QVIS APOIR-PTZ23 User manual

APOIR-PTZ23

23X ZOOM ANALOGUE PTZ CAMERA

User’s Manual

V1.0 11 / 2013

Table of Contents

1 FEATURES AND FUNCTIONS ................................................................................................ 1

1.1 General Introduction .......................................................................................................................................... 1

1.2 Features .............................................................................................................................................................. 1

1.2.1 On-Screen Menu ............................................................................................................................................. 1

1.2.2 On-screen Tips ................................................................................................................................................ 1

1.2.3 Support multiple protocols ............................................................................................................................... 1

1.2.4 Proportional Pan and Tilt ................................................................................................................................. 1

1.2.5 Preset Setup and Call ...................................................................................................................................... 2

1.2.6 Auto Scan ........................................................................................................................................................ 2

1.2.7 Auto Touring .................................................................................................................................................... 2

1.2.8 Auto Pattern ..................................................................................................................................................... 2

1.2.9 Privacy Masking ............................................................................................................................................... 2

1.2.10 IR Night Vision ............................................................................................................................................. 2

1.2.11 Action on Alarm ........................................................................................................................................... 2

1.2.12 Auto Flip ...................................................................................................................................................... 2

1.2.13 Self-diagnosis .............................................................................................................................................. 2

1.2.14 Day/Night Mode (B/W & Color Mode) ......................................................................................................... 3

1.2.15 Auto Focus .................................................................................................................................................. 3

1.2.16 Backlight Compensation .............................................................................................................................. 3

1.2.17 Pan Tilt and Zoom ....................................................................................................................................... 3

1.2.18 3D Intelligent Location ................................................................................................................................. 3

1.2.19 Idle Status .................................................................................................................................................... 3

1.2.20 Image Stabilizer/Flip .................................................................................................................................... 3

2 IR PTZ CAMERA INSTALLATION .......................................................................................... 4

2.1 Installation Preparation ..................................................................................................................................... 4

2.2 IR PTZ camera and network IR PTZ camera installation ................................................................................ 5

2.2.1 PTZ camera bracket installation ...................................................................................................................... 5

2.2.2 Pipe thread bracket installation ........................................................................................................................ 5

2.2.3 Clip wall mount bracket installation.................................................................................................................. 6

2.2.4 Secure the PTZ camera to the flange .............................................................................................................. 6

3 BRACKET DIMENSIONS ......................................................................................................... 8

3.1 Wall mount bracket ............................................................................................................................................ 8

3.2 Hanging mount bracket (Multiple Lengths) ..................................................................................................... 8

3.3 Corner mount bracket ........................................................................................................................................ 9

3.4 Pole mount bracket ............................................................................................................................................ 9

4 WALL MOUNT BRACKET INSTALLATION .......................................................................... 10

4.1 Component Installation ................................................................................................................................... 10

4.2 Installation ........................................................................................................................................................ 10

4.2.1 Installation Requirements .............................................................................................................................. 10

4.2.2 Installation Steps ........................................................................................................................................... 10

5 HANG MOUNT BRACKET INSTALLATION ......................................................................... 12

5.1 Component Installation ................................................................................................................................... 12

5.2 Installation ........................................................................................................................................................ 12

5.2.1 Installation Requirements .............................................................................................................................. 12

5.2.2 Installation Steps ........................................................................................................................................... 12

6 CORNER MOUNT BRACKET INSTALLATION .................................................................... 14

6.1 Component Installation ................................................................................................................................... 14

6.2 Installation ........................................................................................................................................................ 14

6.2.1 Installation Requirements .............................................................................................................................. 14

6.2.2 Installation Steps ........................................................................................................................................... 14

7 POLE MOUNT BRACKET INSTALLATION .......................................................................... 16

7.1 Installation ........................................................................................................................................................ 16

7.1.1 Installation Requirements .............................................................................................................................. 16

8 PROTOCOL, BAUD RATE, ADDRESS SETUP .................................................................... 18

8.1 Protocol and Baud Rate Setup ....................................................................................................................... 18

8.2 Set address dial switch ................................................................................................................................... 20

9 CABLE CONNECTION .......................................................................................................... 21

9.1 Power board Cable Connection ...................................................................................................................... 21

9.2 System Layout .................................................................................................................................................. 22

9.2.1 BUS connection ............................................................................................................................................. 22

9.2.2 Alarm Connection .......................................................................................................................................... 23

9.2.3 Keyboard Connection .................................................................................................................................... 24

10 MENU ................................................................................................................................. 25

10.1 Screen Menu Index .......................................................................................................................................... 25

10.2 Self-diagnosis System Information ................................................................................................................ 26

10.3 Main Menu ......................................................................................................................................................... 26

10.4 Menu Operation ................................................................................................................................................ 27

10.4.1 System Information.................................................................................................................................... 27

10.4.2 Display Setting ........................................................................................................................................... 29

10.4.3 Camera Setting .......................................................................................................................................... 29

10.4.4 Function Setting ......................................................................................................................................... 34

10.4.5 IR Light Setup ............................................................................................................................................ 43

10.4.6 Alarm Setup ............................................................................................................................................... 44

10.5 Abnormal Phenomenon Operation ................................................................................................................ 44

10.5.1 Restore to Factory Default Setup .............................................................................................................. 44

10.5.2 Irregular PTZ Movement ........................................................................................................................... 44

11 CABLE CONNECTION ...................................................................................................... 45

11.1 Combination Cable Connection...................................................................................................................... 45

12 FAQ .................................................................................................................................... 46

12.1 Daily Maintenance ............................................................................................................................................ 46

12.2 Problems and Solutions .................................................................................................................................. 46

Welcome

Thank you for purchasing the APOIR-23PTZ camera.

This user’s manual is designed to be a reference tool for the installation and

operation of your system.

Here you can find information about the corresponding camera’s features and

functions, as well as a detailed installation method.

Before installation and operation please read the following safeguards and

warnings carefully!

Important Safeguards and Warnings

1．Electrical safety

 All installation and operation here should conform to your local electrical safety codes.

 We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or

installation.

 We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation Security

 No heavy stress, violent vibration or contact with water is allowed during transportation, storage and

installation.

 Please use the original packing material (or the material of the same quality) when you ship it back to the

manufacturer.

3．Installation

 Do not apply power to the product before completing installation.

 Do not put object(s) on the product.

4．Environment

 This product should be installed in a cool, dry place away from direct sunlight, inflammable, explosive

substances and etc.

 Please keep it away from environments that contain electromagnetic radiation or objects that produce it.

 Please keep sound ventilation around the device at all times.

 Do not allow the water and other liquid to penetrate into the device if casing has been compromised. This

series product complies with the IP66 standard specified in the Degrees of Protection Provided by

Enclosure.

 Please make sure the CCD (CMOS) component is away from the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

5. Daily Maintenance

 Current series product has no power button. Please unplug all corresponding power cables before your

begin installation or daily maintenance work.

 Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a long

time.

 Do not touch CCD (CMOS) component. You can use the blower to clean the dust on the surface of the

device. You can use the dry cloth with some alcohol or mild detergent to clear if necessary.

 Do not use volatility solvent such as the benzene or thinner, or detergent with strong abradability. It may

result in lens damage or it may adversely affect the device performance.

 If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the

device. Finally use the dry cloth to clean the device.

6. About Accessories

Always use all the accessories recommended by manufacturer.

Before installation, please open the package and check that all the components are included in the package.

Contact your local retailer ASAP if something is missing in your package.

1 Features and Functions

1.1 General Introduction

The IR intelligent PTZ dome analogue camera not only gives you 23X optical zoom but also the ability to digitally

zoom in to the video footage up to 16X, to scrutinise far away objects much more closely. It adopts a new

configuration design and is easy to install during project construction. This is a digitally intelligent product that

can provide you with vivid video visuals.

The camera’s external ports adopt a buckle design and a waterproof interface incorporated to the pipe thread

allowing for a quick & easy installation process. It supports various languages, a real-time clock function,

automatic protocol recognition, 360° continuous pan, 92°tilt and 180° auto flip (with blind spot monitor).

Through detailed design towards the camera’s aesthetics it also allows it to be incorporated into many modern

settings. At the same the shape and materials provides it with the robustness to survive a variety of weather

conditions. Internal technology allows for the PTZ rotation speed to be automatically adjusted according to lens

zoom speed. It supports various languages, real-time clock function, blind spot recognition and protocol auto

recognition. It also gives you a full 360° continuously pan, 92°tilt and 180° auto flip.

1.2 Features

This PTZ PTZ camera has the following features:

1.2.1 On-Screen Menu

 There are multiple language options for the menu system to be displayed in preferred language.

 It is easy for you to view dome information and to configure the dome camera parameters.

1.2.2 On-screen Tips

Here you can view:

 Preset name and system version (software and hardware)

 Dome system temperature (this is optional, you can disable this function)

 Dome address (optional, you can disable this function)

1.2.3 Support multiple protocols

Supports universally used protocols such as PELCO-P, PELCO-D and PELCO-S. You can use various devices

(such as the matrix, control keyboard or DVR) and protocols to operate PTZ camera.

1.2.4 Proportional Pan and Tilt

 This function keeps the image from moving too fast when there is a large amount of zoom.

 The PTZ camera continually decreases or increases pan and tilt speeds in proportion to depth of zoom.

When zooms speed increases, the camera moving speed becomes slow. When zooms speed decreases,

the camera moving speed becomes fast.

1.2.5 Preset Setup and Call

Preset function is to save the address information (such as PTZ pan/tilt, focus and etc) to the memory so that

you can quickly adjust the dome and PTZ to the correct position. The camera supports a maximum of 255

presets in PELCO-D and PELCO-P protocols.

1.2.6 Auto Scan

Camera scans back and forth regularly along the horizontal field. Here you need to set left and right limit and

scan speed. You can set 5 scanning paths.

1.2.7 Auto Touring

Add addresses into a routine in a desired order and then set time and stop duration for each address. The dome

will begin an auto touring between these addresses. Each touring path can contain max 32 presets.

1.2.8 Auto Pattern

Memorises dome operations such as pan, tilt, and zoom to repeat. You can call it to repeat the previous

operation.

1.2.9 Privacy Masking

Privacy masking is a user-defined, four-sided area that cannot be viewed by you. The masking area will move

with pan and tilt functions and automatically adjust in size as the lens zooms.

1.2.10 IR Night Vision

Whilst set to night vision status, it can use the IR light to spot objects within the monitoring view. You can also

monitor the various environments in low illumination situations.

1.2.11 Action on Alarm

This camera supports three alarm activation operations. There are also 7 alarm inputs (NO/NC). Alarms can be

individually programmed to initiate an associated preset, scanning, or tour when triggered. Dome will return to a

previously programmed state after alarm acknowledgement or to its previous position before alarm.

1.2.12 Auto Flip

As long as you continue to hold the keyboard joystick in the down position, the dome rotates 180 degrees and

repositions itself for uninterrupted viewing of any subjects that passes directly beneath the dome.

1.2.13 Self-diagnosis

There is a self-diagnosis procedure when camera boots up.

 Tilt and vertical engine check

 Camera diagnostics

 Displays dome information and diagnosis information such as address, protocol, baud rate.

1.2.14 Day/Night Mode (B/W & Color Mode)

System supports auto/manual switching in low illumination conditions. You can specify the switch time.

 In the auto mode and photosensitive resistance modes, the camera can automatically switch the CCD

level according to the light change. When in manual mode, you can use the menu or the buttons to

display in color, black and white, and also the schedule switch. All the modes will have automatic

activation operation on the IR lighting, except when set to camera auto mode.

 This function works with the IR night vision function.

1.2.15 Auto Focus

Auto focus allows the lens to remain in focus during zoom-in, zoom-out and motion functions to constantly

provide a vivid image to monitor. You can use the FAR or NEAR buttons to adjust focus manually.

1.2.16 Backlight Compensation

Balance the brightest and darkest sections of a scene to produce a more vivid picture.

1.2.17 Pan Tilt and Zoom

Supports zoom in and zoom out during tilt and pan movement. In this period, focus and iris are both in auto

mode to give you the best angle to monitor.

1.2.18 3D Intelligent Location

When operating the DVR, just click part of the current scene and it will be displayed within the central window. It

will then automatically zoom in to the clicked location. All of these allow you to trace precisely.

1.2.19 Idle Status

When there is no available order, you can use menu to set dome idle status after specified duration. The idle

status includes turn to specified preset or go to scan, tour or pattern function.

1.2.20 Image Stabilizer/Flip

You can enable image stabiliser function and flip within the menu. The flip function allows you to view continuous

video.

2 IR PTZ camera Installation

2.1 Installation Preparation

Basic Requirement

 All installation and operation procedures should conform to your local electrical safety codes.

 Before installation, please open the package and check that all the components are included. Please make

sure the PTZ camera installation environment and installation mode can meet your requirement.

 We assume no liability or responsibility for any type of damage to person(s) or property caused by improper

handling or installation.

Check installation space and installation location intension

Please make sure the installation environment has enough space to install the PTZ camera and its

corresponding bracket. Also make sure the ceiling, wall and the bracket can support the PTZ camera and its

corresponding installation component. Only install on to the surface if it can take 4X the weight of the camera.

About cable

Please select the cable according to your transmission distance.

The minimum video coaxial-cable requirement is:

 75 ohm.

 Full cable with copper conductor

 95% knitted copper shield

International Model

Max Distance

(Ft\M)

RG59/U

750ft (229m)

RG6/U

1,000ft (305m)

RG11/U

1,500ft (457m)

Set dial switch button

Set dial switch button according to control protocol and PTZ camera address (see Chapter 8 for full instructions).

Please keep all package material well for future use

Please keep PTZ camera package material in good condition in case you need to send it back to your supplier.

Non-original packaging material may result in device damage during the transportation.

Check Accessories

Before the installation, please check the accessories one by one according to the packing list. Please make sure

all the components listed are included

2.2 IR PTZ camera and network IR PTZ camera installation

2.2.1 PTZ camera bracket installation

The PTZ camera has several different types of installation brackets. You can refer to the following contents for

detailed information. This section will show you how to install the IR PTZ camera into the wall mount bracket.

2.2.2 Pipe thread bracket installation

Please connect the quick installation port to the wall mount bracket (Pipe thread connection) and then use the

M4 stainless steel bolt to fix securely. Then you can connect the integrated cable to the composite cable of the

flanges. Please connect the corresponding power, video output, RS 485 control, network and alarm input &

output cables respectively (Please connect as your actual requirements). Finally, you can connect the flange to

the quick installation port. See Figure 2-1.

Please note the analog PTZ camera does not have the network cable connection. You can connect the RS485,

video output cable if necessary.

Figure 2-1

VIDIO: Video OUT AUDIO: White = AUDIO IN

RS485: Yellow = A + Black = GND

Orange = B - Red = AUDIO OUT

POWER: Red = AC24V ALARM: Blue = Alarm out

Black = AC24V White = Com 1

Yellow & Green = GND Red = GND

Black = Alarm in 2

2.2.3 Clip wall mount bracket installation

Please connect the flange to the PTZ camera device. Connect the cable port of the flange to the slot of the PTZ

camera one by one (this includes power, video, RS485, network cable and alarm input/output)

Note: you can connect the network cable or the alarm input/output if necessary. After you connected the flange

to the PTZ camera, please install it to the bracket. Use the three inner hex screws to secure. See Figure 2-2.

For the corner mount installation or the pole mount installation, you can also refer to these contents.

Figure 2-2

VIDIO: Video OUT AUDIO: White = AUDIO IN

RS485: Yellow = A + Black = GND

Orange = B - Red = AUDIO OUT

POWER: Red = AC24V

Black = AC24V

Yellow & Green = GND

2.2.4 Secure the PTZ camera to the flange

Please check the rubber airproof ring of the PTZ camera, adjacent to the flange, is fitted correctly. Use the

internal hex screwdriver to fix IR PTZ camera and the flange to complete the installation (see Figure 2-3).

IMPORTANT

Please make sure the airproof ring is firmly secured in the slot. Please make sure you have secured the

inner hex screws firmly. Otherwise, it may result in low waterproof capability and PTZ camera

malfunction.

Figure 2-3

3 Bracket Dimensions

3.1 Wall mount bracket

The wall mount bracket dimensions are shown below. See Figure 3-1.

Ф58

G11

2

4-Ф9

84

119

110

145

235

Figure 3-1

3.2 Hanging mount bracket (Multiple Lengths)

The hanging mount bracket is shown below. See Figure 3-2.

Figure 3-2

The bracket length setup values are：

 200mm

 300mm

 500mm

You just need to replace the

connection pole.

3.3 Corner mount bracket

The corner mount bracket is shown below. See Figure 3-3.

Figure 3-3

3.4 Pole mount bracket

The corner mount bracket is shown below. See Figure 3-4.

Figure 3-4

4 Wall Mount Bracket Installation

4.1 Component Installation

Wall mount bracket and its components are shown below. See Figure 4-1.

Figure 4-1

4.2 Installation

4.2.1 Installation Requirements

The wall mount PTZ camera can be installed in the hard construction wall in either indoor or outdoor

environments. Before the installation, please make sure:

1. The wall is thick enough to install the expansion bolt.

2. The wall can at least sustain the 4x weight of the PTZ camera.

4.2.2 Installation Steps

Please draw four holes in to the wall according to the holes found at the base of the wall mount bracket. Then

you can drill four holes and insert the expansion bolts (not provided). Use four hex bolts and flat washer to fix the

bracket in the expansion bolts. See Figure 4-2.

Figure 4-2

Installation

Hole

Install the PTZ camera in the bracket. See Figure 4-3.

Figure 4-3

5 Hang Mount Bracket Installation

5.1 Component Installation

Hang mount bracket and its components are shown below. See Figure 5-1.

Figure 5-1

5.2 Installation

5.2.1 Installation Requirements

The hang mount PTZ camera can be installed on to a hard construction wall in either indoor or outdoor

environments. Before the installation, please make sure:

1. The wall is thick enough to install the expansion bolt.

2. The wall can at least sustain the 4x weight of the PTZ camera.

5.2.2 Installation Steps

Loosen the M4 bolt on the flange side to separate the flange from the steeve. Pull the integration cable through

the airproof slot of the bottom of the flange and then connect to the centre hole of the flange. Please secure the

flange in the ceiling. See Figure 5-2. Please note, if the PTZ camera is installed in an outdoor environment,

you need to paste the silica gel on the surface of the flange and the surface and the cable exit.

Figure 5-2

Silica gel

Connect

to flange

Page is loading ...

QVIS APOIR-PTZ23 User manual

Related papers

Other documents