H3C S5510 Series Operating instructions

Brand: H3C

Model: S5510 Series

Type: Operating instructions

This manual is also suitable for

S3610 Series

The H3C S5510 Series, a high-performance and scalable switch, delivers a comprehensive suite of features to empower your network. With Layer 3 routing capabilities, it enables efficient data forwarding and routing between VLANs and supports up to 256 static routes. The S5510 Series safeguards your network with robust security features like IP Source Guard, which protects against IP address spoofing, and comprehensive ACLs, ensuring only authorized traffic traverses your network.

Operation Manual – IP Source Guard

H3C S3610&S5510 Series Ethernet Switches Table of Contents

Table of Contents

Chapter 1 IP Source Guard Configuration..................................................................................1-1

1.1 IP Source Guard Overview................................................................................................1-1

1.2 Configuring a Static Binding Entry.....................................................................................1-1

1.3 Configuring Port Filtering...................................................................................................1-2

1.4 Displaying IP Source Guard ..............................................................................................1-2

1.5 IP Source Guard Configuration Examples.........................................................................1-3

1.5.1 Static Binding Entry Configuration Example...........................................................1-3

1.5.2 Port Filtering Configuration Example...................................................................... 1-5

1.6 Troubleshooting.................................................................................................................1-6

1.6.1 Failed to Configure Static Binding Entries and Port Filtering..................................1-6

Operation Manual – IP Source Guard

H3C S3610&S5510 Series Ethernet Switches Chapter 1 IP Source Guard Configuration

1-1

Chapter 1 IP Source Guard Configuration

When configuring IP Source Guard, go to these sections for information you are

interested in:

z IP Source Guard Overview

z Configuring a Static Binding Entry

z Configuring Port Filtering

z Displaying IP Source Guard

z IP Source Guard Configuration Examples

z Troubleshooting

1.1 IP Source Guard Overview

By filtering packets on a per-port basis, IP source guard prevents packets with illegal IP

addresses and MAC addresses from traveling through, improving the network security.

IP source guard filters packets based on two types of binding entries:

z IP-port binding entry: A port permits packets with source IP addresses among its

IP-port binding entries.

z MAC-IP-port binding entry: A port permits packets with source MAC address and

source IP address pairs among its MAC-IP-port binding entries.

All other packets are denied.

Caution:

IP source guard and aggregation group configuration are mutually exclusive.

1.2 Configuring a Static Binding Entry

Follow these steps to configure a static binding entry:

To do… Use the command… Remarks

Enter system view

system-view

—

Enter interface view

interface interface-type

interface-number

—

Operation Manual – IP Source Guard

H3C S3610&S5510 Series Ethernet Switches Chapter 1 IP Source Guard Configuration

1-2

To do… Use the command… Remarks

Configure a static binding

entry

user-bind ip-address

ip-address

[ mac-address

mac-address

Required

No static binding entry

exists by default.

 Note:

z The system does not support repeatedly binding a binding entry to one port. A

binding entry can be configured to multiple ports

z In a valid binding entry, the MAC address cannot be all 0s, all Fs (a broadcast

address), or a multicast address, and the IP address can only be a Class A, Class B,

or Class C address and can be neither 127.x.x.x nor 0.0.0.0.

1.3 Configuring Port Filtering

Port filtering allows IP source guard to filter packets based on the MAC-IP-port binding

entries created and maintained by DHCP snooping.

Follow these steps to configure port filtering:

To do… Use the command… Remarks

Enter system view

system-view

—

Enter interface view

interface interface-type

interface-number

—

Configure port

filtering

ip check source ip-address

[ mac-address ]

Required

Not configured by default

1.4 Displaying IP Source Guard

To do… Use the command… Remarks

Display information

about static binding

entries

display user-bind [ interface

interface-type interface-number |

ip-address ip-address |

mac-address mac-address ]

Available in any view

Display information

about dynamic

binding entries

display ip check source [ interface

interface-type interface-number |

ip-address ip-address |

mac-address mac-address ]

Available in any view

Operation Manual – IP Source Guard

H3C S3610&S5510 Series Ethernet Switches Chapter 1 IP Source Guard Configuration

1-3

1.5 IP Source Guard Configuration Examples

1.5.1 Static Binding Entry Configuration Example

I. Network requirements

As shown in Figure 1-1, switches A and B and Hosts A, B and C are on an Ethernet.

Host A and Host B are connected to ports Ethernet 1/0/1 and Ethernet 1/0/2 of Switch B

respectively, Host C is connected to port Ethernet 1/0/1 of Switch A, while Switch B is

connected to port Ethernet 1/0/2 of Switch A.

Detailed requirements are as follows:

z On port Ethernet 1/0/2 of Switch A, only IP packets with the source MAC address

of 00-01-02-03-04-05 and the source IP address of 192.168.0.3 can pass.

z On port Ethernet 1/0/1 of Switch A, only IP packets with the source MAC address

of 00-01-02-03-04-06 and the source IP address of 192.168.0.1 can pass.

z On port Ethernet 1/0/1 of Switch B, only IP packets with the source MAC address

of 00-01-02-03-04-06 and the source IP address of 192.168.0.1 can pass.

z On port Ethernet 1/0/2 of Switch B, only IP packets with the source MAC address

of 00-01-02-03-04-07 and the source IP address of 192.168.0.2 can pass.

II. Network diagram

Figure 1-1 Network diagram for configuring static binding entries

III. Configuration procedure

1) Configure Switch A

# Configure the IP addresses of various interfaces (omitted).

# Configure port Ethernet 1/0/2 of Switch A to allow only IP packets with the source

MAC address of 00-01-02-03-04-05 and the source IP address of 192.168.0.3 to pass.

<SwitchA> system-view

Operation Manual – IP Source Guard

H3C S3610&S5510 Series Ethernet Switches Chapter 1 IP Source Guard Configuration

1-4

[SwitchA] interface ethernet 1/0/2

[SwitchA-Ethernet1/0/2] user-bind ip-address 192.168.0.3 mac-address

0001-0203-0405

[SwitchA-Ethernet1/0/2] quit

# Configure port Ethernet 1/0/1 of Switch A to allow only IP packets with the source

MAC address of 00-01-02-03-04-06 and the source IP address of 192.168.0.1 to pass.

[SwitchA] interface ethernet 1/0/1

[SwitchA-Ethernet1/0/1] user-bind ip-address 192.168.0.1 mac-address

0001-0203-0406

2) Configure Switch B

# Configure the IP addresses of various interfaces (omitted).

# Configure port Ethernet 1/0/1 of Switch B to allow only IP packets with the source

MAC address of 00-01-02-03-04-06 and the source IP address of 192.168.0.1 to pass.

<SwitchB> system-view

[SwitchB] interface ethernet 1/0/1

[SwitchB-Ethernet1/0/1] user-bind ip-address 192.168.0.1 mac-address

0001-0203-0406

[SwitchB-Ethernet1/0/1] quit

# Configure port Ethernet 1/0/2 of Switch B to allow only IP packets with the source

MAC address of 00-01-02-03-04-07 and the source IP address of 192.168.0.2 to pass.

[SwitchB] interface ethernet 1/0/2

[SwitchB-Ethernet1/0/2] user-bind ip-address 192.168.0.2 mac-address

0001-0203-0407

3) Verify the configuration

# On Switch A, static binding entries are configured successfully.

<SwitchA> display user-bind

The Following User address bind have been configured:

Mac IP Port Status

0001-0203-0405 192.168.0.3 Ethernet1/0/2 Static

0001-0203-0406 192.168.0.1 Ethernet1/0/1 Static

-------------2 bind entries queried, 2 listed------------

# On Switch B, static binding entries are configured successfully.

<SwitchB> display user-bind

The Following User address bind have been configured:

Mac IP Port Status

0001-0203-0406 192.168.0.1 Ethernet1/0/1 Static

0001-0203-0407 192.168.0.2 Ethernet1/0/2 Static

-------------2 bind entries queried, 2 listed------------

Operation Manual – IP Source Guard

H3C S3610&S5510 Series Ethernet Switches Chapter 1 IP Source Guard Configuration

1-5

1.5.2 Port Filtering Configuration Example

I. Network requirements

Switch A connects to Client A and the DHCP Server through Ethernet 1/0/1 and

Ethernet 1/0/2 respectively. DHCP Snooping is enabled on Switch A.

Detailed requirements are as follows:

z Client A with the MAC address of 00-01-02-03-04-06 obtains an IP address

through the DHCP Server.

z On Switch A, create the DHCP Snooping entry of Client A.

z Enable IP filtering on port Ethernet 1/0/1 of Switch A to prevent attacks from clients

using fake source IP addresses to the DHCP server.

 Note:

For detailed configuration of DHCP Server, refer to DHCP Configuration in this manual.

II. Network diagram

Figure 1-2 Network diagram for configuring port filtering

III. Configuration procedure

1) Configure Switch A

# Configure port filtering on port Ethernet 1/0/1.

<SwitchA> system-view

[SwitchA] interface ethernet1/0/1

[SwitchA-Ethernet1/0/1] ip check source ip-address mac-address

[SwitchA-Ethernet1/0/1] quit

# Enable DHCP snooping on Switch A.

[SwitchA] dhcp-snooping

# Configure port Ethernet 1/0/2 connected to the DHCP server as a trusted port.

[SwitchA] interface ethernet1/0/2

[SwitchA-Ethernet1/0/2] dhcp-snooping trust

[SwitchA-Ethernet1/0/2] quit

2) Verify the configuration

Operation Manual – IP Source Guard

H3C S3610&S5510 Series Ethernet Switches Chapter 1 IP Source Guard Configuration

1-6

# Port filtering is configured successfully on port Ethernet 1/0/1.

[SwitchA] interface ethernet1/0/1

[SwitchA-Ethernet1/0/1] display this

interface Ethernet1/0/1

ip check source ip-address mac-address

return

# Display the dynamic binding entries that port Ethernet 1/0/1 has obtained from DHCP

Snooping.

<SwitchA> display ip check source

The Following User address bind have been configured:

Mac IP Port Status

0001-0203-0406 192.168.0.1 Ethernet 1/0/1 Dynamic

-------------1 bind entries queried, 1 listed------------

# Display the dynamic entries of DHCP Snooping and check it is identical with the

dynamic entries that port Ethernet 1/0/1 has obtained.

<SwitchA> display dhcp-snooping

DHCP Snooping is enabled.

The client binding table for all untrusted ports.

Type : D--Dynamic , S--Static

Type IP Address MAC Address Lease VLAN Interface

==== =============== ============== ============ ==== =================

D 192.168.0.1 0001-0203-0406 86335 1 Ethernet1/0/1

As you see, port Ethernet 1/0/1 has obtained the dynamic entries generated by DHCP

Snooping after it is configured with port filtering.

1.6 Troubleshooting

1.6.1 Failed to Configure Static Binding Entries and Port Filtering

I. Symptom

Configuring static binding entries and port filtering fails on a port.

II. Analysis

IP Source Guard is not supported on the port which has joined an aggregation group.

Neither static binding entries nor port filtering can be configured on the port which has

joined an aggregation group.

III. Solution

Remove the port from the aggregation group.

H3C S5510 Series Operating instructions

Brand: H3C

Model: S5510 Series

Type: Operating instructions

This manual is also suitable for

S3610 Series

Download PDF

report

H3C S5510 Series Operating instructions

This manual is also suitable for

H3C S5510 Series Operating instructions

Related papers

Other documents