Gigabyte GS-ST590V System Installation Manual

System Installation Guide

GS-ST590V

5U RackMount /Tower Server

Dual Intel

®

Pentium Xeon

TM

(Nocona/Iwindale) Processor Serverboard

Rev. 1.0

25A080-05900-F00

2

GS-ST590V Rack Mount Server

Table of Content

Safety, Care and Regulatory Information................................................4

Introduction..............................................................................................8

Contents Packages ................................................................................8

WARNING!...............................................................................................8

Chapter 1 Features Summary.................................................................9

Chapter 2 System Overview................................................................. 11

Chapter 3 System Hardware Installation ...............................................12

Step 3-1: Chassis Removal and Installation ................................................................ 12

Step 3-2: CPU Installation............................................................................................... 13

Step 3-3: Heat Sink Installation....................................................................................... 14

Step 3-4: Memory Installation ........................................................................................ 14

Step 3-5: PCI Expansion Card Installation.................................................................... 15

Step 3-6: Hard Disk Drive Installation ............................................................................ 16

Chapter 4 Appearance of GS-ST590V..................................................17

4-1: Front View of GS-ST590V ...................................................................................... 17

4-2: Rear View of GS-ST590V ...................................................................................... 18

4-3: Switch and LED Indicators Introduction ................................................................. 19

4-4: LAN LED Description............................................................................................... 20

4-5 : Connector Icon Description ................................................................................... 21

Chapter 5 Motherboard Layout & Jumper Setting................................22

5-1: GA-9IVDT Motherboard Layout .............................................................................. 22

5-2: DDR DIMM Slot Population ..................................................................................... 24

5-3: Jumper Setting ......................................................................................................... 25

3

Table of Content

Chapter 6 BIOS Setup ..........................................................................28

Main...........................................................................................................30

Advanced ...................................................................................................33

PCI Configuration............................................................................................................. 34

Advanced Chipset Control ............................................................................................. 36

Advanced Processor Options ........................................................................................ 38

Peripheral Configuration .................................................................................................. 40

Hardware Monitor ............................................................................................................ 43

Security ......................................................................................................47

Server.........................................................................................................49

Console Redirection........................................................................................................ 49

Boot............................................................................................................53

Exit .............................................................................................................54

Chapter 7Driver Installation ...................................................................57

7-1: Intel Chipset Software Installation Utility................................................................ 57

7-2: Broadcom BCM5705/5721 Driver Installation....................................................... 59

7-3: Broadcom LAN Utility Software Installation .......................................................... 61

7-4: Adapetc 8130 Host Raid Driver Installation........................................................... 63

7-5: Adaptec Storage Manager Utility Installation......................................................... 64

7-6: DirectX 9.0C Driver Installation .............................................................................. 66

Chapter 8 Appendix..............................................................................67

8-1: Acronyms................................................................................................................. 67

4

GS-ST590V Rack Mount Server

Safety, Care and Regulatory Information

 Important safety information

Read and follow all instructions marked on the product and in the documentation before you operate

your system. Retain all safety and operating instructions for future use.

* The product should be operated only from the type of power source indicated on the rating label.

* If your computer has a voltage selector switch, make sure that the switch is in the proper position for

your area. The voltage selector switch is set at the factory to the correct voltage.

* The plug-socket combination must be accessible at all times because it serves as the main disconnect-

ing device.

* All product shipped with a three-wire electrical grounding-type plug only fits into a grounding-type power

outlet. This is a safety feature. The equipment grounding should be in accordance with local and national

electrical codes. The equipment operates safely when it is used in accordance with its marked electrical

ratings and product usage instructions

* Do not use this product near water or a heat source.

* Set up the product on a stable work surface or so as to ensure stability of the system.

* Openings in the case are provided for ventilation. Do not block or cover these openings. Make sure you

provide adequate space around the system for ventilation when you set up your work area. Never insert

objects of any kind into the ventilation openings.

* To avoid electrical shock, always unplug all power cables and modem cables from the wall outlets

before removing covers.

* Allow the product to cool before removing covers or touching internal components.

 Precaution for Product with Laser Devices

Observe the following precautions for laser devices:

* Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than

those specified in the product's documentation.

* Only authorized service technicians should repair laser devices.

 Precaution for Product with Modems, Telecommunications, ot Local Area

Network Options

Observe the following guidelines when working with options:

* Do not connect or use a modem or telephone during a lightning storm. There may be a risk of electrical

shock from lightning.

5

Safety Information

* To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

* Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

* Disconnect the modem cable before opening a product enclosure, touching or installing internal

components, or touching an uninsulated modem cable or jack.

* Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

 Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission

limits. Neither the provider nor the manufacturer are responsible for any radio or television interference

caused by using other than recommended cables and connectors or by unauthorized changes or

modifications to this equipment. Unauthorized changes or modifications could void the user's authority to

operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

 FCC part 68 (applicable to products fitted with USA modems)

The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among

other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment.

You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may

discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not

practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with

the FCC.

6

GS-ST590V Rack Mount Server

Your telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect proper operation of your equipment. If they do, you will be notified in advance to give you an

opportunity to maintain uninterrupted telephone service.

The FCC prohibits this equipment to be connected to party lines or coin-telephone service.

The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part

68, Sec. 68.381 (c) (3)).

/ for Canadian users only /

 Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus as set out in the radio interference regulations of Industry Canada.

Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux

appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edicte par

Industrie Canada.

 DOC notice (for products fitted with an Industry Canada-compliant modem)

The Canadian Department of Communications label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational and safety

requirements. The Department does not guarantee the equipment will operate to the user satisfaction.

Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the

local Telecommunications Company. The equipment must also be installed using an acceptable method

of connection. The customer should be aware that compliance with the above conditions might not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,

may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system, if resent are connected together. This precaution

may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

7

Safety Information

NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total

load to be connected to a telephone loop which is used by the device, to prevent overloading. The

termination on a loop may consist of any combination of devices subject only to the requirement that the

sum of the Load Numbers of all the devices does not exceed 100.

/ for European users only /

CAUTION

 Danger of explosion if battery is incorrectly

replaced.

 Replace only with the same or equivalent

type recommended by the manufacturer.

 Dispose of used batteries according to the

manufacturer’s instructions.

8

GS-ST590V Rack Mount Server

Introduction

Contents Packages

When opening the package, please ensure the system components are not damaged during the shipping.

Using the following checklist to verify the contents. If any component is missing or damaged in the

system, please contact your vendor immediately.

; Chassis ; Power Supply (Installed)

; The GA-9IVDT motherboard ; Silm Type CD-ROM drive (Installed)

; Silm type Floppy drive (Installed)

; Six Hadr Disk Drive Trays

; Two CPU Heat Sinks ; Driver CD for motherboard driver & utility

;

GS-ST590V System Installation Guide ; Tower Kits

Welcome to the Gigabyte GS-ST590V Rack mount / Tower Server System Installation Guide. The

guidebook provides instructions for configuration hardware for the GS-ST590V to your system.

This installation guide will assiste you in installing all the essential components for the sever system.

For your protection, please read and undertand all of the safety and operating instructions regarding your

Gigabyte Server and retain for future reference. The procedures in this guidebook assusme that your are

a system or network administrator experienced in installing similar hardware.

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

WARNING!

9

Feature Summary

Motherboard  GA-9IVDT

Processor Supported  Dual socket 604 for Intel

®

Xeon(Nocona/Iwindale)

processor suopprts 3.6 GB and upper

 Intel

®

Xeon (Nocona/Irwindale) CPUs supports 800 MHz FSB

 L2 cache depend on CPU

Chipset  Intel

®

E7320 Chipset

 Intel

®

6300ESB

System Memory:

Memory Capacity  6 x 240-pin DDRII DIMM up to 12 GB DRAM (Max)

Memory Type  Registered DDRII 400

DIMM Size  Support 128MB, 256MB, 512MB, and 1GB memory

Error Correction:  Single-bit Errors Correction, Multiple Bit Errors Detection

Expansion Slot  2 PCI-X slot support 64/66MHz (3.3V / The Green slot supports

ZCR)

 1 PCI slot supports 32/33MHz (5V)

 1 PCI-E slot by x4

SATA controller

Controller  Adaptec

®

AIC-8130 supports SATAII 4 ports

 Intel

®

6300ESB chipset (without RAID function)

Features  Supports Host RAID ( RAID 0,1)

 Mirroring supports automatic background rebuilds

 Supports RAID 0,1 5 10with ZCR card (2020s)Features LBA and

Extended Interrupt 13 drive translation in controller onboard BIOS

On-Board SATA RAID

Controller  Adaptec

®

AIC-8130 supports SATAII interface

Features  RAID 0,1,5,10 are supported when ZCR card is populated (Optional)

Cooling Fans:  1 X System Fan

 1 X Power Fan

Integrated LANs:

Controller  Broadcom

®

BCM 5705 and 5721 LAN Chipset

Integrated Graphics:

Controller  ATI Rage-XL

Graphics Memory  8Mb DDR SDRAM

Chapter 1 Features Summary

10

GS-ST590V Rack Mount Server

Mass Storage System  4 x Hot-Swap SATAII HDDs

 1 x Standard FDD

 1 Standard CD-ROM

Super I/O

Controller  ITE IT8712FIX

Built-in I/O  2 x Serial port (1 at front panel)

 4 x USB 2.0 dual-port connector (2 at front panel)

 1 x VGA connector

 2 x RJ45 LAN ports

 P/S 2 Keyboard and Mouse Connectors

System BIOS:

BIOS Type  Phoenix

®

BIOS, Multi-boot BBS 1.0 Compliant 8Mb Flash Memory

Special Features  BIOS HW Monitoring reporting (The values monitored by HW

Monitoring chipset)

 Console Redirection via COM ports

 Intel

®

Hyper Threading Support

 Resume after AC Back

 Wake On LAN

 ACPI 1.0 Compliant/ ACPI defined S1, S4, and S5

Server Management Functions: (Optional)

BMC Chip  NS IPMI 1.5 controller

Failure Detection  IPMI 1.5 specification of Server management

Event Logging  32KB Nonvolatile Memory to Log System Failure Events

Remote Management  Follow the IPMI 1.5 specification of Server management

Environment

Ambient Temperature  Operating Temperature: 5

o

C to 35

o

C

 Non-operating Temperature: 0

o

C to 50

o

C

Relative Humidity  10-80% operating Humidity at 30

o

C

Safety Regulations  FCC, CE, BSMI, CB, Win2000, 2003 WHQLIPMI 1.5 ( Option)

System Dimention:  8.5” x 17.0” x 19.1”

Electrical Power Supply  Single Power Supply 480W

If you are installing Windows

®

XP operating system, please

install Windows

®

XP service pack, otherwise system

may not run properly.

11

System Overview

Chapter 2 System Overview

I

A. Top Chassis Cover H. Blower Cover

B. Side Chassis Cover I. System Fan

C. Motehrboard - GA-9IVDT J. PCI Card Bracket

D. Hard Disk Drive Cage K. Rear Plate

E. ODD Dummy Cover L. FDD Supporter

F. FDD Dummy Cover M. FDD Cage

G. Front Bezel Door

B

A

C

D

E

G

F

H

J

K

L

M

12

GS-ST590V Rack Mount Server

Please observe the safety information in chapter “Important Safety Information”

Do not expose the server to extreme environmental conditions. Protect it from dust,

humidity, and heat.

Step 3-1: Chassis Removal and Installation

Step 1 Unlock the release button from the back of the server.

Step 2 Slide toward to remove the side cover.

Step 3 Reverse Step 1, and 2 to replace the chassis cover.

Chapter 3 System Hardware Installation

Step 1

Step 2

13

GS-ST590V Rack Mount Server

Step 1 Raise the locking bar on the socket.

Step 2 Aligning the pins of the processor with the socket, insert the processor into the socket.

Step 3 Close the handle completely and finish CPU installation.

Step 3-2: CPU Installation

Please make sure the CPU type and speed that are supported by the motherboard.

Step 1

Step 2

Step 3

Pin1 indicator

14

GS-ST590V Rack Mount Server

Step 3-3: Heat Sink Installation

Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well

remember to apply the thermal conductivity compound on the CPU.

Step 2 Lock the heat sink with the four screws. Installation completed.

Step 3-4: Memory Installation

1. The DIMM slot has a notch, so the DIMM memory module can only fit in one direction.

2. Insert the DIMM memory module vertically into the DIMM slot. Then push it down.

3. Close the plastic clip at both edges of theDIMM slots to lock the DIMM module.

4. DIMM must be populated in order starting at the farthest slot from the MCH chipset.

Each logical DIMM must be made of two identical DIMMs having the same device size on

each and the same DIMM size.

5. Reverse the installation steps when you wish to remove the DIMM module.

For detail DIMM Population, please refer to section 5-2: DDR DIMM Slot Population

Notch

Locked Retaining Clip

15

GS-ST590V Rack Mount Server

Step 3-5: PCI Expansion Card Installation

Step 1 Press the release button to remove the PCI bracket.

Step 2 Push the expansion board into the slot until the board firmly seats.

Repeat Step 1 & 2 to install remaining add-on cards.

Step 3 Reverse step 1 to complete installation.

Step 1

Release button

PCI bracket

Step 2

16

GS-ST590V Rack Mount Server

Step 3-6: Hard Disk Drive Installation

Step 1 Unlock the front bezel door.

Step 2 Open the front bezel by press down the indentation on the front bezel.

Step 3 Press the release button and pull the blank out of the drive bay.

Step 4 Slide hard disk into blank and secure it with screws.

Step 5 To replace the hard drive blank, slide the blank into the bay until it locks into place. Connect cable

and power.

Step 6 Place the hard disk into the server system.

Step 1

Step 2

Release button

Step 3

Step 4

17

GS-ST590V Rack Mount Server

4-1: Front View of GS-ST590V

Chapter 4 Appearance of GS-ST590V













11

1

11

nottuBrewoP

22

2

22

evirDyppolFdradnatS

33

3

33

stroPBSU

44

4

44

troPMOC

55

5

55

sDELtnorF

66

6

66

MOR-DCdradnatS

18

GS-ST590V Rack Mount Server

4-2: Rear View of GS-ST590V



















1

droCrewoP

2

hctiwSrewoP

3

esuoM

4

draobyeK

5

stroPBSU

6

troPMOC

7

troPAGV

8

troPNAL54JR

9

troPNAL54JR

19

GS-ST590V Rack Mount Server

4-3: Switch and LED Indicators Introduction

L1

L2

STS

HDD

PWR/SLP

NMI

RST

Name

PWR/SLP

STS

(System)

HDD

L1

Activity

L2

Activity

Color Condition Description

Green On Power On

Green & Amber Blink Sleep (S1)

Amber On Power Off (S4/S5)

Green On System healthy.

Amber On Critical Alarm: Critical Power Module Failure,

Critical FANs Failure, Voltage (Power Supply)

Critical Teemperature and Voltage

Green Blink Hard Disk Drive Access

Green On LAN Link / No access

Green Blink LAN access

-- Off LAN is idle

Green On LAN Link / No access

Green Blink LAN access

-- Off LAN is idle

20

GS-ST590V Rack Mount Server

4-4: LAN LED Description

Color Condition Description

Green ON LAN Link / no Access

Green BLINK LAN Access

Yellow ON 1Gbps connection

Green ON 100Mbps connection

- OFF 10Mbps connection

Name

LAN

Link/Activity

GbE LAN

Speed

Page is loading ...

Gigabyte GS-ST590V System Installation Manual

Gigabyte GS-ST590V System Installation Manual

Related papers

Other documents