GVS K-BUS AMRW-24/10.1 User manual

Brand: GVS

Model: K-BUS AMRW-24/10.1

Type: User manual

Guangzhou Video-star Electronics Industrial Co., Ltd

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

K-BUS○

RSwitch Blind Actuator

User Manual-Ver. 1.2

AMRW-24/10.1

KNX/EIB Intelligent Installation Systems

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

User manual update instructions：

Ver.

Date

Edit contents

Edit position

1.0

2017.1.4

Published the first edition

1.1

2017.4.11

1. Add function of the parameter

“When blind is under end position,

up/down object function is”

Chapter 4.4.1 page 29

1.2

2017.5.25

Add connection diagram of blind

Chapter 3.2 page 8

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

Contents

1. General--------------------------------------------------------------------------------------------------------------------------------------4

2. Technical Data---------------------------------------------------------------------------------------------------------------------------- 6

3. Dimension and Connection Diagram------------------------------------------------------------------------------------------------7

3.1 Dimension diagram------------------------------------------------------------------------------------------------------------------- 7

3.2 Connection diagram------------------------------------------------------------------------------------------------------------------ 8

4. Parameter setting description in ETS--------------------------------------------------------------------------------------------- 10

4.1 Parameter window “General”----------------------------------------------------------------------------------------------------- 10

4.2 Parameter window “Channel function”----------------------------------------------------------------------------------------- 12

4.3 Switch outputs (A~L)---------------------------------------------------------------------------------------------------------------13

4.3.1 Parameter window “Channel X1,2”----------------------------------------------------------------------------------------- 13

4.3.2 Parameter window “X1,2: Time”-------------------------------------------------------------------------------------------- 17

4.3.2.1 Selection “Delay”------------------------------------------------------------------------------------------------------------------- 18

4.3.2.2 Selection “Flashing”----------------------------------------------------------------------------------------------------------------19

4.3.2.3 Selection “Staircase”--------------------------------------------------------------------------------------------------------------- 20

4.3.3 Parameter window “X1,2: Logic”--------------------------------------------------------------------------------------------21

4.3.4 Parameter window “X1,2: Scene”--------------------------------------------------------------------------------------------24

4.3.5 Parameter window “X1,2：Forced"----------------------------------------------------------------------------------------- 25

4.3.6 Parameter window “X1,2：Operation hours counter”------------------------------------------------------------------- 26

4.4 Shutter outputs (A~L)-------------------------------------------------------------------------------------------------------------- 27

4.4.1 Parameter window “Channel X: Shutter”--------------------------------------------------------------------------------- 27

4.4.1.1 Parameter window “X: Drive”---------------------------------------------------------------------------------------------------- 31

4.4.1.2 Parameter window “X: Auto.”---------------------------------------------------------------------------------------------------- 33

4.4.1.3 Parameter window“X: Scene”-----------------------------------------------------------------------------------------------------37

4.4.1.4 Parameter window “X: Safety”--------------------------------------------------------------------------------------------------- 38

4.4.2 Parameter window “Channel X: Blind”----------------------------------------------------------------------------------- 40

5. Communication Objects Description---------------------------------------------------------------------------------------------- 41

5.1 Communication objects of Switch outputs--------------------------------------------------------------------------------------41

5.2 Communication objects of Shutter outputs------------------------------------------------------------------------------------- 44

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

1. General

The Switch Blind actuator is a multi-output module, providing 24 channels switch outputs or 12 channels

curtains outputs, you can configure the functions of the module according to your requirement, such as some

channels are used as switch outputs, other channels are used as curtains outputs. The curtain type can be selected

for the blind and the shutter, the curtain control motor type can be selected for the AC motor or dry contact motor.

The Switch Blind actuator is a modular installation device for fast installation in the distribution board on 35

mm DIN rails to DIN EN 60 715. The electrical connection is implemented by using screw terminals . The

connection to the KNX/EIB bus is implemented using the supplied bus connection terminal, with the system

power input of 21-30V DC. Only bus power supply are required.

This manual provides detailed technical information about the Switch Blind actuator for users as well as

assembly and programming details, and explains how to use the Switch Blind actuator by the application

examples.

The function of the Switch Blind actuator is summarized as follows:

——Switch output, which can connect some electrical loads, such as lighting, sockets. There are 24 outputs,

the power of the load is 230V AC 10A output with manual button controlling in front of the device. The module

offers the following functions:

Switch

Time function: on/off delay

Time function: flashing switch, for lamps of aging test

Time function: staircase lighting, for switch on the staircase lighting and after the duration time the

lighting can be turned off automatically. It is better if the function is used together with motion

detector.

Provide 8 scenes, recall and storing via a 1byte object

Logic operation: AND, OR, XOR, GATE function, up to three logic inputs

Status response, for know the current output state in the visualization

Forced operation, two data types: 1bit/2bit, for force action on or off, with the highest priority

Set the relay contact position after bus voltage recovery

Set the relay contact position after bus voltage failure

Manual switch outputs

Operation hours counter

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

——Shutter output, which can connect with motor blinds, awnings, roller blinds, vertical blind, etc. There are

12 outputs with 230V AC 1000W motor or dry contact controlling motor. The output contacts for the directions UP

and DOWN. The pause on change in direction can be set via the parameters. One output can be also used as 2

channels switch when they are not used as shutter/blind output . The shutter/blind output offers the following

functions:

Movement UP/DOWN

Stop/Louvre adjustment

Move to position 0……100%

Adjustment louvre to position 0……100%(only “Shutter” working mode)

Set 8 scenes, store or recall via a 1byte object

Automatic sun protection

Safety function

Status response, query and reply the current shutter/blind position and operation mode to the bus,

thereby indicating the status in the visualization device

Two working mode: Blind and Shutter

Programmers are able to use the Engineering Tool Software ETS (ETS4 version or above) with a .knxprod file

to allocate the physical address and set the parameters.

To make sure that all the programmable functions are used correctly, you must check the connection of the

loads before use and note technical characteristic of loading equipment, particularly shutter driver, they refer more

technical characteristics, some characteristics are inherent, if not properly set them, it is likely to cause the load

device damage or not operating correctly.

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

2. Technical Data

Power Supply

Bus Voltage，EIB

21~30V DC, from EIB bus

Current consumption, EIB

<12mA

Power consumption, EIB

<360mW

Power consumption 10A

<1W

Capacitor charge current

Max. 24mA

Output

24 channels

Can be individually set (including switch, shutter )

Unrated voltage

230/400V AC（50/60Hz）

Inrated current capacity

10A/105uF

Max. switching current

16A/240V AC

Mechanical endurance

> 2 x 106

Electrical endurance

>5 x104

Max. DC current switching

capacity (resistive load)

16A/30V DC

Connection

EIB/KNX

Via bus connection terminals（red/black），Ø0.8 mm

Outputs A/B/C1

Screw terminals

Wire Range0.5-4mm2

Torque 0.8N-m

Other outputs

Screw terminals

Wire Range 0.5-2.5mm2

Torque0.5N-m

Operation/

display

Programming button/ red LED

For assignment of the physical address

Green LED flashing

The application layer works normally

Temperature

range

Operation

-5℃……+45℃

Storage

-25℃……+55℃

Transport

-25℃……+70℃

Ambient

conditions

Max. air humidity

<93%，except dewing

Design

Modular installation device (MDRC)

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

Housing/color

Plastic housing, gray

Installation

On 35mm DIN-Rail

To EN 60 715

Dimension

216mm ×90 mm ×64mm

Weight

0.8KG

Note: The above load is only for single lamps. In the case of several lamps in parallel, the load will be

reduced, although the power is unchanged, but the instantaneous impact of current will increase, and easy to

make the relay contacts melted. So, in normal use, subject to the measured current, the measured maximum

inrush current must be within the allowable range.

Application program：

Model

Max. number of

communication objects

Max. number of group

addresses

Max. number of

associations

AMRW-24/10.1

212

254

3. Dimension and Connection Diagram

3.1Dimension diagram

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

3.2 Connection diagram

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

①③ Output terminals A~L, such as A1,A2 of them can be as two channel switch outputs or one channel curtain output. As curtain

output, A1 corresponds to A↑, A2 corresponds to A↓. The other channels have the same usage.

②Manual operation buttons and status indicating light for outputs A~L, manual/auto. operation (Man.)switch button and status

indicating light.

Manual/Auto. switch button (Man.):

Switch the manual/Auto. Operation via a long operation. In the manual operation, switch the output channels via a short

operation.

When the indicator LED near the button is RED(R), the output of operation buttons can be used to control A,B,C,D.

When the indicator LED is GREEN(G), the output of operation buttons can be used to control E,F,G,H.

When the indicator LED is R&G, the output of operation buttons can be used to control I,J,K,L.

The output of operation button:

When control switch output via the button, the indicator LED near the button indicates the output state, the LED on is

output, off is no output.

When control curtain output, to move up/down the curtain via a long operation, and slat adj./stop via a short operation.

When curtain is running, the indicator LED will flash; If both of blinds and slat arrive at minimum or maximum position,

the LED will be on.

Note: The manual operation is set via the parameter “Manual operation” in window “General”. If disable, these buttons and LED are

not work.

④EIB/KNX bus terminal

⑤Programming button and LED: Red LED indicates physical address programming; Green LED indicates the normal working of

application layer.

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

4. Parameter setting description in ETS

The parameters will be described in the form of the function interfaces.

4.1 Parameter window “General”

Parameter window “General” can be shown in fig.4.1. Here set some general parameters, that applies to the

curtain output, also applies to the switch output.

Fig. 4.1 Parameter Window “General”

Parameter “Operation delay after power voltage recovery [5…250s]”

The parameter defined the delay time that scan and relay operation after bus voltage recovery. No operation

will be executed before the scan and relay operation delay finished, the operation during this process will be

recorded and executed after the delay over. Meanwhile, telegrams sent during the scan delay will be recorded and

executed after the delay.

The delay time here does not include the initiation time of the device, normally it will take 3 seconds to

re-initiate the device after power voltage recovery. I.e the delay will start counter after the initiation time.

Note: During delay, the programming LED is on green , and the device can not be operated. After delay over,

the LED will flash green, and the device can be operated.

Parameter “Sending cycle of ‘in operation’ telegram (1...240s, 0 = inactive):”

The parameter determines the time interval to send the telegram which shows the actuator is working normally

or not via the bus. With the setting “0”, the actuator doesn’t send the telegram; if the setting is not “0”, a telegram

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

with the value “1” will be sent cyclically according to the setting to the bus.

Options: 0…240s, 0=cyclical send inactive

It is suggested to select the maximum time interval according to the application to keep the bus load as low as

possible.

Note: it is starting to count the time after power up, instead of the operation delay after recovery of bus

voltage.

Parameter “Limit number of send telegram”

This parameter is used to set the number limit of sending telegrams sent to the bus in order to decrease the load

of bus, options：

Yes

When select “Yes”, the parameter “Period” and “Max. Number of send telegram within a period[1…255]” will

be visible.

Parameter “Period”

This is to set the limit time of sending telegrams. Options:：

100ms

500ms

……

10min

After bus voltage recovery, when the initialization time and the scan and relay operation delay have been

completed, the set period begins and counting the telegrams also begins. Once the max. number of telegrams has

reached during the set period, the device will not send telegram to the bus until the next set period start, and the

telegrams that have not been sent will be stored in buffer and send in the next set period. The buffer can store up to

20 telegrams, if there are repetitive telegrams, the telegrams will be only sent once in the next set period.

Parameter “Max. Number telegram within a period[1…255]”

This is to set the Max. number of telegrams being sent within the setting monitored period.

Option: 1…255

Note: the above two parameters only affect the telegrams sent to the bus, they don’t affect the operation

action.

Parameter “Central control for switch function”

This parameter sets the central control for switch function. Options:

Disable

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

Enable

If enable，the object“Central control for all of switch”is visible，all channels with central control enabled can

be switched together via the object.

Parameter “Manual operation”

The parameter defines whether the manual operation enables. Options：

Disable

Enable

If the enable is selected, the Man. /Auto Button has been enabled. And the follow parameter is visible.

Parameter “Manual to automatic by”

Options:

Only long press

Both long press and automatic delay time

If set “only long press, the manual/auto”. Operation only can be switched via long press the Man. Button.

If set “both long press and automatic delay time”, the manual/auto. Operation can be switched via long press

the Man. Button. or the set time for the manual to automatic has elapsed.

Parameter “Delay time *1s[10...60000]”

The parameter appears when “both long press and automatic delay time” is selected in the parameter “manual

to automatic by”. It is used for setting the time for an automatic reset from the “manual operation” to “automatic

operation” state after the last push button operation.

Options: 10……60000s

Note: The operation buttons that are located at the front of the device is invalid in the safety functions.

4.2 Parameter window “Channel function”

Parameter window “Channel function” can be shown in fig.4.2. Here set channel function, as switch outputs or

curtain output, one channel can be used as two switch outputs or a curtain output. Whether it is switch output or

curtain output, Each switch or curtain output can be set separately, and parameters and objects which are assigned to

each output are the same. The follow using a output as an example described the switch output and curtain output.

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

Fig. 4.2 Parameter Window“Channel function”

When the channel is enabled, the corresponding parameters can be set.

4.3 Switch outputs (A~L)

There are max. 24 outputs. Each output can be set separately, and parameters and objects which are assigned to

each output are the same. Using output A1 as an example described.

4.3.1 Parameter window “Channel X1,2”

Parameter window “Channel X1,2” can be shown in fig.4.3. which applies to a whole output. In addition to

setting general switching function, but also set position of switch on the bus power on and power down , reports of

switch status, etc..

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

Fig. 4.3 parameter window “Channel X1,2”

Parameter “Central control of channel”

The parameter sets whether the central control of the channel is enabled. Options：

Disable

Enable

If enable，the channel can be controlled via the object “Central control for all of switch”.

Parameter “If bus recovery，contact is”

The output can adopt a defined status on bus voltage recovery via this parameter. Options:

unchange

Open

Closed

As before as bus fail

When selecting “Unchanged”, the contact of the relay will remain the same as the last status on the power on.

When selecting “open”, the contact will be open; while it is closed when selecting “closed”.

The contact position after voltage recovery is the same as that before power off with “As before bus voltage

fail”.

Parameter “If bus fail, contact is”

The output can adopt a defined status after the bus voltage failure via this parameter. Options:

Unchange

open

closed

When selecting “Unchange”, the contact of the relay will remain the same as the last status before power off;

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

when selecting “open”, the contact will be open; while it is closed when selecting “closed”.

Parameter “After downloading, contact is”

This parameter set the contact position of the output after downloading. Options:

Open

As bus recovery

If “open”, the output is open after downloading.

If “As bus recovery”, the output adopts the defined status of the parameter “If bus recovery, contact is”

Parameter "Object Value of “Switch”after bus recovery”

This parameter will be used when enabling the logic function “input 0” to define the default value of the

communication object “Switch” after bus voltage recovery, which can be “0” or “1”. Options:

Parameter “Set the reply mode of switch status”

This parameter defines how to respond the current switch status to the bus. There are three options to select.

Options:

Respond after read only

respond after change

respond always

If selecting “respond after read only”, the status telegram will not be sent out until receiving a read request

telegrams via the object “reply switch status” from the bus.

If selecting “respond after change”, it will send the status immediately via the object “reply switch status”

when there are any changes on the output.

If selecting “respond always”, no matter it’s reading, or there is change for the status, as long as the controlling

telegram can be received, the object will send the current status to the BUS.

Parameter "Object value of switch status :”

Options:

0=contact close; 1=contact open

0=contact open; 1=contact close

It means the contact of the relay will be closed when the value of the communication object “reply switch

status”is 0 when setting “0=contact close; 1=contact open”, while it is open when the value is “1”.

It means the opposite with setting “0=contact open; 1=contact close”.

Parameter “Contact position if tele. Value is ‘1’(‘0’is opposite of ‘1’if changed) ”

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

This parameter defines the contact position when switch on the switch, which will be triggered by the

communication object “switch, X”. When enabling “input 0” in the logic function, it will use the communication

object “switch, X” to modify the value of “input 0”, rather than triggering the switch operation. In this case, this

parameter is no significance to the switch. Options:

Open

The parameter only works after the object “Switch x” receiving value, and defines the direction of the contact

after receiving it. The details can be found in the below form:

Parameter options

“Switch, X” object value =1

“Switch, X” object value =0

Open

Contact open(OFF)

Contact close (ON)

Contact open (OFF)

Since the switch and logic functions share the same object “switch, X”, thus need to understand the

relationship between them, the control sequence shown below (the logic functions, please refer to the

following chapter describe):

Object “Switch, X”

Object “Input 1 of logic, X”

Object “Input 2 of logic, X”

Output（Relay to perform an action）

Fig. 4.4 switch and logical function diagram

Switch function

Is logic “Input 0”enable?

Logic

function

Result

“switch” object value

Yes

“switch” object value

AND, OR, XOR,

GATE

AND, OR, XOR,

GATE

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

When the logic function “input 0” enables, the object “switch, X” used as input of “input 0”, the operation

of general switch will become invalid.

Parameter “Special functions of switch actuator mode”

This parameter defines whether enable the special functions of the switch actuator. The parameter window

“X1,2: Function” will be seen with “enable”, and able to set the special functions individually in Fig. 4.5. Enable or

disable the special function in “X1,2: Function”.

Options:

Disable

Enable

Fig. 4.5 the special function enable window “X1,2: Function”

4.3.2 Parameter window “X1,2: Time”

This parameter window will become visible when selecting “enable” in the parameter “Function of “time” ”

in the window “X:Function” shown in Fig. 4.5. See Fig. 4.6. And the object “enable time function” will be also

visible, which is used to disable the time function. After disabled, previous operation is still carried out completely.

Such as delay switch on, the function is disabled during delay, and then the switch is still switched on once the

delay has been finished.

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

Fig. 4.6 parameter window “X1,2: Time-Delay ”

Parameter “Type of time function”

The parameter defines the type of the time function, there are three options for the mode of work. Options：

Delay

Flashing

Staircase

4.3.2.1 Selection “Delay”

The parameter window of the delay switch in Fig. 4.6 will be shown when selecting “Delay”. The delay switch

can be started via the object “Delay function”.

Parameter “Delay for switch on: (0...240 min)/ (0...59 s)”

This parameter defines the delay time of switching on.

Options:

0…240 min

0…59s

After receiving the delay ON telegram, the switch is on once the delay over.

Parameter “Delay for switch off: (0...240 min) / (0...59 s)”

This parameter defines the delay time of switching off.

Options:

0…240 min

0…59 s

After receiving the delay off telegram, the switch is off once the delay over.

If receiving the relevant telegram again during delay, the delay will be reset.

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

4.3.2.2 Selection “Flashing”

The parameter window in Fig. 4.7 “X: Time-flashing” will be shown up when selecting “flashing” in the

parameter “Type of time function”. The flashing switch function is mainly used for lamp aging test.

Fig. 4.7 parameter window “X1,2: Time-flashing”

The flashing switch can be started via the object “Flashing function”. It is able to set the flashing time in

“Delay for switch on” or “Delay for switch off”, which will restart the flashing when receiving the start flashing

telegram, and define the contact position after flashing.

Parameter “Delay for switch on: (0...240Min), (0...59s)”

The parameter defines the duration time of switch on the output when flashing.

Options:

0...240 min

0...59 s

Note: it will not be executed unless the time is lower than the relay threshold switch frequency. Since there

will be not sufficient energy to do it because of the frequent relay switching, and it may cause the time delay. The

same situation will happen after the bus voltage recovery.

Parameter “Delay for switch off: (0...240Min), (0...59s)”

The parameter defines the duration time of switch off the output when flashing. Options:

0...240 min

0...59 s

Note: it will not be executed unless the time is lower than the relay threshold switch frequency. Since there

will be not sufficient energy to do it because of the frequent relay switching, and it may cause the time delay. The

same situation will happen after the bus voltage recovery.

Parameter “Number of ON-impulses (1...255，0=no limited)”

K-BUS○

RKNX/EIB Switch Blind Actuator

www.video-star.com.cn marketing@video-star.com.cn Tel.：（8620）39338986

Fax：（8620）39338465

This parameter sets the flashing times.0 means no limited. A flashing includes an on and an off actions.

Options:0...255

Parameter “Contact position after flashing”

This parameter defines the relay contact position after flashing. Options:

Unchanged

Open

Parameter“Control mode of flashing”

The parameter is used to select the control mode of the flashing output. Options:

Start with“1”, stop with “0”

Start with “0”, stop with “1”

Startwith “1/0”, can not be stopped

It will start flashing with value “1” when selecting “star with “1”, stop with “0” ”; it will stop flashing with “0”.

The stop position is defined via last parameter.

It will start flashing with value “0” when selecting “star with “0”, stop with “1” ”; it will stop flashing with “1”.

The stop position is defined via last parameter.

It will start flashing with either “1” or “0” when selecting “star with “1/0”, can not be stopped”; Under this

circumstance it cannot terminate the flashing by value until operation over or it is blocked by other operation.

4.3.2.3 Selection “Staircase”

The parameter window of the staircase lighting function in Fig. 4.8 will be visible when selecting “Staircase”

in the parameter “Type of time function”.

Fig. 4.8 parameter window “X1,2: Time-staircase”

The staircase lighting can be started via the object “staircase function”. The value that switches on the staircase

Page is loading ...

GVS K-BUS AMRW-24/10.1 User manual

GVS K-BUS AMRW-24/10.1 User manual

GVS K-BUS AMRW-24/10.1 User manual

Related papers

Other documents