Digisol DIGISOL 24/ 48 Port Gigabit Ethernet Access Layer 3 Switch User manual

Category
Software
Type
User manual

This manual is also suitable for

DG-GS4600SE2 Series
GIGA LAYER 3 SWITCHES
Configuration Guide
V1.0
2018-01-30
As our products undergo continuous development the specifications are subject to change without prior notice
DG-GS4600SE2 Configuration Guide
1
Content
CHAPTER 1 SWITCH MANAGEMENT
...............................................
1
1.1 MANAGEMENT OPTIONS..................................................................................1
1.1.1 Out-Of-Band Management.................................................................................1
1.1.2 In-band Management.......................................................................................... 5
1.2 CLI INTERFACE.............................................................................................. 11
1.2.1 Configuration Modes........................................................................................ 11
1.2.2 Configuration Syntax....................................................................................... 14
1.2.3 Shortcut Key Support.......................................................................................15
1.2.4 Help Function..................................................................................................... 16
1.2.5 Input Verification................................................................................................16
1.2.6 Fuzzy Match Support........................................................................................17
CHAPTER 2 BASIC SWITCH CONFIGURATION
.............................
1
2.1 BASIC CONFIGURATION...................................................................................1
2.2 TELNET MANAGEMENT.................................................................................... 2
2.2.1 Telnet....................................................................................................................... 2
2.2.2 SSH.......................................................................................................................... 5
2.3 CONFIGURE SWITCH IP ADDRESSES..............................................................6
2.3.1 Switch IP Addresses Configuration Task List............................................. 7
2.4 SNMP CONFIGURATION..................................................................................8
2.4.1 Introduction to SNMP......................................................................................... 8
2.4.2 Introduction to MIB........................................................................................... 10
2.4.3 Introduction to RMON.......................................................................................11
2.4.4 SNMP Configuration......................................................................................... 11
2.4.5 Typical SNMP Configuration Examples...................................................... 14
2.4.6 SNMP Troubleshooting....................................................................................16
2.5 SWITCH UPGRADE......................................................................................... 17
DG-GS4600SE2 Configuration Guide
2
2.5.1 Switch System Files......................................................................................... 17
2.5.2 BootROM Upgrade............................................................................................ 17
2.5.3 FTP/TFTP Upgrade............................................................................................ 20
CHAPTER 3 FILE SYSTEM OPERATIONS
.......................................
1
3.1 INTRODUCTION TO FILE STORAGE DEVICES...................................................1
3.2 FILE SYSTEM OPERATION CONFIGURATION TASK LIST.................................1
3.3 TYPICAL APPLICATIONS................................................................................... 3
3.4 TROUBLESHOOTING......................................................................................... 3
CHAPTER 4 CLUSTER CONFIGURATION
.......................................
1
4.1 INTRODUCTION TO CLUSTER NETW ORK MANAGEMENT...................................1
4.2 CLUSTER NETWORK MANAGEMENT CONFIGURATION SEQUENCE............... 2
4.3 EXAMPLES OF CLUSTER ADMINISTRATION.....................................................5
4.4 CLUSTER ADMINISTRATION TROUBLESHOOTING............................................6
DG-GS4600SE2 Configuration Guide
Chapter 1-1
Chapter 1 Switch Management
1.1 Management Options
After purchasing the switch, the user needs to configure the switch for network
management. Switch provides two management options: in-band management and
out-of-band management.
1.1.1 Out-Of-Band Manageme nt
Out-of-band management is the management through Console interface. Generally,
the user will use out-of-band management for the initial switch configuration, or when
in-band management is not available. For instance, the user must assign an IP address to
theswitchviatheConsoleinterfacetobeabletoaccesstheswitchthroughTelnet.
The procedures for managing the switch via Console interface are listed below:
Step 1: setting up the environment:
Fig 1- 1 Out-of-band Management Configuration Environment
As shown in above, the serial port (RS-232) is connected to the switch with the serial
cable provided. The table below lists all the devices us ed in the connection.
Device Name Description
PC machine Has functional keyboard and RS-232, with terminal
Connect with serial port
DG-GS4600SE2 Configuration Guide
Chapter 1-2
emulator installed, such as HyperTerminal included in
Windows 9x/NT/2000/XP.
Serial port cable One end attach to the RS-232 serial port, the other end to
the Console port.
Switch Functional Console port required.
Step 2 Entering the HyperTerminal
Open the HyperTerminal included in Windows after the connection established. The
example below is based on the HyperTerminal included in Windows XP.
1) Click Start menu - All Programs -Accessories -Communication - HyperTerminal.
Fig 1- 2 Opening Hyper Terminal
2) Type a name for opening HyperTerminal, such as “Switch”.
DG-GS4600SE2 Configuration Guide
Chapter 1-3
Fig 1- 3 Opening HyperTerminal
3) In the “Connecting using” drop-list, select the RS-232 serial port used by the PC, e.g.
COM1, and click “OK”.
Fig 1- 4 Opening HyperTerminal
4) COM1 property appears, select “115200” for “Baud rate”, 8” for “Data bits”, “none” for
“Parity checksum”, “1” for stop bit and “none” for traffic control; or, you can also click
“Restore default” and click “OK”.
DG-GS4600SE2 Configuration Guide
Chapter 1-4
Fig 1- 5 Opening HyperTerminal
Step 3: Entering switch CLI interface
Power on the switch, the following appears in the HyperTerminal windows, that is the
CLI configuration mode for Switch.
Testing RAM...
0x077C0000 RAM OK
Loading MiniBootROM...
Attaching to file system ...
Loading nos.img ... done.
Booting......
Starting at 0x10000...
Attaching to file system ...
……
--- Performing Power-On Self Tests (POST) ---
DRAM Test....................PASS!
PCI Device 1 Test............PASS!
FLASH Test...................PASS!
FAN Test.....................PASS!
Done All Pass.
DG-GS4600SE2 Configuration Guide
Chapter 1-5
------------------ DONE ---------------------
Current time is SUN JAN 01 00:00:00 2006
……
Switch>
The user can now enter commands to manage the switch. For a detailed description
for the commands, please refer to the following chapters.
1.1.2 In-band Management
In-band management refers to the management by login to the switch using Telnet, or
using HTTP, or using SNMP management software to configure the switch. In-band
management enables management of the switch for some devices attached to the switch.
In the case when in-band management fails due to switch configuration changes,
out-of-band management can be used for configuring and managing the switch.
1.1.2.1 Management via Telnet
To manage the switch with Telnet, the following conditions should be met:
1) Switch has an IPv4/IPv6 address configured;
2) The host IP address (Telnet client) and the s witch’s VLAN interface IPv4/IPv6
address is in the same network segment;
3) If 2) is not met, Telnet client can connect to an IPv4/IPv6 address of the switch via
other devices, such as a router.
The switch is a Layer 3 switch that can be configured with several IPv4/IPv6
addresses, the configuration method refers to the relative chapter. The following example
assumes the shipment status of the switch where only VLAN1 exists in the system.
The following describes the steps for a Telnet client to connect to the switch’s VLAN1
interface by Telnet(IPV4 address example):
DG-GS4600SE2 Configuration Guide
Chapter 1-6
Fig 1- 6 Manage the switch by Telnet
Step 1: Configure the IP addresses for the switch and start the Telnet Server function on
the switch.
First is the configuration of host IP address. This should be within the same network
segment as the switch VLAN1 interface IP address. Suppose the switch VLAN1 interface
IP address is 10.1.128.251/24. Then, a possible host IP address i s 10.1.128.252/24. Run
“ping 10.1.128.251” from the host and verify the result, check for reasons if ping failed.
The IP address configuration commands for VLAN1 interface are listed below. Before
in-band management, the switch must be configured with an IP address by out-of-band
management (i.e. Console mode), the configuration commands are as follows (All switch
configuration prompts are assumed to be “Switch” hereafter if not otherwise specified):
Switch>
Switch>enable
Switch#config
Switch(config)#interface vlan 1
Switch(Config-if-Vlan1)#ip address 10.1.128.251 255.255.255.0
Switch(Config-if-Vlan1)#no shutdown
To enable the Telnet Server function, users should type the CLI command
telnet-server enable in the global mode as below:
Switch>enable
Switch#config
Switch(config)# telnet-server enable
Step 2: Run Telnet Client program.
Connected with cable
DG-GS4600SE2 Configuration Guide
Chapter 1-7
Run Telnet client program included in Windows with the specified Telnet target.
Fig 1- 7 Run telnet client program included in Windows
Step 3: Login to the switch.
Login to the Telnet configuration interface. Valid login name and password are
required, otherwise the switch will reject Telnet access. This is a method to protect the
switch from unauthorized access. As a result, when Telnet is enabled for configuring and
managing the switch, username and password for authorized Telnet users must be
configured with the following command: username <username> privilege <privilege>
[password (0|7) <password>]. To open the local authentication style with the following
command: authentication line vty login local. Privilege option must exist and just is 15.
Assume an authorized user in the switch has a username of “test”, and password of “test”,
the configuration procedure should like the following:
Switch>enable
Switch#config
Switch(config)#username test privilege 15 password 0 test
Switch(config)#authentication line vty login local
Enter valid login name and password in the Telnet configuration interface, Telnet user
will be able to enter the switch’s CLI configuration interface. The commands used in the
Telnet CLI interface after login is the same as that in the Console interface.
DG-GS4600SE2 Configuration Guide
Chapter 1-8
Fig 1- 8 Telnet Configuration Interface
1.1.2.2 Management via HTTP
To manage the switch via HTTP, the following conditions should be met:
1) Switch has an IPv4/IPv6 address configured;
2) The host IPv4/IPv6 address (HTTP client) and the switch’s VLAN interface IPv4/IPv6
address are in the same network segment;
3) If 2) is not met, HTTP client should connect to an IPv4/IPv6 address of the switch via
other devices, such as a router.
Similar to management the switch via Telnet, as soon as the host succeeds to
ping/ping6 an IPv4/IPv6 address of the switch and to type the right login password, it can
access the switch via HTTP. The configuration list is as below:
Step 1: Configure the IP addresses for the switch and start the HTTP server function on
the switch.
For configuring the IP address on the switch through out-of-band management, see
the telnet management chapter.
To enable the WEB configuration, users should type the CLI command IP http server
in the global mode as below:
DG-GS4600SE2 Configuration Guide
Chapter 1-9
Switch>enable
Switch#config
Switch(config)#ip http server
Step 2: Run HTTP protocol on the host.
Open the Web browser on the host and type the IP address of the switch, or run
directly the HTTP protocol on the Windows. For example, the IP address of the switch is
“10.1.128.251”;
Fig 1- 9 Run HTTP Protocol
When accessing a switch with IPv6 address, it is recommended to use the Firefox
browser with 1.5 or later version. For example, if the IPv6 address of the switch is
3ffe:506:1:2::3. Input the IPv6 address of the switch is http://[3ffe:506:1:2::3] and the
address should draw together with the square brackets.
Step 3: Login to the switch.
Login to the Web configuration interface. Valid login name and password are required,
otherwise the switch will reject HTTP access. This is a method to protect the switch from
unauthorized access. As a result, when Telnet is enab led for configuring and managing
the switch, username and password for authorized Telnet users must be configured with
the following command: username <username> privilege <privilege> [password (0|7)
<password>]. To open the local authentication style with the following command:
authentication line web login local. Privilege option must exist and just is 15. Assume
an authorized user in the switch has a username of “admin”, and password of admin”, the
configuration procedure should like the following:
Switch>enable
Switch#config
Switch(config)#username admin privilege 15 password 0 admin
DG-GS4600SE2 Configuration Guide
Chapter 1-10
Switch(config)#authentication l ine web login local
The Web login interface of CS6200-28X-P-EI is as below:
Fig 1- 10 Web Login Interface
Input the right username and password, and then the main Web configuration
interface is shown as below.
Fig 1- 11 Main Web Configuration Interface
Notice: When configure the switch, the name of the switch is composed with English
letters.
1.1.2.3 Manage the Switch via SNMP Network Management
Software
DG-GS4600SE2 Configuration Guide
Chapter 1-11
The necessities required by SNMP network management software to manage switches:
1) IP addresses are configured on the switch;
2) The IP address of the client host and that of the VLAN interface on the switch it
subordinates to should be in the same segment;
3) If 2) is not met, the client should be able to reach an IP address of the switch
through devices like routers;
4) SNMP should be enabled.
The host with SNMP network management software should be able to ping the IP
address of the switch, so that, when running, SNMP network management software will
be able to find it and implement read/write operation on it. Details about how to manage
switches via SNMP network management software will not be covered in this manual,
please refer to “Snmp network management software user manual”.
1.2 CLI Interface
The switch provides thress management interface for users: CLI (Command Line
Interface) interface, Web interface, Snmp netword management software. We will
introduce the CLI interface and Web configuration interface in details, Web interface is
familiar with CLI interface function and will not be covered, please refer to “Snmp network
management software user manual”.
CLI interface is familiar to most users. As aforementioned, out-of-band management
and Telnet login are all performed through CLI interface to manage the switch.
CLI Interface is supported by Shell program, which c onsis ts of a set of configuration
commands. Those commands are categorized according to their functions in switch
configuration and management. Each category represents a different configuration mode.
The Shell for the switch is described below:
Configuration Modes
Configuration Syntax
Shortcut keys
Help function
Input verification
Fuzzy match support
1.2.1 Configuration Modes
DG-GS4600SE2 Configuration Guide
Chapter 1-12
Fig 1- 12 Shell Configuration Modes
1.2.1.1 User Mode
On entering the CLI interface, entering user entry system first. If as common user, it is
defaulted to User Mode. The prompt shown is “Switch>“, the symbol “>“ is the prompt for
User Mode. When exit command is run under Admin Mode, it will also return to the User
Mode.
Under User Mode, no configuration to the switch is allowed, only clock time and
version information of the switch can be queries.
1.2.1.2 Admin Mode
To Admin Mode sees the following: In user entry system, if as Admin user, it is
defaulted to Admin Mode. Admin Mode prompt “Switch#” can be entered under the User
Mode by running the enable command and entering corresponding access levels admin
user password, if a password has been set. Or, when exit command is run under Global
Mode, it will also return to the Admin Mode. Switch also provides a shortcut key sequence
"Ctrl+z”, this allows an easy way to exit to Admin Mode from any configuration mode
(except User Mode).
Under Admin Mode, the user can query the switch configuration information,
DG-GS4600SE2 Configuration Guide
Chapter 1-13
connection status and traffic statistics of all ports; and the user can further enter the
Global Mode from Admin Mode to modify all configurations of the switch. For this reason,
a password must be set for entering Admin mode to prevent unauthorized access and
malicious modification to the switch.
1.2.1.3 Global Mode
Type the config command under Admin Mode will enter the Global Mode prompt
“Switch(config)#”. Use the exit command under other configuration modes such as Port
Mode, VLAN mode will return to Global Mode.
The user can perform global configuration settings under Global Mode, such as MAC
Table, Port Mirroring, VLAN creation, IGMP Snooping start and STP, etc. And the user can
go further to Port Mode for configuration of all t he interfaces.
Interface Mode
Use the interface command under Global Mode can enter the interface mode
specified. Switch provides three interface type: 1. VLAN interface; 2. Ethernet port; 3.
port-channel, accordingly the three interface configuration modes.
Interface
Type
Entry Operates Exit
VLAN
Interface
Type interface vlan
<Vlan-id> command under
Global Mode.
Configure switch
IPs, etc
Use the exit
command to
return to Global
Mode.
Ethernet Port Type interface ethernet
<interface-list> command
under Global Mode.
Configure
supported duplex
mode, speed, etc.
of Ethernet Port.
Use the exit
command to
return to Global
Mode.
port-channel Type interface port-channel
<port-channel-number>
command under Global Mode.
Configure
port-channel
related settings
such as duplex
mode, speed, etc.
Use the exit
command to
return to Global
Mode.
VLAN Mode
Using the vlan <vlan-id> command under Global Mode can enter the corresponding
VLAN Mode. Under VLAN Mode the user can configure all member ports of the
DG-GS4600SE2 Configuration Guide
Chapter 1-14
corresponding VLAN. Run the exit command to exit the VLAN Mode to Global Mode.
DHCP Address Pool Mode
Type the ip dhcp pool <name> command under Global Mode will enter the DHCP
Address Pool Mode prompt “Switch(Config-<name>-dhcp)#”. DHCP address pool
properties can be configured under DHCP Address Pool Mode. Run the exit command to
exit the DHCP Address Pool Mode to Global Mode.
Route Mode
Routing Protocol Entry Operates Exit
RIP Routing
Protocol
Type router rip
command under
Global Mode.
Configure RIP
protocol parameters.
Use the exit
command to return
to Global Mode.
OSPF Routing
Protocol
Type router ospf
command under
Global Mode.
Configure OSPF
protocol parameters.
Use the exit
command to return
to Global Mode.
BGP Routing
Protocol
Type router bgp
<AS mumber>
command under
Global Mode.
Configure BGP
protocol parameters.
Use the exit
command to return
to Global Mode.
ACL Mode
ACL type Entry Operates Exit
Standard IP
ACL Mode
Type ip access-list
standard command
under Global Mode.
Configure parameters
for Standard IP ACL
Mode.
Use the exit
command to return
to Global Mode.
Extended IP
ACL Mode
Type ip access-list
extanded command
under Global Mode.
Configure parameters
for Extended IP ACL
Mode.
Use the exit
command to return
to Global Mode.
1.2.2 Configuration Syntax
Switch provides various configuration commands. Although all the commands are
different, they all abide by the syntax for Switch configuration commands. The general
commands format of Switch is shown below:
cmdtxt <variable> {enum1 | | enumN } [option1 | | optionN]
DG-GS4600SE2 Configuration Guide
Chapter 1-15
Conventions: cmdtxt in bold font indicates a command keyword; <variable> indicates a
variable parameter; {enum1 | | enumN } indicates a mandatory parameter that should
be selected from the parameter set enum1~enumN;andthesquarebracket([])in
[option1 | | optionN] indicate an optional parameter. There may be combinations of
“< >“, { } and [ ]” in the command line, such as [<variable>], {enum1 <variable>|
enum2}, [option1 [option2]], etc.
Here are examples for some actual configuration commands:
show version, no parameters required. This is a command with only a keyword and
no parameter, just type in the command to run.
vlan <vlan-id>, parameter values are required after the keyword.
firewall {enable | disable}, user can enter firewall enable or firewall disable for this
command.
snmp-server community {ro | rw} <string>, the followings are possible:
snmp-server community ro <string>
snmp-server community rw <string>
1.2.3 Shortcut Key Support
Switch provides several shortcut keys to facilitate user configuration, such as up,
down, left, right and Blank Space. If the terminal does not recognize Up and Down keys,
ctrl +p and ctrl +n can be used instead.
Key(s) Function
Back Space Delete a character before the cursor, and the cursor moves back.
Up Show previous command entered. Up to ten recently entered
commands can be shown.
Down Show next command entered. When use the Up key to get
previously entered commands, you can use the Down key to return
to the next command
Left The cursor moves one character to
the left.
You can use the Left and
Right key to modify an
entered command.
Right The cursor moves one character to
the right.
Ctrl+p ThesameasUpkey“”.
Ctrl+n ThesameasDownkey“”.
Ctrl+b ThesameasLeftkey“”.
DG-GS4600SE2 Configuration Guide
Chapter 1-16
Ctrl+f ThesameasRightkey“”.
Ctrl +z Return to the Admin Mode directly from the other configuration
modes (except User Mode).
Ctrl +c Break the ongoing c ommand process, such as ping or other
command execution.
Tab When a string for a command or keyword is entered, the Tab can
be used to complete the command or keyword if there is no
conflict.
1.2.4 Help Function
There are two ways in Switch for the user to access help information: the “help”
command and the “?”.
Access to Help Usage and function
Help Under any command line prompt, type in “help and press Enter will get
a brief description of the associated help system.
“?” 1 Under any command line prompt, enter “?” to get a command list of
the current mode and related brief description.
2 Enter a “?” after the command keyword with an embedded space.
If the position should be a parameter, a description of that
parameter type, scope, etc, will be returned; if the position should
be a keyword, then a set of keywords with brief description will be
returned; if the output is “<cr>“, then the command is complete,
press Enter to run the command.
3 A “?” immediately following a string. This will display all the
commands that begin with that string.
1.2.5 Input Verification
1.2.5.1 Returned Information: success
All commands entered through keyboards undergo syntax check by the Shell.
Nothing will be returned if the user entered a correct command under corresponding
modes and the execution is successful.
Returned Information: error
Output error message Explanation
DG-GS4600SE2 Configuration Guide
Chapter 1-17
Unrecognized command or illegal
parameter!
The entered command does not exist, or there is
error in parameter scope, type or format.
Ambiguous command At least two interpretations is possible basing on
the current input.
Invalid command or parameter The command is recognized, but no valid
parameter record is found.
This command is not exist in curren t
mode
The command is recognized, but this command
can not be used under current mode.
Please configure precursor
command "*" at first!
The command is recognized, but the
prerequisite command has not been configured.
syntax error : missing '"' before the
end of command line!
Quotation marks are not used in pairs.
1.2.6 Fuzzy Match Support
Switch shell support fuzzy match in searching command and keyword. Shell will
recognize commands or keywords correctly if the entered string causes no conflict.
For example:
1) For command “show interfaces status ethernet1/0/1”, typing “sh in status
ethernet1/0/1” will work.
2) However, for command “show running-config”, the system will report a “> Ambiguous
command!” error if only show r” is entere d, as Shell is unable to tell whether it is
“show run” or “show running-config”. Therefore, Shell will only recognize the
command if “sh ru” is entered.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504
  • Page 505 505
  • Page 506 506
  • Page 507 507
  • Page 508 508
  • Page 509 509
  • Page 510 510
  • Page 511 511
  • Page 512 512
  • Page 513 513
  • Page 514 514
  • Page 515 515
  • Page 516 516
  • Page 517 517
  • Page 518 518
  • Page 519 519
  • Page 520 520
  • Page 521 521
  • Page 522 522
  • Page 523 523
  • Page 524 524
  • Page 525 525
  • Page 526 526
  • Page 527 527
  • Page 528 528
  • Page 529 529
  • Page 530 530
  • Page 531 531
  • Page 532 532
  • Page 533 533
  • Page 534 534
  • Page 535 535
  • Page 536 536
  • Page 537 537
  • Page 538 538
  • Page 539 539
  • Page 540 540
  • Page 541 541
  • Page 542 542
  • Page 543 543
  • Page 544 544
  • Page 545 545
  • Page 546 546
  • Page 547 547
  • Page 548 548
  • Page 549 549
  • Page 550 550
  • Page 551 551
  • Page 552 552
  • Page 553 553
  • Page 554 554
  • Page 555 555
  • Page 556 556
  • Page 557 557
  • Page 558 558
  • Page 559 559
  • Page 560 560
  • Page 561 561
  • Page 562 562
  • Page 563 563
  • Page 564 564
  • Page 565 565
  • Page 566 566
  • Page 567 567
  • Page 568 568
  • Page 569 569
  • Page 570 570
  • Page 571 571
  • Page 572 572
  • Page 573 573
  • Page 574 574
  • Page 575 575
  • Page 576 576
  • Page 577 577
  • Page 578 578
  • Page 579 579
  • Page 580 580
  • Page 581 581
  • Page 582 582
  • Page 583 583
  • Page 584 584
  • Page 585 585
  • Page 586 586
  • Page 587 587
  • Page 588 588
  • Page 589 589
  • Page 590 590
  • Page 591 591
  • Page 592 592
  • Page 593 593
  • Page 594 594
  • Page 595 595
  • Page 596 596
  • Page 597 597
  • Page 598 598
  • Page 599 599
  • Page 600 600
  • Page 601 601
  • Page 602 602
  • Page 603 603
  • Page 604 604
  • Page 605 605
  • Page 606 606
  • Page 607 607
  • Page 608 608
  • Page 609 609
  • Page 610 610
  • Page 611 611
  • Page 612 612
  • Page 613 613
  • Page 614 614
  • Page 615 615
  • Page 616 616
  • Page 617 617
  • Page 618 618
  • Page 619 619
  • Page 620 620
  • Page 621 621
  • Page 622 622
  • Page 623 623
  • Page 624 624
  • Page 625 625
  • Page 626 626
  • Page 627 627
  • Page 628 628
  • Page 629 629
  • Page 630 630
  • Page 631 631
  • Page 632 632
  • Page 633 633
  • Page 634 634
  • Page 635 635
  • Page 636 636
  • Page 637 637
  • Page 638 638
  • Page 639 639
  • Page 640 640
  • Page 641 641
  • Page 642 642
  • Page 643 643
  • Page 644 644
  • Page 645 645
  • Page 646 646
  • Page 647 647
  • Page 648 648
  • Page 649 649
  • Page 650 650
  • Page 651 651
  • Page 652 652
  • Page 653 653
  • Page 654 654
  • Page 655 655
  • Page 656 656
  • Page 657 657
  • Page 658 658
  • Page 659 659
  • Page 660 660
  • Page 661 661
  • Page 662 662
  • Page 663 663
  • Page 664 664
  • Page 665 665
  • Page 666 666
  • Page 667 667
  • Page 668 668
  • Page 669 669
  • Page 670 670
  • Page 671 671
  • Page 672 672
  • Page 673 673
  • Page 674 674
  • Page 675 675
  • Page 676 676
  • Page 677 677
  • Page 678 678
  • Page 679 679
  • Page 680 680
  • Page 681 681
  • Page 682 682
  • Page 683 683
  • Page 684 684
  • Page 685 685
  • Page 686 686
  • Page 687 687
  • Page 688 688
  • Page 689 689
  • Page 690 690
  • Page 691 691
  • Page 692 692
  • Page 693 693
  • Page 694 694
  • Page 695 695
  • Page 696 696
  • Page 697 697
  • Page 698 698
  • Page 699 699
  • Page 700 700
  • Page 701 701
  • Page 702 702
  • Page 703 703
  • Page 704 704
  • Page 705 705
  • Page 706 706
  • Page 707 707
  • Page 708 708
  • Page 709 709
  • Page 710 710
  • Page 711 711
  • Page 712 712
  • Page 713 713
  • Page 714 714
  • Page 715 715
  • Page 716 716
  • Page 717 717
  • Page 718 718
  • Page 719 719
  • Page 720 720
  • Page 721 721
  • Page 722 722
  • Page 723 723
  • Page 724 724
  • Page 725 725
  • Page 726 726
  • Page 727 727
  • Page 728 728
  • Page 729 729
  • Page 730 730
  • Page 731 731
  • Page 732 732
  • Page 733 733
  • Page 734 734
  • Page 735 735
  • Page 736 736
  • Page 737 737
  • Page 738 738
  • Page 739 739
  • Page 740 740
  • Page 741 741
  • Page 742 742
  • Page 743 743
  • Page 744 744
  • Page 745 745
  • Page 746 746
  • Page 747 747
  • Page 748 748
  • Page 749 749
  • Page 750 750
  • Page 751 751
  • Page 752 752
  • Page 753 753
  • Page 754 754
  • Page 755 755
  • Page 756 756
  • Page 757 757
  • Page 758 758
  • Page 759 759
  • Page 760 760
  • Page 761 761
  • Page 762 762
  • Page 763 763
  • Page 764 764
  • Page 765 765
  • Page 766 766
  • Page 767 767
  • Page 768 768
  • Page 769 769
  • Page 770 770
  • Page 771 771
  • Page 772 772
  • Page 773 773
  • Page 774 774
  • Page 775 775
  • Page 776 776
  • Page 777 777
  • Page 778 778
  • Page 779 779
  • Page 780 780
  • Page 781 781
  • Page 782 782
  • Page 783 783
  • Page 784 784
  • Page 785 785
  • Page 786 786
  • Page 787 787
  • Page 788 788
  • Page 789 789
  • Page 790 790
  • Page 791 791
  • Page 792 792
  • Page 793 793
  • Page 794 794
  • Page 795 795
  • Page 796 796
  • Page 797 797
  • Page 798 798
  • Page 799 799
  • Page 800 800
  • Page 801 801
  • Page 802 802
  • Page 803 803
  • Page 804 804
  • Page 805 805
  • Page 806 806
  • Page 807 807
  • Page 808 808
  • Page 809 809
  • Page 810 810
  • Page 811 811
  • Page 812 812
  • Page 813 813
  • Page 814 814
  • Page 815 815
  • Page 816 816
  • Page 817 817
  • Page 818 818
  • Page 819 819
  • Page 820 820
  • Page 821 821
  • Page 822 822
  • Page 823 823
  • Page 824 824
  • Page 825 825
  • Page 826 826

Digisol DIGISOL 24/ 48 Port Gigabit Ethernet Access Layer 3 Switch User manual

Category
Software
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI