Gigabyte GS-SR157L Installation guide

System Installation Guide

GS-SR157L

1U Rack Mount Server

Intel® Pentium Prescot LGA775 Processor Serverboard

Rev. 1001

25A080-0157L-F00

2

GS-SR157L Rack Mount Server

Table of Content

Safety, Care and Regulatory Information................................................4

Contents Packages ................................................................................8

Introduction..............................................................................................8

WARNING!...............................................................................................8

Chapter 1 Features Summary.................................................................9

Chapter 2 System Overview.................................................................11

Chapter 3 System Hardware Installation ...............................................12

Step 3-1: Chassis Removal and Installation ................................................................ 12

Step 3-2: CPU Installation............................................................................................... 13

Step 3-3: Heat Sink Installation....................................................................................... 14

Step 3-4: Memory Installation ........................................................................................ 14

Step 3-5: PCI Expansion Card Installation.................................................................... 15

Step 3-6: Hard Disk Drive Installation ............................................................................ 16

Step 3-7: FAN Duct Removal and Installation.............................................................. 17

Chapter 4 Appearance of GS-SR157L..................................................18

4-1: Front View of GS-SR157L ...................................................................................... 18

4-2: Rear View of GS-SR157L ...................................................................................... 19

4-3: Switch and LED Indicators Introduction ................................................................. 20

4-4: LAN LED Description............................................................................................... 21

4-5 : Connector Icon Description ................................................................................... 22

Chapter 5 Motherboard Layout & Jumper Setting................................23

5-1: GA-8ICXR Motherboard Layout ............................................................................. 23

5-2: Jumper Setting ......................................................................................................... 25

3

Table of Content

Chapter 6 BIOS Setup ..........................................................................26

Main...........................................................................................................28

Advanced Processor Options ........................................................................................ 31

Advanced ...................................................................................................32

Memory Configuration..................................................................................................... 33

PCI Configuration............................................................................................................. 34

I/O Device Configuration................................................................................................. 36

Advanced Chipset Control ............................................................................................. 40

Security ......................................................................................................43

Server.........................................................................................................45

System Management...................................................................................................... 48

Console Redirection........................................................................................................ 49

Boot............................................................................................................52

Exit .............................................................................................................53

7-1: Acronyms................................................................................................................. 56

Chapter 7 Appendix..............................................................................56

4

GS-SR157L Rack Mount Server

Safety, Care and Regulatory Information

Important safety information

Read and follow all instructions marked on the product and in the documentation before you operate

your system. Retain all safety and operating instructions for future use.

* The product should be operated only from the type of power source indicated on the rating label.

* If your computer has a voltage selector switch, make sure that the switch is in the proper position for

your area. The voltage selector switch is set at the factory to the correct voltage.

* The plug-socket combination must be accessible at all times because it serves as the main disconnect-

ing device.

* All product shipped with a three-wire electrical grounding-type plug only fits into a grounding-type power

outlet. This is a safety feature. The equipment grounding should be in accordance with local and national

electrical codes. The equipment operates safely when it is used in accordance with its marked electrical

ratings and product usage instructions

* Do not use this product near water or a heat source.

* Set up the product on a stable work surface or so as to ensure stability of the system.

* Openings in the case are provided for ventilation. Do not block or cover these openings. Make sure you

provide adequate space around the system for ventilation when you set up your work area. Never insert

objects of any kind into the ventilation openings.

* To avoid electrical shock, always unplug all power cables and modem cables from the wall outlets

before removing covers.

* Allow the product to cool before removing covers or touching internal components.

Precaution for Product with Laser Devices

Observe the following precautions for laser devices:

* Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than

those specified in the product's documentation.

* Only authorized service technicians should repair laser devices.

Precaution for Product with Modems, Telecommunications, ot Local Area

Network Options

Observe the following guidelines when working with options:

* Do not connect or use a modem or telephone during a lightning storm. There may be a risk of electrical

shock from lightning.

5

Safety Information

* To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

* Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

* Disconnect the modem cable before opening a product enclosure, touching or installing internal

components, or touching an uninsulated modem cable or jack.

* Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission

limits. Neither the provider nor the manufacturer are responsible for any radio or television interference

caused by using other than recommended cables and connectors or by unauthorized changes or

modifications to this equipment. Unauthorized changes or modifications could void the user's authority to

operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

FCC part 68 (applicable to products fitted with USA modems)

The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among

other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment.

You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may

discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not

practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with

the FCC.

6

GS-SR157L Rack Mount Server

Your telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect proper operation of your equipment. If they do, you will be notified in advance to give you an

opportunity to maintain uninterrupted telephone service.

The FCC prohibits this equipment to be connected to party lines or coin-telephone service.

The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part

68, Sec. 68.381 (c) (3)).

/ for Canadian users only /

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus as set out in the radio interference regulations of Industry Canada.

Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux

appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edicte par

Industrie Canada.

DOC notice (for products fitted with an Industry Canada-compliant modem)

The Canadian Department of Communications label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational and safety

requirements. The Department does not guarantee the equipment will operate to the user satisfaction.

Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the

local Telecommunications Company. The equipment must also be installed using an acceptable method

of connection. The customer should be aware that compliance with the above conditions might not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,

may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system, if resent are connected together. This precaution

may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

7

Safety Information

NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total

load to be connected to a telephone loop which is used by the device, to prevent overloading. The

termination on a loop may consist of any combination of devices subject only to the requirement that the

sum of the Load Numbers of all the devices does not exceed 100.

/ for European users only /

CAUTION

Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent

type recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer’s instructions.

8

GS-SR157L Rack Mount Server

;Chassis ;GA-8ICXR Motherboard (Installed)

;Power Supply (Installed) ;GSMT User’s Manual

;FAN Duct x 1 ;CPU Heat Sink x 1

;Standard Floppy Drive (Installed) ;Silm type CD-ROM drive (Installed)

;Cables (RJ45) ;GS-SR157L System Installation Guide

;Case Handle Kit x 2 ;Driver CD for motherboard driver & utility

;Driver CD for IPMI

Introduction

Welcome to Gigabyte GS-SR157L Rack mount Server System Installation Guide. The guide

provides instructions for configuration hardware for the GS-SR157L your system.

This installation guide will assist you in installing all the essential components for the sever system.

For your protection, please read and undertand all of the safety and operating instructions regarding your

Gigabyte Server and retain for future reference. The procedures in this guidebook assusme that your are

a system or network administrator experienced in installing similar hardware.

Contents Packages

When opening the package, please ensure the system components are not damaged during the shipping.

Using the following checklist to verify the contents. If any component is missing or damaged in the

system, please contact your vendor immediately.

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

WARNING!

9

Feature Summary

Motherboard GA-8ICXR

Processor Supported Supports Intel® Pentium Prescot LGA 775 processor

Intel® Prescot LGA 775 supports 800MHz FSB

L2 cache on-die per processor from 1M

Chipset Intel® MCH E7221 Chipset

Intel® 6702 PXH-V

Intel® ICH6R

System Memory:

Memory Capacity 4 x DDR socket up to 4 GB

Memory Type Un-buffered DDR 333/400

DIMM Size Support 256MB, 512MB, and 1GB memory

Error Correction: Single-bit Errors Correction, Multiple Bit Errors Detection

Expansion Slot 1 Butter-Fly Riser card supports 2 x 64/66~100MHz add-on cards

(3.3V)

1 x Low Profile PCI add-on card (Half-High/Half-Length)

1 x Full-Size add-on card (Full-High/Half-Length)

ATA RAID controller ICH6R

Supports dual ports SATA RAID 0,1

Cooling Fans: 4 X System Fan

1 X Power Fan

Integrated LANs:

Controller Dual Intel® 82541GI GbE

Feature WOL

Integrated Graphics:

Controller Integrated, ATI Rage-XL

Graphics Memory 8MB SDRAM

Mass Storage System 2 x Internal SATA HDD

1 x Standard Type FDD

1 Slim Type CD-ROM

Optional DVD Combo

Chapter 1 Features Summary

10

GS-SR157L Rack Mount Server

Super I/O

Controller ITE IT8712F-A Super I/O

Built-in I/O 1 x Serial port (COM)

1 x USB 2.0 dual-port connector

1 x VGA connector

2 x RJ45 LAN ports

P/S 2 Keyboard and Mouse Connectors

1 x RJ45 on front for console redirection

System BIOS:

BIOS Type Phoenix® BIOS, Multi-boot BBS 1.0 Compliant4Mb Flash Memory

Special Features BIOS HW Monitoring reporting (The values monitored by HW

Monitoring chipset)

Console Redirection via COM ports

Intel® Hyper Threading Support

Resume after AC Back

Wake On LAN

ACPI 1.0 Compliant/ ACPI defined S1, S4, and S5

Server Management Functions: (Optional)

BMC Chip NS IPMI 1.5 controller

Failure Detection IPMI 1.5 specification of Server management

Event Logging 32KB Nonvolatile Memory to Log System Failure Events

Remote Management Follow the IPMI 1.5 specification of Server management

Environment

Ambient Temperature Operating Temperature: 5oC to 35oC

Non-operating Temperature: 0oC to 50oC

Relative Humidity 10-80% operating Humidity at 30o C

Safety Regulations FCC, CE, BSMI, CB, Win2000, 2003 WHQLIPMI 1.5 ( Option)

System Dimention: 427.5mm x 521mm x 42.6 mm

Electrical Power Supply Single Power Supply 250W

11

System Overview

Chapter 2 System Overview

A

B

C

D

E

F

G

H

I

G

J

D

A. Chassis Cover F. ZCR Slot

B. Motehrboard - GA-8ICXR G. HDD Plate

C.Heat Sink H. HDD

D. System Fans I. FDD

E. Riser Card Support J. Power

12

GS-SR157L Rack Mount Server

Please observe the safety information in chapter “Important Safety Information”

Do not expose the server to extreme environmental conditions. Protect it from dust,

humidity, and heat.

Step 3-1: Chassis Removal and Installation

Step 1 Loosen the thumbscrew from the back of the server.

Step 2 Push down the indentation located at two sides of the chassis, and slide toward to remove the

top cover.

Step 3 Reverse Step 1, and 2 to replace the chassis cover.

Chapter 3 System Hardware Installation

Step 2

Note: Before installing CPU, you must remove the FAN duct. For FAN duct removal, please

see Sub-section 3-7 “FAN Duct Removal and Installtion” for detail instruction.

Step 1

Thumbscres

13

Hardware Installation Process

Step 3-2: CPU Installation

Please make sure the CPU type and speed that are supported by the motherboard.

Step 3

Step 1 Step 2

Step 1 Gently lift the metal lever located on the CPU socket to the upper-right position.

Step 2 Remove the plastic covering on the CPU socket.

Step 3 Align the indented corner of the CPU with the triangle and gently insert the CPU into position.

(Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket

in a straight and downwards motion. Avoid twisting or bending motions that might cause

damage to the CPU during installation.)

Step 4 Once the CPU is properly inserted, please replace the plastic covering and push the metal

lever back into its original position.

Step 5 Close the lever, reverse step 1 & 2.

Step 4

14

GS-SR157L Rack Mount Server

Step 3-3: Heat Sink Installation

Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well

remember to apply the thermal conductivity compound on the CPU.

Step 2 Seat the heat sink in the retention modules with the four screws. Installation completed.

Step 3-4: Memory Installation

1. The DIMM slot has a notch, so the DIMM memory module can only fit in one direction.

2. Insert the DIMM memory module vertically into the DIMM slot. Then push it down.

3. Close the plastic clip at both edges of theDIMM slots to lock the DIMM module.

4. When installing the DIMM into the DIMM module, we recommend to populate one DIMM in

Channel A module and one in Channel B module for best performance.

Please note that each logical DIMM must be made of two identical DIMMs having the same

device size on each and the same DIMM size.

5. Reverse the installation steps when you wish to remove the DIMM module.

Step 2

Step 1

15

Hardware Installation Process

Step 3-5: PCI Expansion Card Installation

GS-SR157L provides expansion riser slots for one PCI-X full-height/full-length 64/66~100MHz; and one

with PCI-X low-profile 64-Bit/66~100MHz. To install the peripheral, please go through the following steps.

Note!! Before installing the PCI expansion card, please check the card size limitation. Size limitation

for PCI-X full-height/full-length is 228.5 mm x 91.5 mm; size limitation for Low-Profile Card : 167.5 mm

x 56 mm .

Step 1 Loosen the riser bracket screws.

Step 2 Lift the riser bracket slightly, then pull it out from the server chassis.

Step 3 Align the expansion card with the guiding groove. Slide the expansion card into the slot until the

card firmly seats.

Step 4 Align the riser bracket to the system module (see the arrow direction mark 1), and push

it to locked position.

Step 5 Reverse Step 1 & 2 to lock the riser bracket firmly. Installation completed.

Step 1 Step 2

Step 3 Step 4

16

GS-SR157L Rack Mount Server

Step 3-6: Hard Disk Drive Installation

Step 1 Lossen the screws securing the hard drive plate.

Step 2 Slide toward to remove the hard drive plate from system.

Step 3 Place hard disk on the plate and lock hard drive with 4 screws.

Step 4 Replace the hard drive plate, slide the blank into the bay until it locks into place.Connect HDD

power cable.

Step 5 Reverse step 1, 2, 3 and 4 to complete the HDD installtion.

Step 1

Step 4

Step 2

Step 3

Remove

17

Hardware Installation Process

Step 3-7: FAN Duct Removal and Installation

Step 1 Pull up the screw-holder and lossen the thumbscrews. Lift up to remove the fan duct.

Step 2 For FAN Duct Installation, place the fan duct on the top of heat sinks. Fasten the screws to the

locked position and push down the screw-holders.

Step 1 Step 2

18

GS-SR157L Rack Mount Server

4-1: Front View of GS-SR157L

Chapter 4 Appearance of GS-SR157L









MOR-DCepyTmilS

ypoolFdradnatS

rotcennoCBSU

sDEL

)noitcerideRelosnoCroF(54JR

System Appearance

19

4-2: Rear View of GS-SR157L









 

rewoP

troPAGV

troPMOC

tolSresiReliforPwoL

tolSresiRhtgnel-lluF/ezis-lluF

rotcennoCdraobyeK

rotcennoC

esuoM

srotcennoCBSU

stroP2&1NAL

20

GS-SR157L Rack Mount Server

4-3: Switch and LED Indicators Introduction

Power/Sleep

NMI LAN1/2 Activities

HDD

Status HDD Fail Warning

ID

Name

Power

Status

HDD

LAN1

Activity

LAN2

Activity

Identification

Color Condition Description

Green On Power On

Green Blink Sleep (S1)

-- Off Power Off (S4/S5)

Green On System Ready On/ Alarm

Amber Blink System Ready but deqraded, CPU Failed,

DIMM Killed.

Amber On Critical Alarm: Critical Power Module Failure,

Critical FANs Failure, Voltage (Power Supply)

Critical Temperature and Voltage

-- Off System Not Ready/ Post error/NMI event/CPU

or terminator missing

Green Blink Hard Disk Drive Access

Amber On HDD Fault

-- Off No Access and No HDD Fault

Green On LAN Link / No access

Green Blink LAN access

-- Off Idle

Green On LAN Link / No access

Green Blink LAN access

-- Off Idle

Blue Blink Unit selected for identification

-- Off No identification

Page is loading ...

Gigabyte GS-SR157L Installation guide

This manual is also suitable for

Gigabyte GS-SR157L Installation guide

Related papers

Other documents