1
Package Contents
PC-2111-G2/2111E-G2 POS Terminal………………………….…x1
Power Cord……………………………………………………..…..x1
Power Adapter….…......................................................................…x1
User manual..………..……………………………………………...x1
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement résidentiel, cet
équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the
authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise. The
manufacturer is by no means responsible for any damage or hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne autre que
les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le problème qui se produit.
La garantie s'annule si l'utilisateur ne suit pas les instructions d'application de cette marchandise.
Le fabricant n'est en aucun cas responsable de tout dommage ou danger causé par une mauvaise
application.
PC-2111-G2/2111E-G2
POS Terminal
User Manual
11180903010 Ver. A0
http://www.posiflex.com
2
警告使用者
為避免電磁干擾，本產品不應安裝或使用於住宅環境。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be present.
CONSIGNES DE SÉ CURITÉ
Ne jamais ouvrir l'équipement. Pour des raisons de sécurité, l'équipement doit être ouvert et
installé uniquement par une personne qualifiée. La prise de courant doit être située à proximité de
l'équipement et doit être facilement accessible. Cet équipement ne convient pas à une utilisation
dans des endroits où des enfants sont susceptibles d'être presents.
WARNING
Power cord shall be connected to a socket-outlet with earthing connection.
ATTENTION
Le cordon d'alimentation doit être connecté à une prise de courant avec mise à la terre.
BATTERY WARNING
Risk of explosion if battery is replaced by an incorrect type. Dispose of expended battery in
accordance with local disposal regulations.
AVERTISSEMENT DE BATTERIE
Risque d'explosion si la batterie est remplacée par un type incorrect. Jetez la batterie usagée
conformément aux réglementations locales en matière d'élimination.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。
3
Overview
PC-2111-G2
Front View
Rear View
10.1” PCAP
Touch Panel
Camera (Optional)
Attachment Cover
Power Button
Power Status LED
Indicator
VESA 75 x 75
Mounting Holes
4
PC-2111E-G2
Front View
Rear View
10.1” PCAP
Touch Panel
Attachment
Cover
Base Stand
Camera (Optional)
Cable Exit
Power Button
Power Status LED
Indicator
5
Rear I/O Ports
PC-2111-G2
PC-2111E-G2
Connecting Power Adapter and I/O Cables
To have the terminal ready for operation, please connect the connector of
power adapter and all of the connectors of required I/O cables respectively to
the 12VDC-IN power jack and appropriate I/O ports. Please make sure that
each of the cables is fully connected to the correct port. Damages due to
incorrect connection or orientation are not covered by product warranty!
Some cable connectors like the connectors of LAN cables have to be gently
inserted until a click is heard. And please make sure that each connector has to
be connected to the right peripheral device in the right way.
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty.
USB 3.0 Ports
LAN Port
12V DC-IN Power Jack
CR Port
Serial RJ50 Port
Mini-HDMI Port
LAN Port
12V DC-IN Power Jack
USB 3.0 Ports
6
The means of power cord should be connected to a socket-outlet with
earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
Powering ON/OFF the POS Terminal
Power ON the POS Terminal
Press down the power button to power on the POS
terminal.
Power OFF the POS Terminal
In most cases, push the power button again to power the
system off. However, if the POS box halts for unknown
reasons, please be advised to hold the power more than
10 seconds to initiate a forced shutdown.
Status LED Indicator
There is a power status LED indicator on the left side of the PC-2111-
G2/2111E-G2. After powering ON the POS system, you can read the system
operation status from the power status LED indicators. The LED status is
described below.
LED
Status
Description
POWER
Blue
System power ON
Orange
System standby
Installing Optional Peripheral Devices
PC-2111-G2/2111E-G2 can work with multiple optional upgrade kits, such as
MSR, Smart Card Reader and the like. For the detailed instructions, refer to
the user manual related to each peripheral devices. Before installing an
optional peripheral device, make sure that the system is powered off to prevent
electric hazard! Failure to follow the warning description will void the product
warranty!
Installing an Operating System
This product is highly professional equipment. Therefore, we do NOT
encourage you to install any operating system into this machine without
professional assistance. Posiflex Technology, Inc. shall not be responsible for
any technical support to questions on this aspect. We
7
suggest that you contact your dealer for OS installation.
Operating System Recovery
For the PC-2111-G2/2111E-G2 main system preloaded with an operating
system, Posiflex provides a recovery DVD shipped with the main system for
the preloaded operating system. The system integrator shall take care of
software restoration after the OS is recovered.
If you plan to recover your operating system, we do NOT encourage you to
recover any operating system. Please contact your service center for operating
system recovery.
Installing Drivers
Please visit Posiflex official website to download and install the related drivers.
http://www.posiflex.com/en-global/Download/download)
Specifications
PC-2111-G2
PC-2111E-G2
System
CPU
Intel Elkhart Lake Celeron J6412
Memory
1 x DDR4 SO-DIMM socket, 16GB max.
vPro
N/A
TPM
Yes
Power Source
12V/40W
12V/60W
Camera
Optional 1MP camera module
Storage
Storage
1 x M.2 port (M.2 2280 / B+M key)
OS Support
OS
Windows 10 IoT / Windows 11 IoT GAC
Display & Monitor
LCD Panel
10.1” 1280 x 800 TFT LCD
Touch Panel
P-CAP touch with multi-touch support
Outside I/O Ports
Display Port
N/A
1 x mini-HDMI
Serial Port
N/A
1 x RJ-50
Ethernet Port
1 x 10/100/1000 Mb
8
PC-2111-G2
PC-2111E-G2
Standard USB Port
4 x USB 3.0
Audio Port
1 x internal speaker
CR Port
N/A
1 x CR port, controlling
2 x CR
LED Indicator
1 x bi-color LED
Power
1 x 2-pin power phone jack
Expansion
Expansion Slot
1 x M.2 2230 for WiFi/BT module
Mechanical
Mechanical
Without base stand
With base stand
Dimension
259.0 x 173.4 x 36.5 (without base stand,
W x H x D in mm)
Weight
1.01 Kg
1.96 Kg
Environmental
Operating Condition
0°C - 40°C, 20%RH - 90%RH
Storage Condition
-20°C - 60°C, 10%RH - 90%RH
Outline Dimension
PC-2111-G2
9
PC-2111E-G2
11
<MEMO>
12
<MEMO>
/
