TEAC CD-W552PUK Owner's manual

Brand: TEAC

Model: CD-W552PUK

Type: Owner's manual

This manual is also suitable for

QUICK CD-W552PUK

TEAC CD-W552PUK is a high-performance CD-RW drive system with a reading speed factor of approximately 52x, enabling fast data transfer speeds. It supports writing to CD-R media with speeds ranging from 4X to 40X and CD-RW media with speeds from 2X to 24X, allowing for efficient data burning. The drive is compatible with various operating systems, including Windows 98 Second Edition, Me, 2000 Professional, and XP Home/Professional, ensuring seamless integration with your computer.

page 1

With a reading speed factor of approx. 52 the

CD-W552PUK is a modern high performance

CD-RW drive system. It is able to write to CD-R

media

with a writing speed of 4X, 8X, 12X, and

16X (CLV mode), of 24X, 32X, and 40X (partial

CAV mode) and it is able to write to CD-RW me-

dia with a writing speed of 2X, 4X, 8X, 10X, 12X

and 16X (CLV mode), and of 24X (partial CAV

mode)

Very important:

TEAC assumes no responsibility for data

loss caused by the operation that is not

in accordance to this document, or data

loss caused by natural disaster, fire,

power outage, or spontaneous defect of

this product.

Components

CD-RW drive unit, AC adapter, USB interface

cable, CD with software, 1 CD-R, quick Installa-

tion Guide, warranty booklet

System Requirements

PC/AT compatible machine with a USB1.1 or

USB2.0 interface, CPU Intel Pentium II 266MHz

or more, main memory of 64MB or more, free

hard drive space of approx. 800MB or more when

writing to the CD-R or CD-RW disc.

Conforming OSes

Microsoft Windows 98 Second Edition, Microsoft

Windows Me, Microsoft Windows 2000 Profes-

sional, Microsoft Windows XP Home Edition/Pro-

fessional

The drive does not conform to Windows 95, Win-

dows 98 and MS-DOS.

Setting up the drive

Windows Me, Windows 2000 and Windows XP

operating systems have the native drivers for

USB controller and TEAC CD-W552PUK. There-

fore, when this drive is connected, Windows will

automatically install the appropriate driver and

the drive will be ready to be used. You do not

have to perform any special installation or

uninstallation.

TEAC CD-W552PUK CD-RW Drive

Quick Installation Guide

However, it is required that the device driver be

installed from the CD provided with this product

when you use Windows 98 Second Edition (Win-

dows 98SE). Set the provided CD in one CD-

ROM drive (not in the USB drive) of your com-

puter.

Very important:

Do not connect the drive if your PC is in

sleep or in suspend mode. Prior to con-

nect the drive you have to set your PC

in the normal mode of operation.

(1) Turn on the power of the computer and wait

for the desktop screen to appear.

(2) Connect the DC output plug of the provided

AC adapter to the DC input connector of the

drive.

OFF

+5V

+12V

Audio

(3) Connect the other DC plug of the provided

AC adapter to an outlet. Set the power switch

of your USB drive to on.

(4) Connect the drive and the computer using

the provided USB cable. Insert the mini B

plug of the provided USB connector to the

USB connector at the back of the drive.

OFF

+5V

+12V

Audio

page 2

Insert the A plug of the USB connector to

the USB terminal of the computer.

(5) Locate the USB terminal of your computer.

Refer to the instruction manual of your com-

puter for its location. The following logo is

usually indicated near the USB terminal.

(6) There appear some messages on the screen

followed by the appearance of an CD-ROM

icon in the window My Computer. Now the

drive is ready to use.

Very important:

When you are using Windows 98SE and

the drive is connected for the first time,

it is required to read and install the de-

vice driver file from the provided CD.

Driver installation under Windows98SE

(1) Connect as described before the dedicated

AC adapter to the drive, then connect the

USB interface cable between the drive and

your computer.

(2) Add New Hardware Wizard starts automati-

cally.

(3) Ensure your driver CD is inserted correctly

into a CD-ROM drive and select “Search for

the best driver for your device (Recom-

mended)”. Click Next.

(4) When specifying the location to search the

driver, select “CD-ROM drive” or check

“Specify a location” and input the location of

the driver folder if you have saved them in

advance on your computer (The window

below is an example if the folder CDW552PU

in drive C: is specified). Click Next.

(5) If the driver was found (TTP300.INF for

USB2.0; TTPSL11R.INF for USB1.1), click

on Next.

(6) After sucessfully finishing the installation the

hardware assistant is closed with Finish.

Important:

If an error message appears you may

move one step backwards or cancel the

process (using Cancel) and try it again

later. If installation of the driver fails you

will see in the device manager an excla-

mation mark (!) or a question mark (?).

Remove the driver and start the installa-

tion process again.

Disconnecting the drive

The drive can be disconnected from the PC if it

is not used any longer during the actual session.

It is of major importance to logoff the drive at the

PC before disconnecting it.

(1) Close the program that uses the drive.

(2) Confirm that the busy indicator of the drive

is off.

(3) Click the Remove icon on the Taskbar.

(4) Select the removing drive with the name

assigned to the drive.

(5) The Remove Hardware confirmation mes-

sage „Save to remove storage device“ ap-

pears. Click the OK button.

(6) Remove the plug of the USB cable from the

USB terminal of the computer.

page 3

Important:

If liquid is allowed to poor into the drive,

it may cause a serious malfunction, an

electric shock or a fire. When cleaning

with liquid, be sure to remove the pro-

vided AC adapter from the wall outlet

after disconnecting the drive from your

computer.

Important:

Do not use cleaning CDs which will re-

move dirt of the lense of the laser aided

by a little brush. Do not clean the inner

parts of your TEAC CD-RW drive with

compressed air. Any of these methods

may cause damage to your TEAC drive.

Handling

Check the CD before inserting it into the drive. It

should not have finger prints or other dirt on it.

Especially at high reading velocities dirt may in-

crease the number of reading errors.

Very important:

Shape CDs, a kind of CD which is not

shaped like the normal round CD, are

not allowed to be used in this drive. Oth-

erwise rotational forces may cause se-

vere damage to the drive.

Installing the Writer Software

As a general precaution the installation of the

hardware has to be carried out as described be-

fore. The software installation starts with activat-

ing the reading functionality of the drive as this

is well known with any conventional CD-ROM

drive.

If the reading functionality is available the next

installation step is to achieve the writing func-

tionality provided of the writer software. More

details according the installation of your writer

software you will find in its documention [Help].

Rear panel

ON OFF

+5V

+12V

Audio

USB 2.0

Ventilator

Analogue

audio output

USB

connector

DC input

connector

Power switch

Important:

Do not disconnect the power cord or the

USB cable which connects the PC and

the drive without carrying out the logoff

procedure. Otherwise this may lead to

loss of data and erroneous operation of

the PC.

Names and Functions

Front panel

Playing back the audio CD

Use Windows Media Player or audio CD play-

back software such as Microsoft CD Player for

playing back the audio CD using the drive. The

operation method differs depending on the soft-

ware and versions. Refer to the operation manual

of your computer or software for details.

Cleaning and maintenance of your

TEAC USB CD-RW drive

TEAC drives will not need maintenance if used

as specified in this manual. Usually there are only

problems with dirty or defective CDs.

Eject button

Audio

output jack

Busy LEDs

Volume control

Emergency hole

page 4

Warranty is provided under the terms of the TEAC warranty conditions.

In case of warranty: www.teac.de/support

Applicable disc format CD-DA, CD-ROM Mode-1, CD-ROM XA

Photo CD multi-session, CD-TEXT

CD-I, Video CD, CD Extra (CD Plus)

Applicable disc

type

Type CD-ROM, CD-DA

CD-R, CD-RW

Size 12 cm, 8 cm

An actual list of media recommended by TEAC can be found at TEACs web site under

www.teac.de/support. Please select the menu "CD-Medias".

Interface USB1.1 / USB2.0 (High Speed)

Data rate USB1.1: 1.5MB/s = 12Mbit/s

USB2.0: 60MB/s = 480Mbit/s

Data transfer

speed

CD-ROM read 7,800 KB/s (maximum at 52 x)

52 x CAV CD-ROM (Mode-1)

CD-ROM XA

CD-DA (Digital Audio Extraction)

32 x CAV CD-RW, Video CD

8 x CLV CD-Audio, Video CD

Write speed CD-R/RW write 7,800 KB/s (maximum at 52 x)

CD-R 52 x CAV, 40/32/24 x Partial-CAV, 16/12/8/4 x CLV

CD-RW 24 x Partial-CAV, 16/12/10/8/4/2 x CLV

Write mode Disc-at-once, Session-at-once, Track-at-once, Packet

write

Access time 140 ms (average)

Data buffer 2MB

Audio out Line out:

0.7Vrms±0.02Vrms (at load of 130 Ohm typ.)

ear phone (ø3.5mm stereo mini jack):

1.33Vrms±0.12Vrms (at load of 132 Ohm typ.)

Power

consumption

primary: 240V/110V 50/60Hz 850mA

secondary: 5V/2.5A, 12V/1.5A

Environmental condition

Temperature Operating 5°C to 45°C

Non-operating -20°C to 60°C

Relative humidity Operating 8% to 80% (non-condensing)

Non-operating 15% to 85% (non-condensing)

Safety standards CE

Dimensions 167 (W) × 55 (H) × 273 (D) mm

Weight 1.85 kg (without AC adapter and interface cable)

Changes in specifications and features may be made without notice or obligation.

Specifications

TEAC CD-W552PUK Owner's manual

Brand: TEAC

Model: CD-W552PUK

Type: Owner's manual

This manual is also suitable for

QUICK CD-W552PUK

Download PDF

report

TEAC CD-W552PUK Owner's manual

This manual is also suitable for

TEAC CD-W552PUK Owner's manual

Related papers

Other documents