Heath Zenith 9600LED series User manual

Dated receipt required for warranty replacement.

FEATURES

• Automaticallycomesonwhenmotionisdetected.

• Automaticallyturnslightoff.

• Photocell keeps the light off during daylight

hours.

REQUIREMENTS

• Thelightcontrolrequires120voltsAC.

• If you want to use Manual Override mode, the

controlmustbewiredthroughaswitch.

NOTICE:Nottobeusedonlightdimmerortimer-

controlledcircuits.

• Some electrical codes require installation by a

qualiﬁed electrician.

• This light xture has been tested/certied us-

ing Lights of America LED Lamp Model No.

2025LEDE12.

UNPACKING

Besuretoremoveallcontentsfrompackagingand

verifyallitemsarepresentbeforeassemblingthislight

xture.Thispackageincludesthefollowingitems:

• Lantern

• ThreeLEDLamps

 (LightsofAmericaModel:2025LEDE12)

• Universalmountingbracket(X-Bar)

• Mountinghardware

• Wirenuts

• Owner’sManual

©2008 598-1338-03

Motion Sensing

Diecast Metal Lantern

Model: 9600LED Series

INSTALLATION

Forbestperformance,mountthextureabout6feet

(1.8m)abovetheground.

1. Removetwodecorativenuts.

2. RemoveX-Bar.

3. TightenmountingscrewsonX-Barngertight.

4. AttachX-Bartojunctionbox.

JunctionBox

X-Bar

DecorativeNut

LanternBase

LanternMounting

Screw

X-Bar

BracketMounting

Screw

Note:Werecommendhavinganassistanthelphold

thelanternassemblyduringthewiringprocess.

2

598-1338-03

WIRING

One Motion Light

Two Motion Lights

Recommended Grounding Method

Useagreenground“pigtail”(notprovided)and

twistoneendtogetherwiththebarexturewire

andtheboxgroundwire.Securewithawirecon-

nector.Securetheotherendofthe“pigtail”with

theGNDscrewontheX-bar.

CAUTION: DO NOT connect the RED wire

unless you want to control other lights from

the motion sensor (see Optional Wiring).

Black to black

White to white

Note:Allwiringshouldberuninaccordancewiththe

NationalElectricalCodethroughconduitoranother

acceptablemeans.Contact a qualiﬁed electrician

if there is any question as to the suitability of

the system.

WARNING: Turn power off at circuit breaker

or fuse.

Ifyouhavemetaljunctionbox,youmaynotneedthe

green“pigtail”.Ifyouareunsureaboutthegrounding

method,consultyourlocalbuildingcode.

Connectthexturewirestothewiresinthejunction

box.Twistthewirestogetherandsecurewithwire

connectors.

Black

White

Greenor

Bare

Light

Fixture

Black

White

Greenor

Bare

Light

Fixture

Light

Fixture

3

598-1338-03

Black

White

Greenor

Bare

Light

Fixture

Light

Fixture

(Standard)

Master Slave

Black

White

Greenor

Bare

Light

Fixture

Light

Fixture

Red

OPTIONAL WIRING

Thisxtureisprovidedwithasensorratedfor360Watts.Sincethextureisonlyrated180Watts,180Watts

ofadditionallightingmaybecontrolledbythissensor.

Whendeterminingwhataxtureisratedfor,donotsimplylookattheratingonthelampinthexture.Look

atthemarkingwhichspeciesthemaximumlampwattageforwhichthextureissuitable.

Onceyouhaveselectedthexturestobeconnectedanddeterminedtheirmaximumratings,addtheserat-

ingsup.Forinstance,ifyouhave3xturesrated180Watts,100Watts,and75Wattsrespectively,youhave

atotalloadof355Watts.

Wiring Diagram 1 – When wiring to control a standard light ﬁxture:Stripthemotionsensor’sredwire

andconnecttothestandardlight’sblackwire.Connectallwhitewirestogether.Totalxtureratingsmustnot

exceed360Watts(3.0A).

Wiring Diagram 2 – When wiring to control another motion sensing light ﬁxture (Master / Slave): Strip

theredwireinbothlightxtures.Connecttheredwireofthecontrolling(master)xturetotheredandblack

wiresofthecontrolled(slave)xture.Connectallwhitewirestogether.Totalxtureratingsmustnotexceed

360Watts(3.0A).

Wiring Diagram 3 – When wiring so either motion light turns on the both motion lights (Master / Master):

Striptheredwireinbothlightxtures.Connecttheredwireofonexturetotheredwireofthesecondxture.

Note:Inmostinstallations,anadditionalwire(samegageasexistinghousewire)willhavetobeinstalledin

thehousetoconnectthetwoxturesasmaster/master.Connectallwhitewirestogetherandallblackwires

together.Totalxtureratingsmustnotexceed360Watts(3.0A).

Wiring Diagram 1 Wiring Diagram 2

Wiring Diagram 3

Master

Black

White

Red

Green

or Bare

Master

Light

Fixture

Light

Fixture

4

598-1338-03

FINAL ASSEMBLY

1. Pushthewiresintothejunctionbox.Makesure

noneofthewiresgetpinched.

2.

Slidethextureassemblyontothemountingscrews.

Tightendecorativenutsremovedinstep1ofInstal-

lationsectionsecurelyagainstxturebase.

JunctionBox

MountingScrew

DecorativeNut

3. Caulkaroundxturebasewithsiliconeweather

sealant.

4. InstallthethreeLEDLamps(LightsofAmerica

Model No. 2025LEDE12 included). Note:This

xture’sE12candelabrabaseuseseitherLED

Lamps(1.5Wmaximumeach) or tungsten in-

candescentType“B”bulbs(60Wattmaximum

each).

5. Insertthreadedrodofnialthroughtopcover.Slide

starwasherontorodandthreadthenutontothe

rod.Tightensecurely.

6. Place top cover onto xture and attach using

thetwodecorativenuts(included).Handtighten

only.

TopCover

DecorativeNut

3LightBulbs

(60Watt

Maximumeach)

Fixture

Assembly

Finial

StarWasher

Nut

5

598-1338-03

TESTING AND ADJUSTMENTS

1. Turn on the circuit breaker and light switch.

Note:Sensorhasa1

1

/

2

minute warm up period

beforeitwilldetectmotion.Whenrstturnedon

wait1

1

/

2

minutes.

2. Set:

 ON-TIMEswitchtoTEST

 SENSITIVITYdialtoMidway

3.

Walkthroughthecoverageareanotingwhereyou

arewhenthelightsturnon.InTESTmode,light

willstayonfor5secondsaftersensingmotionand

thenturnoff.

4. AdjusttheSENSITIVITYtoincreaseordecrease

therangeasneeded.Toomuchsensitivitymay

causefalsetriggeringduetoheatsourcesinthe

coveragearea(seeAdjustment of Coverage Area

or Troubleshootingsection).

5. SettheamountofON-TIMEyouwantthelightto

stayonaftermotionisdetected(5or10minutes)

or...

 SettheON-TIMEtotheDUSK-to-DAWNsetting

ifyouwantthelighttostayonallnight,every

night.Thephotocellwillturnthelightoffduring

theday.

Maximum Range Maximum

Coverage Angle*

(Top View)

TEST 5

10

DUSK

MINUTES TO DAWN

– +

SEN

30ft.

(9.1m)

6ft.

(1.8m)

180°

Photocell

Least Sensitive Most Sensitive

The sensor is less sensitive to motion directly

towards it and more sensitive to motion across

coveragearea.

Sensor

Motion Motion

6

598-1338-03

Note: Whenrstturnedonwaitabout1

1

/

2

minutes

forthecircuitrytocalibrate.

*resetstoSecuritymodeatdawn.

OPERATION

Mode: On-Time Works: Day Night

Test

5Seconds x x

Security

5or10Minutes x

Automatic

Override

Dusk-to-Dawn x

Manual

Override

UntilDawn* x

MANUAL MODE

AUTO

TEST

ON-TIME Switch at 5 or 10

minutes

...backon.

1SecondOFF

then...

ManualOverridemodecanonly

be activated at night when the

ON-TIMEswitchissetto the5

or10minuteposition.

Flipthelightswitchoffforonesec-

ondthenbackontochangefrom

SECURITY mode to MANUAL

OVERRIDEmode.

To return to SECURITY mode,

either:

•turnthelightoffforoneminute

thenturniton,or...

•daylightwillautomaticallyreset

thelighttoSECURITYmode.

MODE SWITCHING SUMMARY

Flip light switch off

for one second then

back on*

*Ifyougetconfusedwhileswitchingmodes,turn

thepoweroffforoneminute,thenbackon.Afterthe

calibrationtimethecontrolwillbeintheSECURITY

mode.

MANUAL OVERRIDE MODE

ADJUSTMENT OF COVERAGE AREA

Thesensoronthislightxturedetects“motion”bythe

movementofheatacrossthecoveragearea.However,

followingareexamplesofobjectsthatalsoproduce

heatandcancausethesensortotrigger:

•PoolsofWater •AirConditioners

•DryerVents •Animals

•HeatingVents •AutomobileTrafc

Ifyoususpectthataheatsourceofthistypeistrig-

geringthesensor,reducethesensitivity.

SPECIFICATIONS

Range ...........................Upto30ft.(9.1m)[varies

withsurroundingtempera-

ture].

SensingAngle .............. 180°

ElectricalLoad ..............Up to 180WattMaximum

Tungsten Incandescent

or 5 Watt Maximum LED

(Lights of America model

2025LEDE12).

BulbType ......................E12 Candelabra Base,

Type“B”,60WattMaximum

Tungsten Incandescent or

LEDmodel2025LEDE12

 1.5Watt.

SensorCapacity ...........360Watt(3.0A)Maximum

TungstenIncandescent

PowerRequirements .... 120VAC,60Hz

OperatingModes ..........TEST, SECURITY, AUTO-

MATIC OVERRIDE and

MANUALOVERRIDE

ON-Timer ......................5or10minutes

TestTimer .....................5Seconds

Automatic

OverrideTimer ..............Dusk-to-Dawn

Manual

OverrideTimer ..............UntilDawn

SECURITY

MODE

7

598-1338-03

TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE SOLUTION

Lights will not come

on.

1. Lightswitchisturnedoff.

2. Lampislooseorburnedout.

3. Fuseisblownorcircuitbreakeristurned

off.

4. Daylightturn-offisineffect.

5. Incorrect circuit wiring, if this is a new

installation.

1. Turnlightswitchon.

2. Checklampandreplaceifburnedout.

3. Replacefuseorturncircuitbreakeron.

4. Recheckafterdark.

5. Verifywiringiscorrect.

Lights come on in

daylight.

1. Lightcontrolmaybeinstalledinarelatively

darklocation.

2. LightcontrolisinTEST.

1. Thextureisoperatingnormallyunderthese

conditions.

2. Setcontrolswitchto5or10minutesorDusk-to-

Dawn.

Lightscomeonforno

apparentreason.

Lightcontrolmaybesensingsmallanimalsor

automobiletrafc.

Reducesensitivity.

Lightsstayoncontinu-

ously.

1. Thesensormaybepickingupaheatsource

like an air vent, dryer vent, or brightly

painted,heat-reectivesurface.

2. SensorisinAutomaticOverrideorManual

Overridemode.

1. Reducesensitivity.

2. Setcontrolswitchto5or10minutes.

Lights ash on and

off.

1. Heat being reected from other objects

maybeaffectingthesensor.

2. SensorisintheTestmode.

1. Reducesensitivity.

2. WhileinTESTmode,lightonlystaysonfor5

seconds.

Lightdoesnotstayon

inManualmode.

Nearbylarge,light-coloredobjectsreecting

lightmaytriggertheshut-offfeature.

Donotpointotherlightsatthesensor.

8

598-1338-03

TWO YEAR LIMITED WARRANTY

Productwillbefreeofdefectduetoworkmanshipforaperiodoftwo(2)years.Ifproductfailswithinthe

statedlife,returndefectiveproducttoretailerofLightsofAmerica.

Warrantytermsandconditionsofretailerapply.

Warrantyandguaranteevoidifproductismisused.

Ifreplacementproductisnotavailableatretailstore,pleasereturnproductintheoriginalpackage,along

withacopyofthedatedsalesreceipt,descriptionoftheproblem,andyournameandreturnaddressto

themanufacturerattheaddresslistedbelow:

LightsofAmerica

611ReyesDrive

Walnut,CA91789

Attn:ConsumerAffairsDept.

Distributedby:

611ReyesDrive

Walnut,California91789

Tel:(800)321-8100/(909)594-7883

Fax:(909)594-6758

Website:www.lightsofamerica.com

Page is loading ...

Heath Zenith 9600LED series User manual

Heath Zenith 9600LED series User manual

in other languages

Related papers

Other documents