AMG AMG2902A Instruction Sheet

AMG
Brand
AMG
Model
AMG2902A
Type
Instruction Sheet

AMG AMG2902A is a standalone single-channel video-only fiber optic receiver for use on single-mode optical fiber. It is built to work with an AMG2901A or AMG2901AR Video Transmitter. The device receives a single video signal over a single-mode optical fiber. It features a 75-ohm BNC socket connector for video output, providing a 1 volt p-p nominal output level with a frequency response of 10Hz to 5.75MHz minimum. The optical connection utilizes FC/PC style connectors and supports a nominal wavelength of 1550nm with a sensitivity of -30dBm typical. The power supply requirement is +12 volts d.c.

AMG AMG2902A is a standalone single-channel video-only fiber optic receiver for use on single-mode optical fiber. It is built to work with an AMG2901A or AMG2901AR Video Transmitter. The device receives a single video signal over a single-mode optical fiber. It features a 75-ohm BNC socket connector for video output, providing a 1 volt p-p nominal output level with a frequency response of 10Hz to 5.75MHz minimum. The optical connection utilizes FC/PC style connectors and supports a nominal wavelength of 1550nm with a sensitivity of -30dBm typical. The power supply requirement is +12 volts d.c.

AMG Systems Ltd. reserve the right to make changes to this document without notice. The
information herein is believed to be accurate. No responsibility is assumed by AMG for its
use.
Page 1 of 2 AMG2902A
Instruction Sheet
D14613 00
AMG2902A
Instruction Sheet
AMG2902A Standalone Single Channel Video Only Fibre Optic Receiver for use on
Singlemode Optical Fibre
The AMG2902A receives a single video signal over a singlemode optical fibre. It is designed to
operate with an AMG2901A or an AMG2901AR Video Transmitter.
Video Output Connection
Connectors ........................... 75 ohm BNC Socket.
Output Impedance ................ 75 ohm terminated.
Output Level......................... 1 volt p-p nominal
Frequency Response............. 10Hz to 5.75MHz min.
Optical Connection
Connectors............................ FC/PC Style
Optical Sensitivity ................ -30dBm typ.
Wavelength........................... 1550nm nominal.
Power Connection
Power Supply ....................... +12 volts d.c. to +16 volts d.c. at 300mA
Connector ............................. Removable screw terminal connector (3.5mm)
See equipment label for connection details
A
MG
2902A
POWER IN
TX RX
VIDEO O O
FRONT PANEL INDICATORS
DATA-AUDIO
TX RX
CH1 O O
CH2 O O
CH3 O O
POWER
O
SINGLE MODE
VIDEO-DATA-AUDIO
TRANSCEIVER
IN+ 1
IN- 2
OUT+ 3
OUT- 4
IN+ 5
IN- 6
OUT+ 7
OUT- 8
IN+ 9
IN- 10
OUT+ 11
OUT- 12
GND
+12-16 Volts dc
VIDEO OUTPUT
OPTO IN OR
IN/OUT
OPTO OUT
VIDEO INPUT
218mm
109mm
193mm between mounting slot centres
AMG Systems Ltd. reserve the right to make changes to this document without notice. The
information herein is believed to be accurate. No responsibility is assumed by AMG for its
use.
Page 2 of 2 AMG2902A
Instruction Sheet
D14613 00
Data Connections
Not Used
Dimensions
Height ................................... 109mm
Width.................................... 218mm
Depth .................................... 39mm
Mounting Details
The AMG2902A is designed to mounted onto a panel via the two mounting slots of 4.5mm x
10mm.
Indicators
Power.................................... Green – unit powered
Off – no power applied to unit
Video RX.............................. Green – optical connection from AMG2901A OK and video
signal being received
Red/Green – optical connection from AMG2901A OK no video
Off – optical loss between AMG2902A and AMG2901A
too high
Safety
The 2900A series of products uses a Class 1 laser system in accordance with EN 60825-2:2000
and as such the optical power emitted from the optical connector is regarded as eye safe under all
operating conditions.
However it is always advisable to follow good practice when working with optical fibre systems.
This includes:
Do not stare with unprotected eyes or with any unapproved collimating device at fibre ends or
connector faces, or point them at other people.
Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with the optical fibres systems see
EN 60825-2:2000 or your local safety officer.
There are no user servicable parts within the AMG2902A.
In case of problem or failure contact your local support centre or AMG Systems Ltd, Technical
Support Department on tel. +44 (0) 1767 600777.
See unit data sheet for full specification.
  • Page 1 1
  • Page 2 2

AMG AMG2902A Instruction Sheet

AMG
Brand
AMG
Model
AMG2902A
Type
Instruction Sheet

AMG AMG2902A is a standalone single-channel video-only fiber optic receiver for use on single-mode optical fiber. It is built to work with an AMG2901A or AMG2901AR Video Transmitter. The device receives a single video signal over a single-mode optical fiber. It features a 75-ohm BNC socket connector for video output, providing a 1 volt p-p nominal output level with a frequency response of 10Hz to 5.75MHz minimum. The optical connection utilizes FC/PC style connectors and supports a nominal wavelength of 1550nm with a sensitivity of -30dBm typical. The power supply requirement is +12 volts d.c.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers