus 24 in. Dishwasher Dimensions
-
-
Kenmore Elite 66512779K311 Installation guide
-
SMITH SYSTEM 179802 Assembly Instructions
-
LG Electronics LDT6809SS Installation guide
-
KitchenAid KUDH03DT User manual
-
-
-
