Flotec FP0S1300X Owner's manual

Brand: Flotec

Model: FP0S1300X

Category: Water pumps

Type: Owner's manual

This manual is also suitable for

P.O. Box 342, Delavan, WI 53115

Phone:

1-800-365-6832

Fax:

1-800-526-3757

E-Mail:

info@flotecwater.com

Web Site:

http://www.flotecwater.com

OWNER’S MANUAL

Submersible Utility Pumps

Series FP0S1300X, FP0S1600X,

FP0S1100X, FP0S1250X

NOTICE D’UTILISATION

Pompes utilité submersibles

Série FP0S1300X, FP0S1600X,

FP0S1100X, FP0S1250X

MANUAL DEL USUARIO

Bombas sumergibles

de uso general

Serie FP0S1300X, FP0S1600X,

FP0S1100X, FP0S1250X

Installation/Operation/Parts

For further operating,

installation, or maintenance

assistance:

Call 1-800-365-6832

English ...................... Pages 2-3

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation,

l’installation ou l’entretien,

Composer le

1 (800) 365-6832

Français ................... Pages 4-5

Instalación/Operación/Piezas

Para mayor información sobre

el funcionamiento, instalación o

mantenimiento de la bomba:

Llame al 1-800-365-6832

Español....................Paginas 6-7

FP288 (Rev. 4/27/07)

Series FP0S1300X/FP0S1600X Series FP0S1100X/FP0S1250X

English 2

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

GENERAL SAFETY

Electrically powered sump pumps normally give many years of trouble-

free service when correctly installed, maintained, and used. However,

unusual circumstances (interruption of power to the pump, dirt/debris

in the sump, flooding that exceeds the pump’s capacity, electrical or

mechanical failure in the pump, etc.) may prevent your pump from

functioning normally. To prevent possible water damage due to flood-

ing, consult your retailer about a secondary AC sump pump, a DC

backup sump pump, and/or a high water alarm. See the

“Troubleshooting Chart” in this manual for information about common

sump pump problems and remedies. For more information, see your

retailer or call Flotec customer service at 1-800-365-6832.

1. Know the pump application, limitations, and potential hazards.

Do not use in explosive atmospheres. Pump water

only with this pump. Failure to follow this warning can result in

personal injury and/or property damage.

Risk of flooding. If a flexible discharge hose is

used, make sure pump is secured in sump to prevent movement.

Failure to secure pump may allow pump movement, switch

interference and prevent pump from starting or stopping.

2. Make certain power source conforms to requirements of your

equipment.

3. Disconnect power before servicing.

4. Release all pressure within system before servicing any component.

5. Drain all water from system before servicing.

6. Secure discharge line before starting pump. An unsecured dis-

charge line will whip, possibly causing personal injury and/or prop-

erty damage.

7. Check hoses for weak or worn condition before each use, making

certain all connections are secure.

8. Periodically inspect pump and system components. Keep sump,

pump and system free of debris and foreign objects. Perform rou-

tine maintenance as required.

9. Provide means of pressure relief on pumps whose discharge line

can be shut-off or obstructed.

10. Personal Safety:

a. Wear safety glasses at all times when working with pumps.

b. Keep work area clean, uncluttered and properly lighted –

replace all unused tools and equipment.

c. Keep visitors at a safe distance from the work area.

d. Make workshop child-proof – with padlocks, master switches,

and by removing starter keys.

11. When wiring an electrically driven pump, follow all electrical and

safety codes, as well as most recent National Electrical Code (NEC)

and Occupational Safety and Health Act (OSHA).

Pump motor is equipped with an automatic reset-

ting thermal protector and may restart unexpectedly.

12. Risk of electric shock. This equipment is only for use

on 115 volt (single phase) and is equipped with an approved 3-

conductor cord and 3-prong, grounding-type plug.

To reduce risk of electric shock, be certain that it is

connected to properly grounded, grounding-type receptacle.

Where a 2-prong wall receptacle is encountered, it must be

replaced with properly grounded 3-prong receptacle installed in

accordance with the National Electrical Code and local codes and

ordinances.

13. All wiring should be performed by a qualified electrician.

14. Protect electrical cord from sharp objects, hot surfaces, oil, and

chemicals. Avoid kinking cord. Replace or repair damaged or worn

cords immediately.

15. Use wire of adequate size to minimize voltage drop at motor. Refer

to most recent National Electrical Code.

16. Do not touch an operating motor. Modern motors are designed to

operate at high temperatures.

17. Do not use in water where fish are present.

SPECIFICATIONS

Power supply required .......................................................115V, 60 HZ.

Liquid Temp. Range ....................................................Max. 77°F (25°C)

Operation Position ......................................................................Vertical

Individual Branch Circuit Required ............................................15 Amp

Operating Depth Beginning min...........................................1/2"

(water level) Ending max.............................................3/16"

Discharge......................................................................1" NPT (25 mm)

NOTICE: For models FP0S1100X and FP0S1250X, maintain minimum

water level of 4" (127mm) to prevent overheating.

DESCRIPTION

The submersible pump is designed for water removal in home applica-

tions. Pump can be used for sump service and dewatering. Unit is con-

structed of hi-impact corrosion resistant plastic. Screened inlet pre-

vents large solids from entering pump.

NOTICE: This unit is not designed for applications involving salt water or

brine! Use with salt water or brine will void warranty.

PERFORMANCE

INSTALLATION

Do not use power cord to lift motor. Always use handle.

1. Pump should be located and should rest on level solid foundation.

Do not suspend pump by means of discharge pipe or power cord.

Keep pump inlet screen clear.

2. Thread outlet pipe into pump body carefully to avoid stripping or

crossing threads.

a. To install with garden hose, install adapter provided with pump.

NOTICE: To keep friction as low as possible, hose must be 3/4”

or larger. Keep hose as short as possible.

b. To install with rigid pipe, use plastic pipe. Wrap thread with

Teflon tape or use Plasto Joint Stik*. Screw pipe into pump

hand tight +1 - 1-1/2 turns.

3. Power Supply: Pump is designed for 115V., 60 HZ. operation and

requires an individual branch circuit of 15 amperes or more capaci-

ty. It is supplied with a 3-wire cord set with grounding-type plug

for use in a 3-wire, grounded outlet. 3 wire extension cord, of at

least 14 AWG (2mm

) size is suggested, with larger sizes for runs

over 25 ft (7M). For safety, pump should always be electrically

grounded to a suitable electrical ground such as a grounded water

pipe or a properly grounded metallic raceway, or ground wire sys-

tem. Do not cut off the round grounding prong.

The pump motor is equipped with automatic reset-

ting thermal protector and may restart unexpectedly. Protector

tripping is indication of motor overloading as a result of operat-

ing pump at low heads (low discharge restriction), excessively

high or low voltage, inadequate wiring, incorrect motor connec-

tions, or a defective motor or pump.

OPERATION

Risk of burns or death from electric shock. Do not

handle pump or pump motor with wet hands or when standing on

wet or damp surface, or in water. Disconnect power from pump

before handling, servicing, or attempting to repair pump.

1. The pump must be standing in at least 1/2” (12.7mm) of water

before starting it (one inch (25.4 mm) is better). The shaft seal is

water lubricated and may be damaged if pump runs dry.

2. After starting, the pump will lower the water level to 3/16” (4.75

mm) before losing suction. It will not pick up water less than 3/16”

deep when running and will not operate successfully if started in

only 3/16” of water.

3. Do not leave pump unattended! If the pump has been operating

satisfactorily and the discharge stream suddenly stops coming out

of the hose, stop the pump immediately; do not allow it to run dry.

A mop or squeegee will be needed to remove remaining water.

4. The motor is equipped with an automatically resetting thermal

overload protector. If the motor gets too hot, the overload protec-

tor will stop the motor before it is damaged. When the motor has

cooled sufficiently, the overload protector will reset itself and the

motor will restart.

GPH (LPH) AT TOTAL FEET (M)

3'(0.91) 5'(1.52) 10'(3.05) 15'(4.57) 16'(4.80) 20'(6.09) 22'(6.70)

FP0S1100X

975 gal 915 gal 700 gal 265 gal 0 gal – –

(3 690 L) (3 460 L) (2 650 L) (1 000 L) (0 L) – –

GPH (LPH) AT TOTAL FEET (M)

3'(0.91) 5'(1.52) 10'(3.05) 15'(4.57) 18'(5.49) 20'(6.09) 22'(6.70)

FP0S1250X

1140 gal 1050 gal 840 gal 480 gal 0 gal – –

(4 315 L) (3 975 L) (3 180 L) (1 817 L) (0 L) – –

FP0S1300X

1320 gal 1250 gal 930 gal 660 gal 630 gal 0 gal –

(4 996 L) (4 731 L) (3 520 L) (2 498 L) (2 385 L) (0 L) –

FP0S1600X

1600 gal 1524 gal 1260 gal 924 gal 648 gal 372 gal 0 gal

(6 056 L) (5 768 L) (4 769 L) (3 497 L) (2 452 L) (1 408) (0 L)

English 3

For parts or assistance, call Flotec Customer Service at 1-800-365-6832

NOTICE: If the overload protector stops the pump repeatedly, dis-

connect the power from the pump and check it to find the problem.

Low voltage, long extension cords, clogged impeller, too much

back pressure in the discharge hose (as when pumping through

50’ (15 M) of coiled hose), or running pump with no load, can all

cause excessive cycling and overheating.

5. For Model FP0S1300X, the water being pumped cools the motor,

allowing the pump to run continuously at any depth of water above

3/16”. However, if the motor overload stops the pump, allow it to

cool for one hour before restarting. Motor will not restart before

the overload has cooled.

6. For Models FP0S1100X and FP0S1250X, do not try to run the

pump continuously when the water level is below 4” (102mm) or

about 1/3 of the way up the motor casing, as it will overheat. If the

motor overheats and the overload stops the pump, allow it to cool

for one hour before restarting. Motor will not restart before the

overload has cooled.

AIRLOCKS

When a pump airlocks, it runs but does not move any water. An airlock

will cause the pump to overheat and fail. This pump has an anti-airlock

hole in the bottom of the pump body. If you suspect an airlock, unplug

the pump, clean out the anti-airlock hole with a paper clip or piece of

wire, and restart the pump.

IMPORTANT: This hole allows the pump to start priming within 15 sec-

onds in as little as 1/2” of water. NEVER restart pump in less than 1/2”

of water. Leakage from the anti-airlock hole is normal.

* Lake Chemical Co., Chicago, Illinois

Key Part Description Qty. Part No.

1 Screen 1 PS8-5P

2 Shield 1 PS70-3P

3 Impeller - S1300X 1 PS5-24P

3 Impeller - S1600X 1 PS5-25P

4 Motor 1 **

5 Power Cord 1 PS117-54-TSU

• Garden Hose Adapter 1 FT0013-43

Models

FP0S1300X-08

FP0S1600X-08

TROUBLESHOOTING

** If motor fails, replace entire pump.

• Not Illustrated.

Key Part Description Qty. Part No.

1 Lower Base Plate 1 FP0005797A

2 Impeller (FP0S1100X) 1 PS5-24PA

2 Impeller (FP0S1250X) 1 PS5-24P

3 Volute Gasket 1 U9-406

4 Upper Base Plate 1 FP0005796A

5 Motor 1 **

6 Power Cord 1 PS117-54-TSU

• Garden Hose Adapter 1 FT0013-43

Models

FP0S1100X

FP0S1250X-08

** If motor fails, replace entire pump.

• Not Illustrated.

Anti-Airlock

Hole

5125 0905

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Pump won’t Blown fuse If blown, replace with fuse of proper size

start or run

Low line voltage If voltage under recommended minimum, check size of wiring

from main switch on property. If OK, contact power company.

Defective motor Replace pump

Impeller If impeller won’t turn, for models FP0S1100X and FP0S1250X,

remove housing; for model FP0S1300X, remove screen.

Locate source of binding

Pump operates but Low line voltage Use only 14 gauge or larger extension cords. Use short extension cords

delivers little or when necessary

no water

Something caught in impeller Clean out impeller

Small diameter garden hose Use larger diameter garden hose or 1” flexible pipe. Eliminate any

or long discharge line excess hose. Short hoses work best

Check valve installed without Drill a 1/16" - 1/8" (1.6 - 3.2 mm) dia. hole between pump

vent hole discharge & check valve

Air lock Turn off pump for a few seconds, clean out anti-airlock hole and restart pump

Coils or bends in hose Straighten hose

3rd

Anti-Airlock

Hole

Tighten 1st

Orient Part Number with

Anti-Airlock Hole as shown

2nd

Install shield and tighten

screws in sequence as shown.

Page is loading ...

FLOTEC LIMITED WARRANTY

FLOTEC warrants to the original consumer purchaser (“Purchaser”) of its products that they are free from defects in material or workmanship.

If within twelve (12) months from the date of the original consumer purchase any such product shall prove to be defective, it shall be repaired or replaced at FLOTEC’s option, subject to the terms and

conditions set forth below. Your original receipt of purchase is required to determine warranty eligibility.

Exceptions to the Twelve (12) Month Warranty

Product Warranty Period

Drill Pump, Pitcher Pump, In-line Water Filter Cartridge 90 days

1/3 HP Submersible Sump Pumps, INTELLIPUMP (Model FP0S1775A)

2 Years

Back-up Sump Pump System (Model FP2800DCC)

4" Submersible Well Pumps, 1/2 HP Submersible Sump Pumps

3 Years

Models FPSC2200A-10 and FPSC2250A-10

Pre-Charge Water System Tank, Models FPSC3200A-10 and FPSC3250A-10 5 Years

Floodmate

7000 (Model FP0S6000A), Ironmate

(Model FPSC4550A)

Sewage Ejector (Model FPSE3601A), Pedestal Sump Pump (Model FPPSS5000) Lifetime

Utility Pump (Model FPSC1725X), Submersible Sump Pump (Model FPSC4550A-10)

General Terms and Conditions

Purchaser must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty shall not apply to acts of God, nor shall it apply to products which, in the

sole judgement of FLOTEC, have been subject to negligence, abuse, accident, misapplication, tampering, alteration; nor due to improper installation, operation, maintenance or storage; nor to

other than normal application, use or service, including but not limited to, operational failures caused by corrosion, rust or other foreign materials in the system, or operation at pressures in

excess of recommended maximums.

Requests for service under this warranty shall be made by returning the defective product to the Retail outlet or to FLOTEC as soon as possible after the discovery of any alleged defect.

FLOTEC will subsequently take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than 30 days after the term of

the warranty.

This warranty sets forth FLOTEC’s sole obligation and purchaser’s exclusive remedy for defective products.

FLOTEC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICABLE EXPRESS WARRANTIES

PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not

apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

FLOTEC • P.O. Box 342 • Delavan, WI U.S.A. 53115

Phone: 1-800-365-6832 • Fax: 1-800-526-3757 • E-Mail: info@flotecwater.com • Web Site: http://www.flotecwater.com

GARANTIE LIMITÉE FLOTEC

FLOTEC garantit à l’acheteur-utilisateur initial de ses produits (“Acheteur”) contre tout défaut de fabrication et de matériaux.

Tout produit reconnu défectueux dans les douze (12) mois qui suivent la date d’achat d’origine sera remplacé ou réparé à la discrétion de FLOTEC, selon les conditions stipulées ci-dessous. La

preuve d’achat est exigée pour déterminer l’admissibilité à la garantie.

Exceptions à la garantie de douze (12) mois

Produits Période de garantie

Pompe adaptable sur perceuse, pompe d’amorçage, cartouche de filtre à eau en ligne 90 jours

Pompes submersibles de puisard INTELLIPUMP, de 1/3 ch (Modèle FP0S1775A)

2 ans

Système de pompage de secours de puisard de soutien (Modèle FP2800DCC)

Pompes submersibles pour puits de 4 pouces, Pompes submersibles de puisard de 1/2 ch

3 ans

Modèles FPSC2200A-10 et FPSC2250A-10

Réservoirs préchargés de système d’eau, Modèles FPSC3200A-10 et FPSC3250A-10 5 ans

Floomate

7000 (Modèle FP0S6000A), Ironmate

(Modèle FPSC4550A)

Éjecteur d’eaux d’égout (Modèle FPSE3601A), Pompe sur colonne de puisard (Modèle FPPSS5000) À vie

Pompe à usage général (Modèle FPSC1725X), Pompe submersible de puisard (Modèle FPSC4550A-10)

Conditions générales

L’Acheteur s’engage à payer tous les frais de main-d’œuvre et d’expédition nécessaires au remplacement du produit couvert par la garantie. Cette garantie ne couvrira pas les cas de force

majeure, et ne s’appliquera pas aux produits qui, du seul avis de FLOTEC, ont fait l’objet de négligence, d’utilisation abusive ou incorrecte, d’accident, de modification ou d’altération ; ni aux

produits qui n’ont pas été installés, utilisés, entreposés ou entretenus correctement ; ni à ceux qui n’ont pas été utilisés ou entretenus normalement, y compris, mais sans s’y limiter, aux pro-

duits ayant des pannes de fonctionnement causées par la corrosion, la rouille ou autre corps étranger dans le système, ou à des produits ayant fonctionné à des pressions dépassant la limi-

te maximale recommandée.

Les demandes de service en vertu de la présente garantie seront faites en retournant le produit défectueux au détaillant ou à FLOTEC dès la découverte de tout défaut allégué. FLOTEC prendra alors

les mesures correctives aussi rapidement qu’il est raisonnablement possible. Aucune demande de service en vertu de la présente garantie ne sera acceptée si elle est reçue plus de 30 jours après

l’expiration de la dite garantie.

La présente garantie énonce la totalité des obligations de FLOTEC et le seul recours possible de l’Acheteur dans le cas de produits défectueux.

FLOTEC NE SERA TENU RESPONSABLE D’AUCUN DOMMAGE INDIRECT, ACCIDENTEL OU FORTUIT QUEL QU’IL SOIT.

LES PRÉSENTES GARANTIES SONT EXCLUSIVES ET TIENNENT LIEU DE TOUTE AUTRE GARANTIE EXPRESSE. LES GARANTIES IMPLICITES, Y COMPRIS, MAIS SANS S’Y LIMI-

TER, LES GARANTIES IMPLICITES AYANT TRAIT À LA COMMERCIABILITÉ ET À L’ADAPTATION À UN USAGE PARTICULIER, NE DÉPASSERONT PAS LA DURÉE DES GARANTIES EX-

PRESSES APPLICABLES STIPULÉES DANS LES PRÉSENTES.

Certaines provinces n’autorisent pas d’exclure ou de limiter les dommages fortuits ou indirects ou de limiter la durée d’une garantie implicite ; il se peut donc que les limitations ou exclusions

ci-dessus ne s’appliquent pas à votre cas. La présente garantie vous donne des droits juridiques spécifiques et vous pouvez en avoir d’autres qui varient d’une province à l’autre.

FLOTEC • P.O. Box 342 • Delavan, WI U.S.A. 53115

Téléphone: 1-800-365-6832 • Télécopieur: 1-800-526-3757 • Courrier électronique: inf[email protected] • Site Web: http://www.flotecwater.com

GARANTÍA LIMITADA DE FLOTEC

FLOTEC garantiza al comprador consumidor original (“Comprador”) de sus productos, que éstos se encuentran libres de defectos de material o mano de obra

Si dentro de los doce (12) meses de la fecha original de la compra cualquiera de los productos demostrara estar defectuoso, el mismo será reparado o reemplazado, a opción de FLOTEC con su-

jeción a los términos y condiciones expuestos a continuación. Se requiere su recibo original de compra para determinar si se encuentra bajo garantía.

Excepciones a la Garantía por Doce (12) Meses

Producto Período de garantía

Bomba a taladro, Bomba a émbolo, Cartucho del filtro de agua en línea 90 días

Bombas de sumidero sumergibles INTELLIPUMP de 1/3 HP (Modelo FP0S1775A) 2 años

Sistema de bomba de sumidero de respaldo (Modelo FP2800DCC)

Bombas de pozo sumergibles de 4", Bombas de sumidero sumergibles de 1/2 HP 3 años

Modelos FPSC2200A-10 y FPSC2250A-10

Tanque precargado del sistema de agua Modelos FPSC3200A-10 y FPSC3250A-10 5 años

Floodmate

7000 (Modelo FP0S6000A), Ironmate

(Modelo FPSC4550A)

Eyector de aguas residuales (Modelo FPSE3601A), Bomba de pedestal para sumidero (Modelo FPPSS5000) De por vida

Bomba para uso general (Modelo FPSC1725X), Bomba de sumidero sumergible (Modelo FPSC4550A-10)

Términos y Condiciones Generales

El comprador debe pagar todos los gastos de mano de obra y transporte necesarios para reemplazar el producto cubierto por esta garantía. Esta garantía no se aplicará a hechos de fuerza

mayor, ni se aplicará a los productos que, a juicio exclusivo de FLOTEC, hayan sido objeto de negligencia, abuso, accidente, aplicaciones contraindicadas, manejo indebido, alteraciones; ni

debido a instalación, funcionamiento, mantenimiento o almacenaje incorrectos; ni a ninguna otra cosa que no sea su aplicación, uso o servicio normales, incluyendo, pero no limitado a, fallas

operacionales causadas por corrosión, oxidación u otros elementos extraños en el sistema, o funcionamiento a presión por encima del máximo recomendado.

Los pedidos de servicio bajo los términos de esta garantía serán efectuados mediante la devolución del producto defectuoso al Vendedor o a FLOTEC, tan pronto como sea posible, después

de localizado cualquier supuesto defecto. FLOTEC tomará luego acción correctiva, tan pronto como sea razonablemente posible. Ningún pedido de servicio bajo esta garantía será aceptado

si se recibe más de 30 días después del término de la garantía.

Esta garantía establece la obligación única de FLOTEC y el remedio exclusivo del comprador en el caso de productos defectuosos.

FLOTEC NO SERÁ RESPONSABLE POR NINGÚN DAÑO CONSECUENTE, INCIDENTAL O CONTINGENTE DE NINGUNA NATURALEZA.

LAS GARANTÍAS ANTERIORES SON EXCLUSIVAS Y REEMPLAZAN CUALESQUIERA OTRAS GARANTÍAS EXPRESAS. LAS GARANTÍASIMPLÍCITAS, INCLUYENDO, PERO NO LIMI-

TADAS A, LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD Y APTITUD PARA UN PROPÓSITO EN PARTICULAR, NO DEBERÁN EXCEDER EL PERÍODO DE DURACIÓN DE LAS

GARANTÍAS EXPRESAS APLICABLES AQUÍ PROVISTAS.

Algunos estados no permiten la exclusión o limitación de daños incidentales o consecuentes ni las limitaciones respecto a la duración de garantías implícitas; de modo que las limitaciones o

exclusiones precedentes pueden no aplicarse en su caso. Esta garantía le concede derechos legales específicos. Usted puede tener, además, otros derechos que varían de un estado a otro.

FLOTEC • P.O. Box 342 • Delavan, WI U.S.A. 53115

Teléfono: 1-800-365-6832 • Fax: 1-800-526-3757 • e-Mail (correo electrónico): [email protected] • Dirección web: http://www.flotecwater.com