Lumantek VENTUS F1 User's Operation Manual

LUMANTEK Co., Ltd http://www.lumantek.com

Head Oce : # 1208, Woolim Lion’s Valley II, 680 Gasan-Dong, Geuncheon-Gu, SEOUL, KOREA (150-803)

TEL : +82-2-2027-2400 / FAX: +82-2-2027-2409 / e-Mail : [email protected]

USER OPERATION MANUAL

[Stand Alone Type Modulator] >>First Edition

DAB / DAB+ DTMB

AWGN

VENTUS F1

VENTUS F1 ™

Trademarks and Copyright

Copyright:

Tel: +82 2 2027 2400, Fax: +82 2 2027 2409.

duced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording or other-

wise, without prior written permission of LUMANTEK.

LUMANTEK Co., Ltd. are registered in the United States and other countries. The LUMANTEK word and design mark, VIA, Vis-

ibility.Insight.Answers, Amico ™, Lumantek Logo, Mega Cruiser ™, ORIX ™, X-Cruiser ™, DTA-Plus ™, Media Blaster ™, and

VENTUS F1 are all trademarks of LUMANTEK Co., Ltd. All other trademarks or service marks are the property of their respective holders

and are hereby acknowledged.

Software and documentation are owned by LUMANTEK and are protected by United States copyright laws other applicable copyright laws

and international treaty provisions. LUMANTEK and its suppliers retain all rights not expressly granted.

Disclaimers:

The information in this document is furnished for informational purposes only, is subject to change without prior notice, and should not be

construed as a commitment by LUMANTEK.

Although great care has been taken in the production of this program to ensure accuracy, LUMANTEK cannot under any circumstances

accept responsibility for errors, omissions or advice given in this manual.

Contact Us:

LUMANTEK is leading provider of platforms for Digital TV and Mobile TV services. We are committed to maintaining a high level of

quality in all our documentation. Towards this effort, we welcome your comments and suggestions regarding the content and structure of

this document. Please fax or mail your comments and suggestions to the attention of:

LUMANTEK Attn: Product Support Department Unit 1208, Woolim Lion’s Valley II, 680 Gasan-Dong, Gumcheon Gu, Seoul Korea (153-

830), +82 2 2027 2400, Fax: +82 2 2027 2409

Environmental Issues:

Thank you for buying a product which contributes to a reduction in pollution and thereby helps save the environment. Our products reduce

the need for travel and transport and thereby reduce pollution. Our products have either no or few consumable parts (chemicals, toner, gas,

paper). Our products are low energy consuming products.

Waste handling:

There is need to send material back to LUMANTEK. Please contact your local dealer for information on recycling the product by sending

the main parts of the product for disassembly at local electronic waste stations.

Production of products:

Our factories employ the most efcient environmental methods for reducing waste and pollution by ensuring that the products are recy-

clable.

Service Policy Warrenty:

Lumantek limited one year warranty. All equipment sold, will have a standard 1 year warrenty. If you should have any problems and have

determined our equipment defective, please contact us via FAX, Phone or E-Mail so we may determine the best way to service you.

- Phone # : 82 - 2 - 2027 - 2400

- FAX # : 82 - 2 - 2027 - 2409

- E-Mail : [email protected]

1. INTRODUCTION

1.1 VENTUS F1 System overview

VENTUS F1™ is a product that broke away from the existing measurement system. It can be

used without the PC or Notebook. It is suitable for mass production and the signal room.

It is a portable measurement system unlike the existing Signal Generator. It can be used for

many purposes such as development, product demonstration, marketing, and domestic and

overseas business trip purposes.

Basically, it consists of Embedded PC (SSD HDD built in), ASI-INPUT, ASI-OUTPUT port, RF

Modulator, and RF Upconverter. If the user wants, any DTV SD format in the world can be

used. DTV SD formats supported by VENUS F1 are as follows.

DVB-T/H, DVB-C (A,C), ATSC(8VSB), OpenCable, ISDB-T/Tb, T-DMB

ISDB-T/SBTV

Picture 1. VENTUS Supporting Spec

1.2 VENTUS Development Concept

VENTUS F1 solution can be used to test all DTV SD formats in the world. It is a All-in-One type

measurement solution. As it is a portable product, it has maximized user convenience.

Laptop

Computer

RF OUT

Upcoverter

Attenuator

VENTUS Application

ASI OUT

ASI IN

VENTUS

Desktop

Computer TDMB/DAB+

Picture 2. VENTUS Development Concept

DTMB

All in One type

1.3 VENTUS F1 Basic Organization

VENTUS device is possible to transmit DTV Skill Standard by RF through USB Interface between

VENTUS and PC or Notebook.

Picture 3. VENTUS F1 Basic Organization

Main Feature

All the system can be control from LCD panel.•

Embedded System Built in.•

-> Basic Hard Disk Built in (SSD Type 32 GB)

External USB Disk and Memory can be used •

Through the monitor port, the same UI (T-PUMP) is available•

VENTUS F1 support DTV and Mobile TV Standard Support•

TDMB/DAB+

DTMB

1.4 VENTUS Basic Organization

VENTUS device is possible to transmit DTV Skill Standard by RF through USB Interface between

VENTUS and PC or Notebook.

Picture 4. VENTUS F1 Basic Organization

2. PRODUCT DESCRIPTION

2-1. Front View

Picture 6 VENTUS F1 Front and Rear Dimension

2-2. Rear View

Picture 7 VENTUS F1

22. FEATURE DESCRIPTION

221. FORNT VIEW

RF OUTPUT Port: RF Output port•

RF On/OFF button•

Play/Stop button•

LCD Window•

Enter, ESC Button•

Arrow button : To change the menu and set the value•

Reset /Power button•

222. REAR VIEW

POWER SW: Power Switch•

POWER Port•

Embedded PC Port : an external input built-in PC interface, •

 VGA Port : Used to connect an external monitor

 USB Port : Used to connect an external monitor

 Ethernet Port : When using Network connection (FTP)

ASI-OUT, ASI-IN Built in•

23. VENTUS F1 PACKAGE CONTENTS

VENTUS F1

Accessories

AC Power Cord USB Cable: A-B type USB Flash Memory

- VENTUS F1 Driver

(Inserted T-pump Software)

User’s Guide/

Warranty Card

3. SYSTEM OPERATING

3-1. VENTUS Hardware Install

Embedded PC is built in VENTUS F1. It is not necessory to install software.

]

Picture 8 VENTUS F1

3-2. VENTUS F1 Operation Procedure

VENTUS F1 products with the following order: Detail setting are available on LCD window.

The above operating is a Procedure after selecting Modulation Type.

VENTUS FEATURE

Picture 9 VENTUS F1

Power Button : VENTUS F1 Power on -> system Booting

Reset Button : Forced the Power o

Enter Button : VENTUS F1 Conguration Setting

ESC Button

PLAY / STOP Button : When completing setting, use PLAY/ STOP Button

- To change the Modulation, it is neccessory to end by using STOP button

RF On/O : Monitoring transmission and forced the Power o

SELECTING CW MODE

1. To use CW mode, press #5 Modulator on Menu.

2. When you select a menu, CW Modulator Please Wait for the notication to display text set-

tings complete text disappears

3. On the Settings menu, select the Parameter button, you will select the following menu.

4. Once set up the initial menu, the ESC button and select the Play button will be bailed out.

SELECTING RF OUTPUT : DVBT

1. To use DVB-T mode, the LCD Main Menu, select #5 Modulator.

2. DVB-T option is separated in (2,8 K) menu, and (4K) menu.

3. After setting DVB- T/H in Modulator selection, Select the Settings menu #6 to click Param-

eter.

- To set Parameter value, please use cursor key to change details parameters value.

Items Value

Code Rate 1/2, 2/3, 3/4, 5/6, 7/8

Const. Type QPSK, 16 QAM, 64 QAM

IFFT 2K, 8K, 4k

Bandwidth 5, 6, 7, 8 MHz

Guard Interval 1/32, 1/16, 1/8, 1/4

Once set up, the ESC button will take out to the previous menu.

4. When Parameter settings has been completed, Click # 4 from Menu to select transmitting

stream.

- It is available to open Species the stream from the built-in SSD hard disk or external USB

disk. Select your stream by using the ENTER button.

5. Once you select a stream by using ESC button to go to the previous menu, the frequency and

level setting. First, the frequency settings are as follows.

After clicking the #1 from menu, the Frequency menu will display. Set the desired frequency

using the cursor keys.

Use up and down cursor keys to change the frequency, left and right cursor keys to move the

unit.

Once set up the frequency, go to the previous menu by clicking ESC button

6. Once set up specify the frequency for power transmission from the Settings menu, select

# 2 from Menu.

-> Set desired transmission power level by using the cursor keys

- Use UP/Down Cursor Key to Change the Level, and use Left/ Right Cursor Key to

Change the unit.

7. When completing setting, the DVB-T is ready for transmission.

Press the ESC button to exit to initial menu. Use PLAY button to play.

If you need to save the settings, go to the Settings menu. to click the Project menu.

Then select # 9 from the Store menu. Choose from slot -1 to slot 10 to save.

When ones need to open saved le, click [Recall] menu and select slot 1 ~ slot 10.

SELECTING RF OUTPUT : DVBC

1. To use DVB-C mode, the LCD Main Menu, select #5 Modulator.

- DVB-C Modulator of the following options are selected by the ENTER button.

- When is not Multi option, it will only show the available option.

2. After setting DVB- C in Modulator selection, Select the Settings menu #6 to click Parameter.

- To set Parameter value, please use cursor key to change details parameters value.

Items Value

Const. Type QPSK, 16 QAM, 64 QAM

- Once set up, the ESC button will take out to the previous menu.

3. When Parameter settings has been completed, Click # 4 from Menu to select transmitting

stream.

- It is available to open Species the stream from the built-in SSD hard disk or external USB

disk. Select your stream by using the ENTER button.

4. Once you select a stream by using ESC button to go to the previous menu, the frequency

and level setting. First, the frequency settings are as follows.

After clicking the #1 from menu, the Frequency menu will display. Set the desired frequency

using the cursor keys.

Use up and down cursor keys to change the frequency, left and right cursor keys to move the

unit.

Once set up the frequency, go to the previous menu by clicking ESC button

5. Once set up specify the frequency for power transmission from the Settings menu, select

# 2 from Menu.

-> Set desired transmission power level by using the cursor keys

- Use UP/Down Cursor Key to Change the Level, and use Left/ Right Cursor Key to

Change the unit.

6. When completing setting, the DVB-C is ready for transmission.

Press the ESC button to exit to initial menu. Use PLAY button to play.

If you need to save the settings, go to the Settings menu. to click the Project menu.

Then select # 9 from the Store menu. Choose from slot -1 to slot 10 to save.

When ones need to open saved le, click [Recall] menu and select slot 1 ~ slot 10.

SELECTING RF OUTPUT : ATSC

1. To use ATSC mode, the LCD Main Menu, select #5 Modulator

- Sselect ATSC by clicking ENTER button.

- When is not Multi option, it will only show the available option.

2. After setting DVB- C in Modulator selection, Select the Settings menu #6 to click Parameter.

- INPUT Type : SSD ( Embedded PC Harddisk build-in)

- Once set up, the ESC button will take out to the previous menu.

3. When Parameter settings has been completed, Click # 4 from Menu to select transmitting

stream.

It is available to open Species the stream from the built-in SSD hard disk or external USB

disk. Select your stream by using the ENTER button.

4. Once you select a stream by using ESC button to go to the previous menu, the frequency

and level setting. First, the frequency settings are as follows.

After clicking the #1 from menu, the Frequency menu will display. Set the desired frequency

using the cursor keys.

Use up and down cursor keys to change the frequency, left and right cursor keys to move the

unit.

Once set up the frequency, go to the previous menu by clicking ESC button

5. Once set up specify the frequency for power transmission from the Settings menu, select

# 2 from Menu.

-> Set desired transmission power level by using the cursor keys

- Use UP/Down Cursor Key to Change the Level, and use Left/ Right Cursor Key to

Change the unit.

6. When completing setting, the ATSC is ready for transmission.

Press the ESC button to exit to initial menu. Use PLAY button to play.

If you need to save the settings, go to the Settings menu. to click the Project menu.

Then select # 9 from the Store menu. Choose from slot -1 to slot 10 to save.

When ones need to open saved le, click [Recall] menu and select slot 1 ~ slot 10.

SELECTING RF OUTPUT : OPENCABLE

1. To use OpenCable mode, the LCD Main Menu, select #5 Modulator

- Sselect Open-Cable by clicking ENTER button.

- When is not Multi option, it will only show the available option.

2. After setting OpenCable in Modulator selection, Select the Settings menu #6 to click Param-

eter.

- INPUT Type : SSD ( Embedded PC Harddisk build-in)

- Once set up, the ESC button will take out to the previous menu.

click to select transmitting stream.

Items Value

Const. Type 64QAM, 256 QAM

CW/I/J

I=128 J=1

I=128 J=2

I=64 J=2

I=128 J=3

I=32 J=4

I=128 J=4

I=16 J=8

I=128 J=5

I=8 J=16

I=128 J=6

I=128 J=7

I=128 J=8

ESC button will take out to the previous menu.

E

Page is loading ...

Lumantek VENTUS F1 User's Operation Manual

Lumantek VENTUS F1 User's Operation Manual

Other documents