2. Beghelli
  3. SCALA

Beghelli SCALA Installation guide

  • Hello! I've reviewed the provided installation instructions for the Beghelli SCALA Stairwell LED fixtures. This document covers important safety precautions, step-by-step installation procedures, and describes mounting options, wiring, and diffuser installation. I'm ready to answer any questions you have about these 30W and 40W stairwell LED models.
  • What should I do first before installing?
    What should I do with unused wires?
    What is needed to complete diffuser installation?
INSTALLATION INSTRUCTION
SCALA
012615EC
Beghelli USA
3250 Corporate Way
Miramar, Florida 33025 USA
P: 800 726 4316 / P: 954 442 6600
F: 954 442 6677
www.BeghelliUSA.com
Beghelli Canada
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
P: (905) 948-9500
F: (905) 948-8673
www.BeghelliCanada.com
Beghelli Mexico
Av El Marques No. 70, Interior 4
76246 Mpio. El Marquez
Queretano, QRO. Mexico
P: +52 442-221-6439 / F: +52 442-221-6215
www.BeghelliMexico.com
STAIRWELL LED
2www.beghelliusa.com
SCALA
STAIRWELL LED
30W & 40W MODELS
120V-277V INPUT
AC & EM, 2FT
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. Do not let power cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to
tampering.
4. The use of accessory equipment not recommended by Beghelli Inc., may cause an unsafe condition, and will void
the warranty.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
SAVE THESE INSTRUCTIONS!
First make sure power is turned off!
1. Remove diffuser lens.
2. Carefully remove the LED reflector from housing. You’ll find the mounting hardware bag needed for step 9.
3. Extract mounting hardware. Install conduit fitting.
4. Prepare fixture for wiring / hang reflector from internal clips. Connect AC supply and ground as labeled on the
provided wire leads. CAP unused wires!
CAUTION! Failure to insulate unused wire may result in a shock hazard or unsafe condition as well as equipment
failure. Route wires and secure them in place.
5. Install diffuser clips.
6. Install sensor’s gasket and diffuser.
7. Secure diffuser with clips. Reposition the diffuser/lens and snap each of the four (4) clips into place (a “clack” sound is
made).
8. Remove protective film from sesnor.
9. Secure sensor with locknut and install sensor’s lens.
10. Turn on AC.
SAVE THESE INSTRUCTIONS! No user serviceable parts. Refer service to a qualified service
technician. Read instructions prior to installing and/or operating
this device. Installation should be performed by a licensed
electrician/installer in accordance with local codes.
INSTALLATION INSTRUCTION
LED | WET | 2FT | BAA
3
www.beghelliusa.com
TYPICAL INSTALLATION
SCALA
1. REMOVE DIFFUSER / LENS 2. REMOVE LED REFLECTOR FROM HOUSING
BE CAREFUL TO NOT TOUCH THE LEDs!
3. EXTRACT MOUNTING HARDWARE,
INSTALL CONDUIT FITTING
4. CONNECT TO POWER
5. INSTALL DIFFUSER CLIPS 6. INSTALL SENSOR’S GASKET & DIFFUSER
N
L
Connect cables from
MAIN AC inside unit
G
4www.beghelliusa.com
TYPICAL INSTALLATION
SCALA
7. SECURE DIFFUSER WITH CLIPS 8. REMOVE PROTECTIVE FILM FROM SENSOR
9. SECURE SENSOR WITH LOCK NUT. INSTALL SENSOR’S LENS.
5
www.beghelliusa.com
SCALA MOUNTING
6www.beghelliusa.com
MOUNTING
MOUNTING
SCALA
7
www.beghelliusa.com
MOUNTING
MOUNTING
SCALA
120-277VAC
L
G
N
1/2” IP STEM
1/2” IP LOCKNUT
CONNECT POWER IN ACCORDANCE
WITH ALL CODES AND LABLES
J-BOX PROVIDED AND INSTALLED BY OTHERS
INSTALL CROSS BAR WITH
SCREWS FROM THE J-BOX
(2) SCREWS IN J-BOX (BY OTHERS)
CANOPY
SET SCREW FOR SLIP RING
SLIP RING (TO POSITION CANOPY)
LOCK NUT (FOR DOUBLE LOCK ON STEM)
SINGLE PENDANT
/