Sanyo VSP-8000 User manual

Brand: Sanyo

Model: VSP-8000

Type: User manual

FILE NO.

REFERENCE No.SM5310327

L8CSB/US,XE

NOTE: 1. Parts order must contain model number, part number, and description.

2. Substitute parts may be supplied as the service parts.

3. N.S.P. : Not available as service parts.

Design and specifications are subject to change without notice.

(Product Code : 117 523 55)

(U.S.A., Canada)

VSP-8000

SERVICE MANUAL

System controller

CONTENTS

SPECIFICATIONS .................................................................... 3

1. DISASSEMBLY ..................................................................... 4

2. ADJUSTMENT ...................................................................... 6

3. REWRITING THE SOFTWARE ............................................ 7

4. PARTS LIST ....................................................................... 10

CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS...........C1

Product safety should be considered when a component replacement is mand in any area of this unit.

Components indicated by the symbol ( ) in the parts list and schematic diagram designate components in which safety can

be of special significance. It is particularly recommended that only parts designated on the parts list in this manual be used for

component replacement designated by the symbol. No deviations from resistance, wattage or voltage ratings may be made for

replacement items designated by the symbol.

PRODUCT SAFETY NOTICE

(Product Code : 117 523 54)

(Europe)

(Taiwan, Korea)

VSP-8000

- 2 -

- 3 -

SPECIFICATIONS

NOTE: The specifications and external appearance of this unit are subject to change without notice.

: RS 485

: RJ-11:2 terminals

Push-lock: 1 pair

: D-SUB (9-pin): 1 port

: Address: 3-bit DIP switch

Termination: 1-bit DIP switch

: 2400, 4800, 9600, 19200 bps

: 15 groups

: Total: 256 devices

Controllers: 5 devices

Multiplexers, timelapse VCRs, cameras, and digital video recorder: 128 devices

each

: 64 devices

: Temparature: 0 to 40 °C

Relative humidity: 80 % or less

: Temparature: -20 to 60 °C

Relative humidity: 80 % or less

: 12 V DC

: 4 W

: 375 (W) x 55 (H) x 165 (D) mm

: 1.5 kg

Communication method

Control terminals

RS-232C terminal

Address/termination switch

Communication speed (baud rate)

Max. no. of groups

Max. no. of connected devices

Dome-type cameras

Ambient conditions

Storage conditions

Power supply

Power consumption

External dimensions

Weight

- 4 -

Bottom Cover

Shield Case

LCD Assy

Cabinet

CP-1 BOARD

TB-2 BOARD

1. DISASSEMBLY

1-1. REMOVAL OF CABINET AND BOARD LOCATION

Fig. 1

- 5 -

CP-1 BOARD

TB-1 BOARD

TB-2 BOARD

TB-3 BOARD

LCD

OP-1 BOARD

OP-2 BOARD

Fig.2

Fig. 3

TB-1 BOARD

TB-3 BOARD

OP-1 BOARD

OP-2 BOARD

- 6 -

1. POWER VOLTAGE ADJUSTMENT

1. Adjust VR301 so that voltage of TP302 and TP301 is 5.00 ±

0.10 V.

2. LCD LEVEL ADJUSTMENT

1. Adjust VR302 so that voltage of TP305 and TP301 is 0.575

±0.025 V.

3. JOYSTICK ADJUSTMENT FOR DIRECTION

1. The pin of JK405 is short-circuited and makes the test mode.

2. The FUNCTION button and the number 2 button are pushed

at the same time, and LCD indication is made "TEST

CENTER".

Measuring Point

Measuring Equipment

Condition

Adj. Value

Digital voltmeter

POWER ON

5.00

± 0.10 V

TP302,

TP301 (GND)

VR301

Adj. Location

2. ADJUSTMENT

Measuring Point

Measuring Equipment

Condition

Adj. Value

Oscilloscope

POWER ON

0.575

± 0.025 V

TP305,

TP301 (GND)

VR302

Adj. Location

Fig. 5

TP301

VR302

TP302

TP305

VR301

CP-1 BOARD

3. Push the ENTER button, and set the adjustment mode, and

it confirms that it is indicated with "PLEASE SPIN JST AND

PUSH ENTER" in LCD.

4. It swings, and a circular movement is done about 2-3 laps

JOYSTICK to become a width maximum.

5. It becomes adjustment mode completion if a ENTER button

is pushed and indicated with "TEST MODE" in LCD.

Adjustment is made again if it is indicated with "PLEASE

SPIN JST AND PUSH ENTER" in LCD.

6. The short circuit of the JK405 pin is removed, and the test

mode is finished.

4. JOYSTICK ADJUSTMENT FOR THE ZOOM

1. The pin of JK405 is short-circuited and makes the test mode.

2. The FUNCTION button and the number 3 button are pushed

at the same time, and LCD indication is made "TEST ZOOM

CENTER".

3. Push the ENTER button, and set the adjustment mode, and

it confirms that it is indicated with "PLEASE SLIDE JST AND

PUSH ENTER" in LCD.

4. It swings, and it slides ZOOM lever to become a width

maximum.

5. It becomes adjustment mode completion if a ENTER button

is pushed and indicated with "TEST MODE" in LCD.

Adjustment is made again if it is indicated with "PLEASE

SLIDE JST AND PUSH ENTER" in LCD.

6. The short circuit of the JK405 pin is removed, and the test

mode is finished.

Measuring Point

Measuring Equipment

Condition

Adj. Value

Adjustment

mode

LCD indication

Joystick

Adj. Location

Measuring Point

Measuring Equipment

Condition

Adj. ValueAdj. Location

Adjustment

mode

LCD indication

Zoom lever

Fig. 4

RS-232C

CONNECTOR

RESET

RS-232C

CONNECTOR

JK-405

BUTTON

- 7 -

Cancel

Connection Description

Name:

Icon:

Change Icon..

Country code:

Area code:

Phone number:

Connect using:

Configure..

Cancel

Connect To Settings

Direct to Com1

Cancel

COM1 Properties

Bits per second:

Data bits:

Parity:

Stop bits:

Flow control:

Restore Defaults

Advanced...

Hardware

Port Settings

Open

Send Text File

Look in:

File name:

Cancel

Files of type: All files (*.*)

34800

None

∗∗

Properties

3. REWRITING THE SOFTWARE

3-1. Setting up the computer

Use the Hyper Terminal which is compatible with Windows 95

, 98 or other.

1. Connect the RS-232C connector with the RS-232C con-

nector on the computer using an interlink serial interface

cable. Then turn on the power and start Windows 95 , 98 or

ohter.

2. Open Windows Explorer, and then run the file \Program

Files\Accessories\Hyper Terminal\Hypertrm.exe.

The Connection Description window appears.

3. Click the Cancel button in the Connection Description win-

dow, or enter your name and then click the OK button.

The Hyper Terminal window appears.

4. Click the File (F) button in the Hyper Terminal window, and

then click the Properties (R) button.

The Properties dialog box appears.

5. In the Properties dialog box, set Connect using (N) in Phone

Number to “Direct to COM”, and then click the Configure

(F) button.

The port Setting window of the COM1 Properties dialog box

appears.

6. In the Port Settings window, change the settings to match

the controller.

Speed: 4800, 9600, 19200 or 38400

Data bits: 8

Parity: None

Stop bits: 2

Flow control: Hardware

7. Click the OK button.

The Properties dialog box appears.

8. Click the OK button in the Properties window.

The Hyper Terminal window appears.

9. Click the Transmit (T) button in the Properties dialog box,

and then click the Send Text File (T) button.

The Send Text File dialog box appears.

10. Set File of Type (T) to “All files (*.*)”, and type the name of

the file to be transferred in File name (N).

This completes the computer settings.

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

RS-232C

CONNECTOR

RESET

RS-232C

CONNECTOR

JK-405

BUTTON

- 8 -

SANYO Controller

--:--:--

CLOCK SET

[V 2.00]REWRITE?

OK:ENTER NO:CLR

REWRITE PROGRAM

38400 8 N 2 HARD

REWRITE PROGRAM

3-3. Rewriting data

1. Follow the procedure in 3-1. Setting up the computer.

2. Turn on the power or the system controller, and check that

the initial display appears in the LCD. Then press the MENU

button to set to clock setting mode.

3. Press the 0 button and FUNCTION button simultaneously

to set to software rewriting mode.

The current version number appears in the system control-

ler LCD.

Press the CLEAR button if you want to cancel the opera-

tion.

4. Press the ENTER button to set to baud rate setting mode.

The baud rate setting display appears in the system con-

troller LCD.

Press the CLEAR button if you want to cancel the opera-

tion.

5. Press the [+] and [-] buttons to select the baud rate setting.

6. Press the ENTER button to set to software rewrite standby

mode.

The rewrite standby display appears in the system control-

ler LCD.

3-2. Resetting the computer

If an rewriting error occurs, close the Hyper Terminal, and then

repeat the procedure in 3-1. Setting up the computer from step

Speed: 4800, 9600, 19200 or 38400

Data bits: 8

Parity: None

Stop bits: 2

Flow control: Hardware

← (+)BUTTON (–)BUTTON →

Fig. 10

Initial display mode

Software rewriting mode

Baud rate setting mode

Software rewrite standby mode

Clock setting mode

→ 3 8 4 0 0 ↔ 1 9 2 0 0 ↔ 9 6 0 0 ↔ 4 8 0 0←

RS-232C

CONNECTOR

RESET

RS-232C

CONNECTOR

JK-405

BUTTON

- 9 -

REWRITING...

ADDRESS:0010

REWRITE PROGRAM

ERROR:30

REWRITE PROGRAM

COMPLETE

SANYO Controller

--:--:--

RD 2

TD 3

DTR 4

GND 5

DSR 6

RTS 7

CTS 8

4 DTR

5 GNG

6 DSR

7 RTS

8 CTS

Controller side PC side

7. Click the Open (O) button on the computer screen.

The rewriting display appears in the system controller LCD.

If the software could not be rewritten, an error code appears

in the LCD.

If an error occurs, reset the computer (see “3-2. Resetting

the computer”), and then press the ENTER button and re-

peat the rewriting operation.

Caution:

If an error occurs, do not try to reset the computer by turn-

ing off the system controller power or pressing the RESET

button.

8. When software rewriting is complete, “REWRITE PROGRAM

COMPLETE” appears in the system controller LCD.

Press the ENTER button to the initial display appears in the

LCD.

9. Turn off the power, disconnect the serial cable, and then

install the panel to the rear of the system controller.

Table of error code

3-4. RESET button

The following three items can be cleared using the RESET

button.

1. Clock (time)

2. Password code for security lock (cancels the security lock)

3. Status list

Connection Description

COM1 Properties

Open

Send Text File

Look in:

File name:

Cancel

Files of type: All files (*.*)

∗∗

Properties

Contents

Rewrite mode setting disabled

Access to rewriting prohibition adress

Rewriting operation error

Timeout error when reading

“ : ” Data receiving error

ASCII code data error

Record type error

Checksum error

Data count error

Individual data error

Transfer timeout error

Filename error

Error code

Computer screen

Software rewriting mode

Software rewriting error indication

Software rewriting completion

Wiring diagram for RS-232C interlink serial interface cable

Initial display mode

4. PARTS LIST

N.S.P.: Not available as service parts.

CABINET AND CHASSIS PARTS

L8CSB/US

72 73

75 76 77 78 79 80 81

(N.S.P.)

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

1 645 053 1385 ASSY,CASE

2 645 039 9091 BADGE (SANYO)

3 645 053 1620 ASSY,TB-2

4 645 053 1248 SCREW M2*6TP

5 645 053 1811 ASSY,LCD

6 645 053 1255 SCREW M3*6

7 645 039 8803 G TERMINAL SCREW M3*10

8 645 053 1392 REAR PANEL

9 645 053 1675 RS232C COVER

10 645 039 8926 HOLDER (Include in the ASSY TB-3)

11 645 053 1637 ASSY,TB-3

12 645 053 1835 KEY SW

13 613 197 9895 ASSY,KNOB,JOY

14 645 053 1668 ZOOM NOB

15 645 053 1408 SHIELD CASE (N.S.P.)

16 645 039 7752 SCREW M3*10TP

17 645 038 5971 CABLE CRAMPER (B)

18 645 053 1613 ASSY,TB-1

19 645 053 1606 ASSY,OP-2

20 645 053 1590 ASSY,OP-1

21 645 053 1842 ASSY,CP-1

22 645 039 8179 COVER,BOTTOM

23 645 039 8797 FOOT (T3, DIA10)

24 645 039 8278 (REW)

25 645 039 8285 (PLAY)

26 645 039 8315 (REVERSE)

27 645 039 8292 (FF)

28 645 039 8322 (STOP)

29 645 053 1422 (TRACKING V.LOCK+)

30 645 039 8384 (REC/PLAY SPEED UP)

31 645 039 8377 (REC/PLAY SPEED DOWN)

32 645 053 1415 (TRACKING V.LOCK-)

33 645 039 8360 (EJECT)

34 645 039 8308 (REC)

35 645 039 8339 (STILL)

36 645 039 8391 (MULTI)

37 645 039 8407 (QUAD)

38 645 053 1507 (CAM MPX)

39 645 039 8414 (PLUS)

40 645 039 8445 (SEQ)

41 645 039 8476 (VCR)

42 645 053 1521 (EXIT BACK)

43 645 039 8490 (NEXT)

44 645 039 8469 (LIVE)

45 645 039 8483 (FULL)

46 645 053 1514 (MON2 SPOT)

47 645 039 8421 (STILL)

48 645 039 8186 (ELS)

49 645 039 8193 (BLC)

50 645 053 1446 (PAN)

51 645 039 8209 (AWC SET)

52 645 039 8230 (AWC RESET)

53 645 053 1453 (TOUR)

54 645 053 1484 (AUX)

55 645 053 1477 (FOUCUS F)

56 645 039 8223 (IRIS+)

57 645 053 1460 (FOUCUS N)

58 645 039 8216 (IRIS-)

59 645 053 1439 (SEQ)

60 645 039 8513 (1)

61 645 039 8520 (2)

62 645 039 8551 (5)

63 645 039 8537 (3)

64 645 039 8568 (6)

65 645 039 8599 (9)

66 645 039 8629 (+)

67 645 039 8605 (0)

68 645 039 8582 (8)

69 645 039 8612 (-)

70 645 039 8575 (7)

71 645 039 8544 (4)

72 645 053 1538 (MENU)

73 645 053 1491 (AF)

74 645 053 1545 (ENTER)

75 645 039 8636 (ALARM LIST)

76 645 053 1361 (STATUS LIST)

77 645 039 8650 (MODE)

78 645 039 8667 (INDIVIDUAL)

79 645 039 8674 (GROUP)

80 645 039 8681 (FUNCTION)

81 645 039 8698 (CLEAR)

82 645 053 1781 SCREW WITH PLATE M3*10TP

83 645 053 1774 NUT(NUT+WASHER+SCREW)

D-SUB CONNECTOR (Included in the ASSY TB-1)

Note:

1. Materials of Resistors are abbreviated as follows ;

Resistors

MT-FILM Metallized Film Resistor

MT-GLAZE Metallized Glaze Resistor

OXIDE-MT Oxide Metallized Film Resistor

2. Capacitors

UF :

F PF : pF

3. Inductors

UH :

H MH : mH

4. N.S.P. : Not available as service parts.

ELECTRICAL PARTS

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

ASSY,OP-1

645 053 1590

(DIODES)

D1057 645 039 7998 DIODE ALLEY MA153A

D1058 645 039 7998 DIODE ALLEY MA153A

D1059 645 039 7998 DIODE ALLEY MA153A

D1060 645 039 7998 DIODE ALLEY MA153A

D1061 645 039 7998 DIODE ALLEY MA153A

D1062 645 039 7998 DIODE ALLEY MA153A

D1063 645 039 7998 DIODE ALLEY MA153A

D1064 645 039 7998 DIODE ALLEY MA153A

(CAPACITORS)

C1001 645 039 7547 CERAMIC 0.1UF+80,-20%,50V

C1002 645 039 7547 CERAMIC 0.1UF+80,-20%,50V

C1003 645 053 1200 CERAMIC 0.01UF+80,-20%,50V

C1004 645 053 1200 CERAMIC 0.01UF+80,-20%,50V

(RESISTOR)

R1062 645 039 7554 MT-GLAZE 1/8W 0OHM

(MISCELLANEOUS)

U1001 645 053 1699 STICK CONTROLER (ALPS)

U1002 645 053 1699 STICK CONTROLER (ALPS)

CN101 645 039 8902 16P CABLE ASSY (N.S.P.)

CN102 645 053 1705 8P CABLE ASSY (N.S.P.)

ASSY,OP-2

645 053 1606

(DIODES)

D2008 645 053 1934 DIODE ALLEY MA153A

D2009 645 053 1934 DIODE ALLEY MA153A

D2010 645 053 1934 DIODE ALLEY MA153A

D2011 645 053 1934 DIODE ALLEY MA153A

(BUZZER)

BZ201 645 053 1903 PIEZO BUZZER

(MISCELLANEOUS)

CN201 645 053 1866 9P CABLE ASSY (N.S.P.)

CN202 645 053 1859 6P CABLE ASSY (N.S.P.)

ASSY,CP-1

645 053 1842

(INTEGRATED CIRCUITS)

IC301 645 053 1958 IC,MAX202CSE

IC302 410 428 8708 IC,LC87F5064

IC303 645 053 1972 IC,PST9127SOT-25

IC305 645 053 1965 IC,MAX3082CSA

IC306 645 053 1941 IC,AT24C64-10PC

IC306 645 053 1989 IC SOCKET

IC307 645 053 1927 IC,MN1382-R

IC308 645 053 1873 IC,MAX3100EEE

IC309 645 053 1880 IC,TC74HC86

(SEMICONDUCTORS)

Q3001 645 039 7844 DIGITAL TRANSISTOR DTC114EKA

Q3002 645 039 7844 DIGITAL TRANSISTOR DTC114EKA

Q3003 645 053 1279 DIGITAL TRANSISTOR DTC144EK

Q3004 645 039 7844 DIGITAL TRANSISTOR DTC114EKA

(DIODES)

D3001 645 039 7981 DIODE SB10-05P

D3002 645 039 7974 DIODE SB05-50P

D3003 645 039 7868 DIODE 1SS355

D3004 645 039 7868 DIODE 1SS355

D3005 645 039 7868 DIODE 1SS355

D3006 645 039 7868 DIODE 1SS355

D3007 645 039 7974 DIODE SB05-50P

D3008 645 039 7868 DIODE 1SS355

D3009 645 039 7868 DIODE 1SS355

D3010 645 039 7868 DIODE 1SS355

D3011 645 039 7868 DIODE 1SS355

D3012 645 039 7868 DIODE 1SS355

D3013 645 039 7868 DIODE 1SS355

D3014 645 039 7868 DIODE 1SS355

D3015 645 039 7868 DIODE 1SS355

(INDUCTOR)

L3001 645 053 1293 INDUCTOR 100UH

(DC/DC CONVERTER)

U3001 645 039 8025 DC/DC CONVERTOR BP5220X

(VARIABLE RESISTORS)

VR301 645 039 7820 VR SEMI FIXED 1MOHM

VR302 645 039 7837 VR SEMI FIXED 4.7KOHM

(RESONATORS)

X3001 645 053 1262 RESONATOR CERAMIC,10MHZ

X3002 645 040 2135 RESONATOR CRYSTAL,32.768KHZ

X3003 645 053 1286 RESONATOR CERAMIC,3.68MHZ

(CAPACITORS)

C3001 645 039 7509 CERAMIC,100PF+,-5%,50V

C3002 645 039 7509 CERAMIC,100PF+,-5%,50V

C3003 645 039 7509 CERAMIC,100PF+,-5%,50V

C3004 645 039 7509 CERAMIC,100PF+,-5%,50V

C3005 645 039 7509 CERAMIC,100PF+,-5%,50V

C3006 645 039 7509 CERAMIC,100PF+,-5%,50V

C3007 645 039 7509 CERAMIC,100PF+,-5%,50V

C3008 645 039 7509 CERAMIC,100PF+,-5%,50V

C3009 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3010 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3011 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3012 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3013 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3014 645 039 7523 CERAMIC,15PF+,-5%,50V

C3015 645 039 7523 CERAMIC,15PF+,-5%,50V

C3016 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3017 645 039 7530 CERAMIC,20PF+,-5%,50V

C3021 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3022 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3023 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3024 645 039 7547 CERAMIC,0.1UF+80,-20%,50V

C3025 645 039 7479 ELECTRIC,1000UF,+,-20%,50V

C3026 645 039 7486 ELECTRIC,47UF,+,-20%,50V

C3027 645 039 7486 ELECTRIC,47UF,+,-20%,50V

C3028 645 039 7493 ELECTRIC,470UF,+,-20%,25V

C3029 645 039 7462 ELECTRIC,10UF,+,-20%,16V

C3030 645 039 7462 ELECTRIC,10UF,+,-20%,16V

C3031 645 039 7462 ELECTRIC,10UF,+,-20%,16V

C3032 645 039 7462 ELECTRIC,10UF,+,-20%,16V

C3033 645 039 7486 ELECTRIC,47UF,+,-20%,50V

C3034 645 039 7448 ELECTRIC,1UF,+,-20%,50V

C3035 645 039 7462 ELECTRIC,10UF,+,-20%,16V

C3036 645 039 7486 ELECTRIC,47UF,+,-20%,50V

LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION

CN305 645 039 7912 6P CONNECTOR (N.S.P.)

CN306 645 039 7905 3P CONNECTOR (N.S.P.)

CN307 645 053 1828 2P CONNECTOR (N.S.P.)

ASSY,TB-1

645 053 1613

(SWITCHES)

S4001 645 039 8001 DIP SW

S4002 645 053 1354 TACT SW

S4003 645 053 1309 SLIDE SW

S4004 645 039 8094 S POWER SW

(JACKS/TERMINAL)

JK401 645 039 7721 DC JACK

JK402 645 031 6913 MODULAR JACK

JK403 645 031 6913 MODULAR JACK

JK404 645 039 8070 PUSH LOCK TERMINAL(2P)

JK405 645 039 8100 TEST PIN

(FILTERS)

F4001 645 039 7806 EMI FILTOR

F4002 645 039 7806 EMI FILTOR

F4003 645 039 7806 EMI FILTOR

F4004 645 039 7813 EMI FILTOR

(INDUCTORS)

L4001 645 039 7790 INDUCTOR,0.47UH

L4002 645 039 7790 INDUCTOR,0.47UH

(CAPACITORS)

C4001 645 039 7516 CERAMIC 0.01UF+80,-20%,50V

C4002 645 039 7516 CERAMIC 0.01UF+80,-20%,50V

(DIODES)

D4001 645 053 1347 ZENNER DIODE

D4002 645 053 1347 ZENNER DIODE

D4003 645 053 1347 ZENNER DIODE

D4004 645 053 1347 ZENNER DIODE

(RESISTORS)

R4001 645 039 7608 MT-GLAZE 1/8W 120OHM+,-0.5%

R4002 645 039 7554 MT-GLAZE 1/8W 0OHM

R4003 645 039 7554 MT-GLAZE 1/8W 0OHM

R4004 645 039 7554 MT-GLAZE 1/8W 0OHM

R4005 645 039 7554 MT-GLAZE 1/8W 0OHM

R4006 645 039 7554 MT-GLAZE 1/8W 0OHM

R4008 645 039 7554 MT-GLAZE 1/8W 0OHM

R4009 645 039 7554 MT-GLAZE 1/8W 0OHM

R4010 645 039 7554 MT-GLAZE 1/8W 0OHM

R4011 645 039 7554 MT-GLAZE 1/8W 0OHM

(MISCELLANEOUS)

645 053 1774 NUT(NUT+WASHER+SCREW)

D-SUB CONNECTOR

CN403 645 039 8087 CONNECTOR (9P) D-SUB

CN401 645 039 8872 6P CABLE ASSY (N.S.P.)

CN402 645 039 8896 9P CABLE ASSY (N.S.P.)

ASSY,TB-2

645 053 1620

(LED)

D5001 645 039 7882 LED(GREEN)

D5002 645 039 7875 LED(RED)

(MISCELLANEOUS)

CN501 645 039 8865 3P CABLE ASSY (N.S.P.)

ASSY,TB-3

645 053 1637 ASSY,TB-3

(BATTERY)

Z6001 645 039 8063 BATTERY

(MISCELLANEOUS)

CN601 645 039 7936 CONNECTOR(2P) (N.S.P.)

645 039 8926 HOLDER

C3037 645 039 7462 ELECTRIC,10UF,+,-20%,16V

C3038 645 039 7455 ELECTRIC,100UF,+,-20%,6.3V

C3039 645 039 7547 CERAMIC 0.1UF+80,-20%,50V

C3040 645 039 7516 CERAMIC 0.01UF+80,-20%,50V

C3041 645 039 7516 CERAMIC 0.01UF+80,-20%,50V

C3042 645 039 7516 CERAMIC 0.01UF+80,-20%,50V

C3046 645 039 7547 CERAMIC 0.1UF+80,-20%,50V

C3047 645 053 1194 CERAMIC 0.01UF+,-20%,50V

(RESISTORS)

R3001 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3002 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3003 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3004 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3005 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3006 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3007 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3008 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%

R3009 645 039 7691 MT-GLAZE 1/8W 560OHM+,-0.5%

R3010 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3011 645 039 7684 MT-GLAZE 1/8W 470KOHM+,-0.5%

R3012 645 039 7592 MT-GLAZE 1/8W 10MOHM+,-0.5%

R3013 645 039 7653 MT-GLAZE 1/8W 330KOHM+,-0.5%

R3014 645 039 7677 MT-GLAZE 1/8W 4.7KOHM+,-0.5%

R3015 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3017 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3018 645 039 7615 MT-GLAZE 1/8W 1.5KOHM+,-0.5%

R3020 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3022 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3025 645 039 7691 MT-GLAZE 1/8W 560OHM+,-0.5%

R3026 645 039 7691 MT-GLAZE 1/8W 560OHM+,-0.5%

R3028 645 039 7615 MT-GLAZE 1/8W 1.5KOHM+,-0.5%

R3029 645 039 7615 MT-GLAZE 1/8W 1.5KOHM+,-0.5%

R3030 645 039 7660 MT-GLAZE 1/8W 390OHM+,-0.5%

R3031 645 039 7707 MT-GLAZE 1/8W 68OHM+,-0.5%

R3032 645 039 7707 MT-GLAZE 1/8W 68OHM+,-0.5%

R3033 645 039 7561 MT-GLAZE 1/8W 100OHM+,-0.5%

R3034 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3035 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3036 645 039 7639 MT-GLAZE 1/8W 270KOHM+,-0.5%

R3037 645 053 1217 MT-GLAZE 1/8W 4.3KOHM+,-0.5%

R3041 645 039 7554 MT-GLAZE 1/8W 0OHM

R3042 645 039 7554 MT-GLAZE 1/8W 0OHM

R3043 645 039 7554 MT-GLAZE 1/8W 0OHM

R3053 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3054 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3055 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3056 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3057 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3058 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3059 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3060 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3064 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3065 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3066 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3067 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3068 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3069 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3070 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3071 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3072 645 039 7554 MT-GLAZE 1/8W 0OHM

R3074 645 039 7554 MT-GLAZE 1/8W 0OHM

R3080 645 039 7554 MT-GLAZE 1/8W 0OHM

R3081 645 039 7554 MT-GLAZE 1/8W 0OHM

R3082 645 039 7554 MT-GLAZE 1/8W 0OHM

R3084 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3085 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

R3086 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3087 645 053 1224 MT-GLAZE 1/8W 470KOHM+,-0.5%

R3089 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3090 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%

R3091 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%

(MISCELLANEOUS)

CN301 645 039 7950 16P CONNECTOR (N.S.P.)

CN302 645 039 7950 16P CONNECTOR (N.S.P.)

CN303 645 053 1323 9P CONNECTOR (N.S.P.)

CN304 645 039 7929 9P CONNECTOR (N.S.P.)

CN308 645 053 1316 8P CONNECTOR (N.S.P.)

ASSY,LCD

645 053 1811

(LCD)

629 016 4750 LCD DM1623-7BL3

(MISCELLANEOUS)

645 039 8919 16P CABLE ASSY

ACCESSORIES & PACKING MATERIALS

613 196 5065 INSTRUCTION MANUAL(U.S.A. & CANADA)

613 196 5058 INSTRUCTION MANUAL(EUROPE)

645 039 8940 AC ADAPTOR (U.S.A. & CANADA)

645 039 8957 AC ADAPTOR (EUROPE.)

645 053 1712 MODULAR CABLE

645 053 1729 PACKING CASE

645 038 6046 POLY BAG

LOCATION PARTS NO. DESCRIPTION

CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS

TABLE OF CONTENTS

1. OVERALL WIRING AND CIRCUIT DIAGRAMS

OVERALL WIRING ........................................................................................................................................... C2

TB-1 BOARD ..................................................................................................................................................... C2

CP-1 BOARD .................................................................................................................................................... C3

OP-1 BOARD .................................................................................................................................................... C4

OP-2 BOARD .................................................................................................................................................... C5

TB-2 BOARD ..................................................................................................................................................... C5

TB-3 BOARD ..................................................................................................................................................... C5

2. PRINTED WIRING BOARDS (P.W.B.)

CP-1 P.W.B. ...................................................................................................................................................... C6

TB-1 P.W.B. ...................................................................................................................................................... C6

OP-1 P.W.B. ...................................................................................................................................................... C7

OP-2 P.W.B. ...................................................................................................................................................... C7

TB-2 P.W.B. ...................................................................................................................................................... C7

TB-3 P.W.B. ...................................................................................................................................................... C7

PRODUCT SAFETY NOTICE

THE COMPONENTS DESIGNATED BY A SYMBOL ( ) IN THIS

SCHEMATIC DIAGRAM DESIGNATES COMPONENTS WHOSE

VALUE ARE OF SPECIAL SIGNIFICANCE TO PRODUCT SAFETY.

SHOULD ANY COMPONENT DESIGNATED BY A SYMBOL NEED TO

BE REPLACED, USE ONLY THE PART DESIGNATED IN THE PARTS

LIST.

DO NOT DEVIATE FROM THE RESISTANCE, WATTAGE AND VOLT-

AGE RATINGS SHOWN.