2. OTC
  3. 6470

OTC 6470 Operating instructions

  • Hello! I've reviewed the provided operating instructions for the OTC Ford Camshaft Sensor Synchronizer Tool, models 6470 and 511537. This document includes important steps for engaging the tool, and installing the sensor housing in various Ford vehicles. I'm here to help answer your questions about its use and features, such as sensor housing positioning and tool engagement.
  • What is the Ford Camshaft Sensor Synchronizer Tool used for?
    What Ford models is this tool compatible with?
    What is the primary caution before using this tool?
    What must you do before engaging the tool?
Form No. 107094
Operating Instructions
for: 6470
(511537)
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
© Bosch Automotive Service Solutions LLC
July 25, 2014 Rev. C
Ford Camshaft Sensor Synchronizer Tool
Application: 1999 – 2002 5.0L V8 Explorer, Mountaineer
2004 – 2007 3.9L Freestar (VIN 6)
2004 3.9L Monterey (VIN 6)
1999 – 2004 3.8L V6 Mustang
1999 – 2003 3.8L V6 Windstar
CAUTION: Before removing the camshaft sensor housing assembly,
note the position of the camshaft sensor electrical connector. To prevent
equipment damage, the connector MUST be reassembled in the same
position during installation.
1. Rotate crankshaft to set No. 1 cylinder at top dead center of compression
stroke.
2. Engage camshaft sensor housing vane in slot of tool No. 6470 (511537).
3. Rotate tool on camshaft sensor housing until tool engages housing notch.
(Tool should be square and in contact with entire top of housing.)
4. Install camshaft sensor housing and tool assembly into engine according
to instructions in the vehicle service manual. Torque fasteners to factory
specications.
WARNING: Wear eye
protection that meets ANSI
Z87.1 and OSHA standards.
Camshaft
Sensor
Housing
No. 6470
(511537)
NOTE: Same as Ford No. 303-630.
Form No. 107094
Operating Instructions
for: 6470
(511537)
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
© Bosch Automotive Service Solutions LLC
July 25, 2014 Rev. C
Ford Camshaft Sensor Synchronizer Tool
Application: 1999 – 2002 5.0L V8 Explorer, Mountaineer
2004 – 2007 3.9L Freestar (VIN 6)
2004 3.9L Monterey (VIN 6)
1999 – 2004 3.8L V6 Mustang
1999 – 2003 3.8L V6 Windstar
CAUTION: Before removing the camshaft sensor housing assembly,
note the position of the camshaft sensor electrical connector. To prevent
equipment damage, the connector MUST be reassembled in the same
position during installation.
1. Rotate crankshaft to set No. 1 cylinder at top dead center of compression
stroke.
2. Engage camshaft sensor housing vane in slot of tool No. 6470 (511537).
3. Rotate tool on camshaft sensor housing until tool engages housing notch.
(Tool should be square and in contact with entire top of housing.)
4. Install camshaft sensor housing and tool assembly into engine according
to instructions in the vehicle service manual. Torque fasteners to factory
specications.
WARNING: Wear eye
protection that meets ANSI
Z87.1 and OSHA standards.
Camshaft
Sensor
Housing
No. 6470
(511537)
NOTE: Same as Ford No. 303-630.
/