Navman X300 Owner's manual

Brand: Navman

Model: X300

Type: Owner's manual

X300 1-1

NAVMAN

English 1-3

Deutsch 2-1

Francaise 3-1

Italiano 4-1

Espana 5-1

Português 6-1

X300

1-2

NAVMAN

X300 1-3

NAVMAN

English

USER GUIDE

X300 – English

X300

1-4

NAVMAN

Navman’s 300 series GPS Sport.Tools provide an affordable and

reliable way to track and store a variety of personal performance

indicators.

Please read this guide carefully and familiarize yourself with

the interface and functions, as well as the intended use and

limitations of the Navman X300 GPS Sport.Tool.

This product complies with CE, FCC, Canada 210, and C-Tick

regulations.

Operation is subject to the following two conditions:

(1) this device may not cause interference

(2) this device must accept any interference, including interference that

may cause undesired operation of the device.

WARNING: Entering information or handling the Navman

Sport.Tool while moving is unsafe and may cause you to

be distracted or fail to observe safe practices necessary to

avoid death, serious injury, collisions or accidents to you or

others. Use the memory functions to review data when you

are not moving.

CAUTION: The Navman X300 GPS Sport.Tool is intended

for recreational use only. Do not use this product for

obtaining measurements that require professional or

industrial precision. Consult your physician before starting

or changing any exercise programs.

Welcome

X300 1-5

NAVMAN

Content

X300 - Content

1.0 General information 1-6

1.1 Checklist 1-6

1.2 Care and maintenance 1-6

1.3 Water resistance 1-6

1.4 Altitude measurement 1-6

1.5 Changing the battery 1-7

2.0 Navman X300 interface 1-8

2.1 Button functions 1-8

2.2 Display screen 1-8

3.0 Getting started 1-9

3.1 Be outdoors 1-9

3.2 Fit the X300 1-9

3.3 Startup 1-9

3.3.1 Enter setup 1-10

3.3.2 Start normal operation 1-10

4.0 Setup 1-11

4.1 Setting options 1-11

4.1.1 Set time format 1-12

4.1.2 Set date format 1-12

4.1.3 Calc up 1-13

4.1.4 Beep 1-14

4.1.5 Set speed units 1-14

4.1.6 Set offset (set local time) 1-15

4.1.7 Editing settings (overview) 1-16

5.0 Normal operation 1-17

5.1 Modes 1-17

5.1.1 Speed mode 1-18

5.1.2 Speed (Average) mode 1-18

5.1.3 Speed (Maximum) mode 1-19

5.1.4 Odometer mode 1-19

5.1.5 Altitude mode 1-20

5.1.6 Zone mode 1-20

5.1.6.1 Zone (Minimum) 1-21

5.1.6.2 Zone (Maximum) 1-21

5.1.7 Clock mode 1-22

5.1.8 Timer mode 1-23

5.1.9 Timer recall mode 1-23

5.1.10 Mode operation (overview) 1-24

6.0 Restoring default settings 1-25

7.0 Glossary 1-26

8.0 Copyright 1-26

9.0 Additional warnings, disclaimers, and limitations on

liability 1-27

X300

1-6

NAVMAN

1.0 General information

1.1 Checklist

The X300 package should contain the following items:

• Navman X300 GPS Sport.Tool

• Armband

• Quick start guide

• User guide

• 1 x AA battery

1.2 Care and maintenance

Do not attempt to disassemble the X300; there are no user

serviceable components in this product.

The X300 is of robust design. However, care should be taken to

protect from shocks or extreme heat.

Clean using only a soft cloth with mild soap and warm water. Do

not use abrasive cleaning materials or products. We recommend

rinsing the X300 with fresh water after any exposure to salt

water.

CAUTION: Please ensure battery cover is in place during

cleaning.

Store the X300 away from direct sunlight or extreme heat

sources. (Remove battery before storing for an extended

period.)

1.3 Water resistance

The Navman X300 GPS Sport.Tool is water resistant.

1.4 Altitude measurement

Due to the nature of GPS, inaccurate altitude measurements

can sometimes be observed. Altitude readings should be

viewed as indicative measurements only.

X300 – General information

X300 1-7

NAVMAN X300 - General information

1.5 Changing the battery

Always shut down the X300 before changing the battery.

Note: All system settings, and the calculated data that was stored

at the last controlled shutdown*, are retained when the battery is

removed. This information persists indeﬁnitely until updated or reset.

If battery power becomes low during operation the battery icon

is displayed.

For best performance:

General use = Alkaline

Below 5 oC = NiMH

constant = low power

ﬂashing = approx. 5 min before automatic shutdown**

* Press and hold to perform a controlled shutdown.

** When battery power becomes too low to continue operation,

a controlled shutdown is automatically executed (current data

is saved).

battery icon

1. Turn D-ring anti-clockwise and slide enclosure cover down to

open battery enclosure.

2. Insert battery with «» end as indicated inside enclosure.

3. Replace enclosure cover (ensuring lugs at the bottom of the

cover are aligned with slots in the enclosure surround), turn

D-ring clockwise to seal.

X300

1-8

NAVMAN

2.1 Button functions

There are two control buttons, and . These buttons are

pressed separately or together to turn the unit on and off, cycle

through modes, and select mode options.

Throughout this guide the button icons are used as follows:

= press this button

= press both buttons together

Note: where it is required to press and HOLD buttons, a countdown

begins. To perform the required action continue to hold until the

counter reaches zero; if you release the button sooner the action will

not be performed.

2.2 Display screen

The illustration above shows the complete display capability of the X300.

Only a sub-set of these elements appear at any time during operation.

The upper screen section displays the antenna and battery

icons, as well as all values and units. The lower screen

section displays the mode icons and the setup icon (SYSTEM

SET).

Mode Icons

2.0 Navman X300 interface

RCL

AVG

MAX

X300 - Interface

Clock

Timer

Timer recall

Speed

Speed (Average)

Speed (Maximum)

Odometer

Altitude

Zone Set

8 7 2

ZONE

SET

SYSTEM

SET

TOTAL

m kmmi PM mft

MAXMIN

LAP

km/hmph

RCL MAX

AVG

ZONE

SET

X300 1-9

NAVMAN X300 - Getting started

3.1 Be outdoors

The X300 is not intended for operation indoors or under water

as it uses Global Positioning System (GPS) satellites to get

time and date information, and to calculate distance and

speed. For best results, always use the X300 outdoors with an

unobstructed view of the sky.

3.2 Fit the X300

The X300 is designed to be worn on the left upper arm. The

easiest way to ﬁt the unit is to feed the strap through the

fastener to create a loose enclosure. Then slide your left arm

through the enclosure and tighten the strap after the unit is in a

comfortable position.

3.3 Startup

Press and hold to turn the power on and enter setup, OR

press to turn the power on and start normal operation.

First start may take up to 80 seconds to get all the satellite data

Flashing = seeking GPS data

Constant = GPS data obtained

3.0 Getting started

!Always enter setup ﬁrst if you wish to change settings.

To enter setup after starting normal operation, you will

need to shut down and re-start the unit.

�

X300

1-10

NAVMAN

X300 - Getting started

3.3.1 Enter setup

To enter setup

Press and hold to turn the power on and enter setup.

When the counter reaches zero, the X300 will enter setup. If

you release before the counter reaches zero the X300 will

immediately start normal operation.

Note: To enter setup after starting normal operation you will need to

restart the X300. For details about changing settings see Section 4.0.

To leave setup

Press and hold to leave setup and start normal operation.

When the counter reaches zero, the X300 will leave setup and

start normal operation in Speed mode. If you release before

the counter reaches zero the X300 will remain in setup.

Note: you must leave setup ﬁrst if you want to turn the power off.

3.3.2 Start normal operation

To start normal operation

Press to turn the power on and start normal operation.

When starting directly into normal operation, the X300 will start

in the mode it was in at last shutdown. (Speed mode is always

displayed ﬁrst when starting normal operation after leaving

setup.) For details about normal operating modes see Section

5.0.

counter

X300 1-11

NAVMAN

4.1 Setting options

Press and hold to turn the power on and enter setup.

Press repeatedly to step through the setting options.

Setting options are accessed in the order shown below. See

subsequent sections for details about editing settings.

Set (12hr)

lets you set 12hr or 24hr time format

Set (31-12)

lets you set dd-mm or mm-dd date format

Calc up

lets you set the X300 to calculate data for all movement (uphill

and downhill) or for downhill movement only

Beep

When beep is ON a beep will sound when the buttons are

pushed.

Set units (km/h)

lets you set the speed units to km/h or mph

Set offset (set local time)

lets you adjust the X300 to display local time

Press and hold to leave setup and start normal operation.

X300 - Setup

Set (12hr) Calc Up

BeepSet offset

Set (31-12)

Set units (km/h)

4.0 Setup

X300

1-12

NAVMAN

X300 - Setup

4.1.1 Set time format

Set 12hr or 24hr time display format.

To access this option

If necessary, press and hold to turn the power on and enter

setup. Press repeatedly until the screen appears as shown

above.

To set time format

1) Press to start editing (time format option ﬂashes).

2) Press or to select 12hr or 24hr.

3) Press to stop editing.

4) Press to go to the next option, or hold to leave setup.

4.1.2 Set date format

Set ‘dd-mm’ or ‘mm-dd’ date display format.

To access this option

If necessary, press and hold to turn the power on and enter

setup. Press repeatedly until the screen appears as shown

above.

To set the date format

1) Press to start editing (date format example ﬂashes).

2) Press or to select dd-mm or mm-dd.

3) Press to stop editing.

4) Press to go to the next option, or hold to leave setup.

time format

date format

SYSTEM

SET

SYSTEM

SET

X300 1-13

NAVMAN

4.1.3 Calc up

This option lets you choose to monitor and record information

for all movement (uphill and downhill), or for downhill movement

only.

When uphill calculation is ON, all information displayed by the

Navman X300 is based on uphill and downhill movement; laps

must be entered manually.

When uphill calculation is OFF, all information displayed is

based on downhill movement only; laps are automatically

entered if uphill movement is detected after downhill movement.

Additionally, laps may be entered manually. For example, a skier

may wish to enter multiple laps at certain markers on a single

downhill run.

Access this option

If necessary, press and hold to turn the power on and enter

setup. Press repeatedly until the screen appears as shown

above.

To set the Calc up status

1) Press to start editing (status ﬂashes).

2) Press or to select ON or OFF.

3) Press to stop editing.

4) Press to go to the next option, or hold to leave setup.

X300 - Setup

status

SYSTEM

SET

X300

1-14

NAVMAN

4.1.4 Beep

Set beep ON or beep OFF. When beep is ON, an audible ‘beep’

will sound when buttons are pressed.

Access this option

If necessary, press and hold to turn the power on and enter

setup. Press repeatedly until the screen appears as shown

above.

To set button beep status

1) Press to start editing (setting status ﬂashes).

2) Press or to select On or OFF.

3) Press to stop editing.

4) Press to go to the next option, or hold to leave setup.

4.1.5 Set speed units

Set units for speed (km/h or mph).

Access this option

If necessary, press and hold to turn the power on and enter

setup. Press repeatedly until the screen appears as shown

above.

To set speed units

1) Press to start editing (speed units ﬂash).

2) Press or to select km/h or mph.

3) Press to stop editing.

4) Press to go to the next option, or hold to leave setup.

Note: Distance and altitude are displayed in units that correspond

to user selected speed units. For example, if you select speed units

‘km/h’, then distance is displayed in ‘km’ and altitude in ‘m’.

X300 - Setup

speed units

status

SYSTEM

SET

SYSTEM

SET

km mkm/h

X300 1-15

NAVMAN X300 - Setup

4.1.6 Set offset (set local time)

This option lets you adjust the X300 to display local time*. You

only need to do this once, unless operating the unit in a new

time zone.

(* By default the X300 displays GPS time. The X300 will perform

all functions accurately without adjusting the offset to display

your local time.)

Note: If you attempt to change the time offset before all GPS data are

obtained, the screen displays ‘no GPS’ and the antenna icon ﬂashes until all

GPS data are received.

Access this option

If necessary, press and hold to turn the power on and enter

setup. Press repeatedly until the screen appears as shown

above.

To set local time

1) Press to start editing (the screen now appears as shown

below). The current time value ﬂashes. The date is displayed

to ensure that adjustments are made in the correct direction.

2) Press repeatedly to set time display forward (press and

hold to set time display forward quickly), or press

repeatedly to set time display backward (press and hold to

set time display backward quickly**).

3) Press to stop editing.

4) Press to go to the next option, or hold to exit setup.

** While editing is active, holding will not exit setup.

current datecurrent time

SYSTEM

SET

SYSTEM

SET

X300

1-16

NAVMAN

4.1.7 Editing settings (overview)

X300 - Setup

KEY

= press this button

= press both buttons together

settings editing details

beep beep

beep ON

beep OFF

set units (km/h)

set units (mph)

set units (km/h)

set offset

set 12hr

set 31-12

set 24hr

set 12-31

set units (km/h)

set (12hr) set (12hr)

set (31-12)set (31-12)

time (date)

calc up

calc up ON

calc up OFF

calc up

edit accept

�

edit accept

X300 1-17

NAVMAN

5.1 Modes

Press to turn the power on and start normal operation.

Press repeatedly to step through the modes (press and hold

to cycle through the modes quickly).

Modes are accessed in the order shown below. See subsequent

sections for details about using different modes.

Speed mode

shows distance and speed

Speed (AVG) mode

shows distance and average speed

Speed (MAX) mode

shows distance and maximum speed

Odometer mode

shows total distance from last odometer reset

Altitude mode

shows total accumulated altitude and current altitude

Zones

lets you turn zones ON or OFF

When Zone is ON you can set minimum and maximum target speeds (Zone

MIN and Zone MAX).

Clock mode

shows current time and date

GPS time is displayed unless you set local time, see Section 4.1.6.

Timer mode

shows session* and lap* times

Timer recall mode

recalls stored session and lap times

(*See glossary.)

X300 - Normal operation

5.0 Normal operation

Speed Speed AVG Speed MAX Odometer Altitude

ClockTimer

Timer RCL

MAX

AVG

RCL

Zone OFF

Zone ON

Zone MINZone MAX

ZONE

SET

X300

1-18

NAVMAN

5.1.1 Speed mode

This mode lets you monitor session distance and current speed.

To access this mode

If necessary, press to turn the power on and start normal

operation. Press repeatedly until the screen appears as

shown above.

While in Speed mode

• Press to store current lap data (the screen brieﬂy shows the

lap distance, lap number, and lap time that is being stored).

• Press and hold to clear all* session data. (*Does not clear

odometer.)

• Press to go to the next mode.

5.1.2 Speed (Average) mode

This mode lets you monitor session distance and average

speed.

To access this mode

If necessary, press to turn the power on and start normal

operation. Press repeatedly until the screen appears as

shown above.

While in Speed (Average) mode

• Press to store current lap data (the screen brieﬂy shows the

lap distance, lap number, and lap time that is being stored).

• Press and hold to clear all* session data. (*Does not clear

odometer.)

• Press to go to the next mode.

X300 - Normal operation

km km/h

current speed

session distance

AVG

km km/h

average speed

session distance

X300 1-19

NAVMAN

5.1.3 Speed (Maximum) mode

This mode lets you monitor session distance and maximum

speed.

Access this mode

If necessary, press to turn the power on and start normal

operation. Press repeatedly until the screen appears as

shown above.

While in Speed (Maximum) mode

• Press to store current lap data (the screen brieﬂy shows the

lap distance, lap number, and lap time that is being stored).

• Press and hold to clear maximum speed only.

• Press to go to the next mode.

5.1.4 Odometer mode

This mode shows total distance since odometer was last reset.

Access this mode

If necessary, press to turn the power on and start normal

operation. Press repeatedly until the screen appears as

shown above.

While in Odometer mode

• Press to store current lap data (the screen brieﬂy shows the

lap distance, lap number, and lap time that is being stored).

• Press and hold to clear odometer only.

• Press to go to the next mode.

Note: The X300 displays distance in units corresponding to speed

units (see section 4.1.5).

X300 - Normal operation

MAX

km km/h

maximum speed

session distance

total distance

X300

1-20

NAVMAN

5.1.5 Altitude mode

This mode shows total accumulated altitude and the current

altitude.

Access this mode

If necessary, press to turn the power on and start normal

operation. Press repeatedly until the screen appears as

shown above.

While in Altitude mode

• Press to store current lap data (the screen brieﬂy shows the

lap distance, lap number, and lap time that is being stored).

• Press and hold to clear accumulated altitude only.

• Press to go to the next mode.

Note: The Navman X300 displays altitude in units corresponding to

speed units (see section 4.1.5).

5.1.6 Zone mode

When Zone is OFF, the Zone (MIN) and Zone (MAX) options are

skipped and zone alerts do not sound.

Access this mode

If necessary, press to turn the power on and start normal

operation. Press repeatedly until the screen appears as

shown above.

To set Zone status

1) Press to start editing (zone status ﬂashes).

2) Press or to select ON or OFF.

3) Press to stop editing.

4) Press to go to the next mode.

X300 - Normal operation

accumulated altitude current altitude

status

ZONE

SET

Page is loading ...

Navman X300 Owner's manual

Navman X300 Owner's manual

Navman X300 Owner's manual

Related papers

Other documents