Scanstrut PT2005 Installation guide

Brand
Scanstrut
Model
PT2005
Category
Network antennas
Type
Installation guide

Scanstrut PT2005 is a composite PowerTower designed for mounting antennas on boats. It comes with a base seal, nylon shouldered washers, and an IP67 cable grommet.

Here are some of its capabilities:

  • Can be attached to the boat using 8mm bolts, nuts, and washers (not included).
  • Can accommodate antennas with different hole configurations by drilling pilot holes and opening them out to the required diameter.
  • Can be used with cables up to Ø50mm in diameter, which are protected by the waterproof grommet.

Possible use cases:

  • Mounting VHF antennas for communication.
  • Mounting GPS antennas for navigation.

Scanstrut PT2005 is a composite PowerTower designed for mounting antennas on boats. It comes with a base seal, nylon shouldered washers, and an IP67 cable grommet.

Here are some of its capabilities:

  • Can be attached to the boat using 8mm bolts, nuts, and washers (not included).
  • Can accommodate antennas with different hole configurations by drilling pilot holes and opening them out to the required diameter.
  • Can be used with cables up to Ø50mm in diameter, which are protected by the waterproof grommet.

Possible use cases:

  • Mounting VHF antennas for communication.
  • Mounting GPS antennas for navigation.
Scanstrut Ltd. 1 Malt Mill, Totnes, Devon, UK TQ9 5NH Tel: +44(0)1803 863800 Fax: +44(0)1803 862223
e-mail: [email protected] website: www.scanstrut.com
Composite PowerTower Installation Instructions
PT2001 / PT2004 Page 2
PT2002 / PT2003 / PT2005 / PT2006 Page 3
www.busse-yachtshop.de | [email protected]
Scanstrut Ltd. 1 Malt Mill, Totnes, Devon, UK TQ9 5NH Tel: +44(0)1803 863800 Fax: +44(0)1803 862223
e-mail: [email protected] website: www.scanstrut.com
Composite PowerTower - PT2001/4
Installation Instructions
PowerTower kit contents
• PowerTower
• Base Seal
• 4 x Nylon Shouldered Washers
• IP67 Cable Grommet
Also Required:
• 4 x M8 Stainless Steel bolts, large washers and nuts to attach PowerTower to
deck/arch. Length to suit deck/arch thickness.
• Ø8.5mm Drill.
• Hole Cutter for cable loom; approx Ø50mm dia.
Drilling for the antenna.
1. Attach the PowerTower antenna template to the top of the top plate of
PowerTower. Mark through the centre of the holes for the antenna you are to mount.
IMPORTANT:
[A] Check that the doles shown on the drilling template match that of your
antenna.
2. Drill a pilot hole (about 2mm dia.) through the top of PowerTower.
3. Turn over PowerTower and, from the underneath of the top plate; open out the
holes to the required diameter.
Fitting PowerTower to the boat.
1. Attach PowerTower to the boat using 8mm (5/16 in) bolts, nuts and washers. Self-
locking or Nyloc nuts are recommended. Fit the white seal under the base of the
PowerTower.
2. Attach the antenna to the top of PowerTower using the bolts provided with the
antenna.
3. Install the cable using the waterproof grommet supplied. To fit the cable: Push
cable through hole in grommet to its chosen point and pull back until the internal
part of the grommet reverses back.
www.busse-yachtshop.de | [email protected]
Scanstrut Ltd. 1 Malt Mill, Totnes, Devon, UK TQ9 5NH Tel: +44(0)1803 863800 Fax: +44(0)1803 862223
e-mail: [email protected] website: www.scanstrut.com
Composite PowerTower - PT2002/3/5/6
Installation Instructions
PowerTower kit contents
• PowerTower
• Base Seal
• 4 x Nylon Shouldered Washers
• IP67 Cable Grommet
Also Required:
• 4 x M8 Stainless Steel bolts, large washers and nuts to attach PowerTower to
deck/arch. Length to suit deck/arch thickness.
• Ø8.5mm Drill.
• Hole Cutter for cable loom; approx Ø50mm dia.
Drilling for the antenna.
1. If installing PT2002/5, attach the PowerTower antenna template to the top of the
top plate of PowerTower. Mark through the centre of the holes for the antenna you
are to mount.
IMPORTANT:
[A] If you are installing a PT2003/6 please refer to the hole fixing
templates supplied with your antenna.
2. Drill a pilot hole (about 2mm dia.) through the top of PowerTower.
3. Turn over PowerTower and, from the underne ath of the top plate; open out the
holes to the required diameter.
Fitting PowerTower to the boat.
1. Attach PowerTower to the boat using 8mm (5/16 in) bolts, nuts and washers.
Self-locking or Nyloc nuts are recommended. Fit the white seal under the base of the
PowerTower.
2. Attach the antenna to the top of PowerTower using the bolts provided with the
antenna.
3. Install the cable using the waterproof grommet supplied. To fit the cable: Push
cable through hole in grommet to its chosen point and pull back until the internal
part of the grommet reverses back.
Note: PT2003, PT2006 ARE NOT SUPPLIED WITH GROMMETS. Mini M and Gyro GPS
antennas usually have cables coming out of the base and will enter the top of the
PowerTower seals or grommets for this are normally supplied by the antenna
manufacturer.
www.busse-yachtshop.de | [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3

Scanstrut PT2005 Installation guide

Brand
Scanstrut
Model
PT2005
Category
Network antennas
Type
Installation guide

Scanstrut PT2005 is a composite PowerTower designed for mounting antennas on boats. It comes with a base seal, nylon shouldered washers, and an IP67 cable grommet.

Here are some of its capabilities:

  • Can be attached to the boat using 8mm bolts, nuts, and washers (not included).
  • Can accommodate antennas with different hole configurations by drilling pilot holes and opening them out to the required diameter.
  • Can be used with cables up to Ø50mm in diameter, which are protected by the waterproof grommet.

Possible use cases:

  • Mounting VHF antennas for communication.
  • Mounting GPS antennas for navigation.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents