Astria Fireplaces DRT4036/42 Instruction Sheet

Brand: Astria Fireplaces

Model: DRT4036/42

Category: Fireplaces

Type: Instruction Sheet

This manual is also suitable for

Astria Fireplaces DRT4036/42 offer a captivating ambiance with realistic flames that mimic a wood fire, enhancing the coziness of any space. These fireplaces provide an ample heating capacity, making them ideal for large rooms up to 400 square feet. With the convenience of remote control, you can effortlessly adjust the flame height and temperature settings from across the room. Additionally, the included ember bed provides an authentic fireplace experience, while the safety features ensure peace of mind during operation.

Removing Barrier/Glass Door

Gloves must be worn when removing/replacing glass door. If glass

is broken, tape remaining glass frame before removing.

1. Remove bottom access panel.

2. Remove barrier by holding the barrier in front of the glass door

and slide it up into the channel underneath the upper front face

to release it from bottom channel then pull it out and away from

the ﬁreplace (see Figure 1a, page 2).

3. Unlock 2 door latches on bottom of ﬁrebox.

4. Tilt open glass door 30° from bottom of ﬁrebox and lift up to

release door from ﬁrebox top retainer (see Figure 2, page 2).

5. To replace the barrier and glass door, reverse steps above.

WARNING: Reinstall any barrier removed before

operating the ﬁreplace. The barrier is designed to

reduce the risk of burns from hot glass. Do not operate

the ﬁreplace without the barrier installed.

This conversion kit must be installed by a qualiﬁed

service agency.

Read these instructions completely before installing this conversion kit.

Before proceeding, make sure gas control valve is in the OFF posi-

tion, all electrical power to the appliance is off and ﬁreplace is cool

to the touch.

CAUTION: The gas supply shall be shut off prior to disconnect-

ing the electrical power before proceeding with the conversion.

Parts included with this kit:

Part No. Description Quantity

900693-00 Instruction Sheet 1

23100 Front Burner Oriﬁce LP (#56) 1

23567 Rear Burner Oriﬁce LP (#55) 1

900696-03 Conversion Label 1

106080-01 Conversion Information Label 1

125699-02 Pilot LP 1

Tools Required

• 3/8" Hex Socket Wrench or Adjustable Wrench

• 7/8" Open End Wrench or Adjustable Wrench

• 3/4" Open End Wrench or Adjustable Wrench

• Slotted Screwdriver

• Needle Nose Pliers

• #2 Short Phillips Screwdriver

• Thread Sealant (Resistant to Propane/LP)

ACCESSING FIREPLACE

The gas control valve and main burner oriﬁce are located under ﬁrebox

ﬂoor of appliance and are accessed by removing bottom access door.

2 oriﬁces are located in burners and are accessed by removing the

bottom access panel, barrier, glass door and burner.

Removing Bottom Access Panel

Remove bottom access panel by pulling top end forward and away

from appliance (see Figure 1). To replace removed item, reverse

procedure above. Figure 1 - Removing Bottom Access Panel

Bottom Access

Door

Barrier

PCD-42S2 (F2815) CONVERSION KIT

INSTALLATION INSTRUCTIONS

For use when Converting Sentinel42TEN

Fireplaces and DRT4042TEN Fireplaces

From Natural Gas to Propane/LP Gas

P/N 900693-00 Rev. NC 07/2016

For more information, visit IHP.US.com

IHP.US.com 900693-00_NC

BURNER ORIFICE CONVERSION AND PILOT CONVERSION

Figure 1a - Removing Barrier

Channel

Barrier

Frame

Slot

Figure 2 - Removing Glass Door

Glass Door

Door Latch

Figure 3 - Removing Oriﬁce for Conversion (Valve Shown

Removed from Base for Clarity

Grate

Base

Removable Logs

Burner

Base

Rear

Oriﬁce

Logset

Bulkhead

Fitting

Main

Burner

Andiron

Assembly

Pilot

Shield

Top

Pilot

Shield

Front

Oriﬁce

Elbow

Fitting

Air

Shutter

1. Remove andiron by lifting up and away from back of ﬁreplace

(see Figure 3).

2. Carefully lift 3 loose logs from log stack.

3. Remove hex nuts that attach pilot shield and grate base to burner

base and 2 screws on side of pilot shield top.

4. Remove main burner from grate base by removing screw located

at right inner corner of ﬁrebox, and lifting up and toward the right

(see Figure 3).

5. Remove log set with grate base by holding sides of grate base

and lifting carefully to clear front burner oriﬁce on right and pilot

shield on the left.

6. Remove NG oriﬁce from elbow and bulkhead ﬁttings. Apply a

light amount of propane/LP resistant sealant to threaded end of

LP oriﬁces (#55 and 56) supplied with kit. Thread LP oriﬁces into

ﬁttings and tighten.

7. Adjust front burner air shutter and rear tube burner air shutter to

fully open position.

8. Replace pilot assembly with pilot P/N 125699-02.

9. Reinstall log set with grate base, main burner and loose logs

removed in step 2, 3 and 4.

IHP.US.com

900693-00_NC 3

Lighting Instruction Plate

Conversion Label

Figure 5 - Apply Conversion Labels over Existing Certiﬁcation

Label on Lighting Instruction Plate

GAS CONTROL VALVE CONVERSION

The gas control valve is convertible from natural to propane/LP gas

by a simple rotary knob located on the front face of the valve (see

Figure 4).

1. Remove the black cap by pulling the cap straight off. Note: the position

of the marker on the shaft of the simple rotary knob. This mark will

point to NAT to LP that indicates the type of gas the valve is set on.

2. To convert the control valve back to the factory setting (LP), push

in the simple rotary knob and rotate 90°. Note: the marker will

now point to LP and the shaft will stay in.

3. After the conversion has been made, check the outlet pressure

with a manometer. The factory setting on the internal regulator

is 3.5" w.c. for natural and 10.5" w.c. for propane/LP.

4. Replace black cover cap.

Note: in replacement and conversion use only new parts provided.

When converting to different gas you must also change pilot and

burner oriﬁces.

CONVERSION LABELING AND PLACEMENT

1. Apply conversion label over top of existing certiﬁcation label (see

Figure 5). Existing certiﬁcation label is located on lighting instruc-

tions plate inside gas valve compartment area. With permanent

ink, print previous model number on label in space provided (see

Figure 6).

2. After ﬁlling data required on conversion information label (see

Figure 7), afﬁx it to ﬂoor of appliance where it is easily seen when

bottom access door is removed.

Conversion Label

VENTED GAS FIREPLACE

Conversion Kit Model

Type of Gas

Previous Model #

PFS

Figure 6 - Print Previous

Model Number on

Conversion Label

Figure 7 - Conversion

Information Label

CONVERSION INFORMATION LABEL

This appliance was converted on

___ - ___ - ___ to ______________ gas

with Kit No. _______________________

by _____________________________

_____________________________

____________________________

_____________________________

(name and address of organization making

this conversion), which accepts the

responsibility that this conversion has been

properly made.

106080-01

Day Month Year

Figure 4 - Change Simple Rotary Knob from NAT to LP

Pilot Adj.

Inlet

Outlet

NATURAL TO PROPANE

CONVERSION SHAFT

(UNDER CAP)

NAT

Main

Pilot

FINAL PREPARATION

1. Leak check gas control and any connections you've made be-

fore operating appliance. Refer to Checking Gas Connections in

owner's manual.

2. Reinstall glass door and close latches.

3. Replace barrier and reinstall bottom access panel.

The conversion is now complete.

To operate your ﬁreplace, refer to Operating Fireplace in your appli-

ance owners manual.

WARNING: Test all gas piping and connections,

internal and external to unit, for leaks after installing

or servicing. Correct leaks at once.

WARNING: Never use an open ﬂame to check for

a leak. Apply noncorrosive leak detection ﬂuid to

all joints. Bubbles forming show a leak. Correct all

leaks at once.

WARNING: This conversion kit shall be installed

be a qualiﬁed service agency in accordance with the

manufacturer's instructions and all applicable codes

and requirements of the authority having jurisdiction.

If the information in these instruction is not followed

exactly, a ﬁre, explosion or production of carbon mon-

oxide may result causing property damage, personal

injury or loss of life. The qualiﬁed service agency is

responsible for the proper installation of this kit. The

installation is not proper and complete until the opera-

tion of the converted appliance is checked as speciﬁed

in the manufacturer's instructions supplied with the kit.

Innovative Hearth Products reserves the right to make changes at any time, without notice, in

design, materials, speciﬁcations, prices and also to discontinue colors, styles and products.

Consult your local distributor for ﬁreplace code information.

P/N 900693-00 Rev. NC 07/2016 1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

TECHNICAL SERVICE

You may have further questions about installation, operation, or

troubleshooting. Please contact your IHP dealer for any questions or

concerns. When contacting your dealer please have the model name/

number of your conversion kit ready. You can also visit our website

at IHP.US.com.

Astria Fireplaces DRT4036/42 Instruction Sheet

Brand: Astria Fireplaces

Model: DRT4036/42

Category: Fireplaces

Type: Instruction Sheet

This manual is also suitable for

Download PDF

report

Astria Fireplaces DRT4036/42 Instruction Sheet

This manual is also suitable for

Astria Fireplaces DRT4036/42 Instruction Sheet

Related papers

Other documents