3.1 Parameter Setup & Inquiry
3.2 System Parameter Setup
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold (Setup) key for more than 3s, LCD will display:
Key in password (default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
PTZ addr:028 ④
password:----
*ptz setup
system setup
*PTZ addr 001
P:PELCO D
:
*PTZ addr:
P:Pelco D
028
PTZ addr:028
*P:PelcoP
PTZ addr:028
*B:2400
PTZ addr:028
*B:9600
3.1 Parameter Setup And Inquiry
PTZ addr:
P:PelcoD
028
*
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
— —07
PTZ addr:028 ④
password:----
*PTZ addr 001
P:PELCO D
:
*PTZ addr:
P:Pelco D
028
PTZ addr:028
*P:PelcoP
PTZ addr:028
*B:2400
PTZ addr:028
*B:9600
3.1 Parameter Setup And Inquiry
PTZ addr:
P:PelcoD
028
*
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
— —07
PTZ addr:028 ④
password:----
*ptz setup
system setup
*PTZ addr:
P:Pelco D
028
PTZ addr:028
*P:PelcoP
PTZ addr:028
*B:2400
PTZ addr:028
*B:9600
3.1 Parameter Setup And Inquiry
PTZ addr:
P:PelcoD
028
*
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
— —07
PTZ addr:028 ④
password:----
*ptz setup
system setup
*PTZ addr 001
P:PELCO D
:
PTZ addr:028
*P:PelcoP
PTZ addr:028
*B:2400
PTZ addr:028
*B:9600
3.1 Parameter Setup And Inquiry
PTZ addr:
P:PelcoD
028
*
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
— —07
PTZ addr:028 ④
password:----
*ptz setup
system setup
*PTZ addr 001
P:PELCO D
:
*PTZ addr:
P:Pelco D
028
PTZ addr:028
*P:PelcoP
PTZ addr:028
*B:2400
PTZ addr:028
*B:9600
3.1 Parameter Setup And Inquiry
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
Move the joystick toward right, LCD will display:
— —07
PTZ addr:028 ④
password:----
*ptz setup
system setup
*PTZ addr 001
P:PELCO D
:
*PTZ addr:
P:Pelco D
028
PTZ addr:028
*B:2400
PTZ addr:028
*B:9600
3.1 Parameter Setup And Inquiry
PTZ addr:
P:PelcoD
028
*
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
Press joystick, nish protocol setup and switch to baud rate setup, LCD will display:
— —07
PTZ addr:028 ④
password:----
*ptz setup
system setup
*PTZ addr 001
P:PELCO D
:
*PTZ addr:
P:Pelco D
028
PTZ addr:028
*P:PelcoP
PTZ addr:028
*B:9600
3.1 Parameter Setup And Inquiry
PTZ addr:
P:PelcoD
028
*
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
Move the joystick toward right till LCD display:
Press joystick, nish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter. After nishing all setup, press (ESC) key to quit
setup.
— —07
PTZ addr:028 ④
password:----
*ptz setup
system setup
*PTZ addr 001
P:PELCO D
:
*PTZ addr:
P:Pelco D
028
PTZ addr:028
*P:PelcoP
PTZ addr:028
*B:2400
3.1 Parameter Setup And Inquiry
PTZ addr:
P:PelcoD
028
*
PARAMETER SETUP AND INQUIRY
setup and inquiry
e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600.
in normal status, press and hold【setup】key for more than 3s, LCD will display:
key in password(default: 8888), press joystick, LCD will display:
Press joystick, LCD will display:
Move the joystick toward left/right to select PTZ 28, LCD will display:
Press joystick, LCD will display:
Move the joystick toward right, LCD will display:
Press joystick, finish protocol setup and switch to baud rate setup, LCD will display:
Move the joystick toward right till LCD display:
Press
joystick, finish setup and back to select PTZ ID menu, repeat above steps,
you can set other PTZ parameter.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including: language, password, key-press volumn, key backlight,
default factory setup.
The following example is “default factory setup” operation steps:
Press joystick, the buzzer will give out long time sound, the question mark “?“ in
screen will disappear, denote setup nished, press (ESC) key to quit setup.
ptz setup
*system setup
*ptz setup
system setup
PTZ addr:028 ④
password:----
— —08
* 0-255
P:PELCO D
PTZ addr:
3.2 System Parameter Setup
*language
password setup
setup and inquiry
after finishing all setup, press【ESC】key to quit setup.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including:language、password、key-press volumn、key backlight、
default factory setup。The following example is “default factory setup”operation
steps:
In normal status, press and hold 【setup】 key for more than 3s, LCD will Dis
play:
Key in password(default password: 8888), press joystick, LCD will display:
Move the joystick toward down, LCD will display:
Press joystick, LCD will display:
Move joystick till LCD display:
Move joystick toward right, LCD will display:
* default factory
setup
*default factory
setup ?
In normal status, press and hold (Setup) key for more than 3s, LCD will Display:
ptz setup
*system setup
*ptz setup
system setup
PTZ addr:028 ④
password:----
— —08
* 0-255
P:PELCO D
PTZ addr:
3.2 System Parameter Setup
*language
password setup
setup and inquiry
after finishing all setup, press【ESC】key to quit setup.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including:language、password、key-press volumn、key backlight、
default factory setup。The following example is “default factory setup”operation
steps:
In normal status, press and hold 【setup】 key for more than 3s, LCD will Dis
play:
Key in password(default password: 8888), press joystick, LCD will display:
Move the joystick toward down, LCD will display:
Press joystick, LCD will display:
Move joystick till LCD display:
Move joystick toward right, LCD will display:
* default factory
setup
*default factory
setup ?
Key in password (default password: 8888), press joystick, LCD will display:
PTZ addr:028 ④
password:----
— —08
* 0-255
P:PELCO D
PTZ addr:
3.2 System Parameter Setup
*language
password setup
setup and inquiry
after finishing all setup, press【ESC】key to quit setup.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including:language、password、key-press volumn、key backlight、
default factory setup。The following example is “default factory setup”operation
steps:
In normal status, press and hold 【setup】 key for more than 3s, LCD will Dis
play:
Key in password(default password: 8888), press joystick, LCD will display:
Move the joystick toward down, LCD will display:
Press joystick, LCD will display:
Move joystick till LCD display:
Move joystick toward right, LCD will display:
* default factory
setup
*default factory
setup ?
Move the joystick toward down, LCD will display:
ptz setup
*system setup
*ptz setup
system setup
PTZ addr:028 ④
password:----
— —08
* 0-255
P:PELCO D
PTZ addr:
3.2 System Parameter Setup
*language
password setup
setup and inquiry
after finishing all setup, press【ESC】key to quit setup.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including:language、password、key-press volumn、key backlight、
default factory setup。The following example is “default factory setup”operation
steps:
In normal status, press and hold 【setup】 key for more than 3s, LCD will Dis
play:
Key in password(default password: 8888), press joystick, LCD will display:
Move the joystick toward down, LCD will display:
Press joystick, LCD will display:
Move joystick till LCD display:
Move joystick toward right, LCD will display:
* default factory
setup
*default factory
setup ?
Press joystick, LCD will display:
ptz setup
*system setup
*ptz setup
system setup
PTZ addr:028 ④
password:----
— —08
* 0-255
P:PELCO D
PTZ addr:
3.2 System Parameter Setup
setup and inquiry
after finishing all setup, press【ESC】key to quit setup.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including:language、password、key-press volumn、key backlight、
default factory setup。The following example is “default factory setup”operation
steps:
In normal status, press and hold 【setup】 key for more than 3s, LCD will Dis
play:
Key in password(default password: 8888), press joystick, LCD will display:
Move the joystick toward down, LCD will display:
Press joystick, LCD will display:
Move joystick till LCD display:
Move joystick toward right, LCD will display:
* default factory
setup
*default factory
setup ?
Move joystick till LCD display:
ptz setup
*system setup
*ptz setup
system setup
PTZ addr:028 ④
password:----
— —08
* 0-255
P:PELCO D
PTZ addr:
3.2 System Parameter Setup
*language
password setup
setup and inquiry
after finishing all setup, press【ESC】key to quit setup.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including:language、password、key-press volumn、key backlight、
default factory setup。The following example is “default factory setup”operation
steps:
In normal status, press and hold 【setup】 key for more than 3s, LCD will Dis
play:
Key in password(default password: 8888), press joystick, LCD will display:
Move the joystick toward down, LCD will display:
Press joystick, LCD will display:
Move joystick till LCD display:
Move joystick toward right, LCD will display:
Move joystick toward right, LCD will display:
ptz setup
*system setup
*ptz setup
system setup
PTZ addr:028 ④
password:----
— —08
* 0-255
P:PELCO D
PTZ addr:
3.2 System Parameter Setup
*language
password setup
setup and inquiry
after finishing all setup, press【ESC】key to quit setup.
Note:
If you want to set all PTZ’s protocol and baud rate as same, when you select
PTZ ID in setup menu, please select 0-255, details as below:
Follow above steps, all PTZ’s protocol and baud rate will be set as same.
System parameter including:language、password、key-press volumn、key backlight、
default factory setup。The following example is “default factory setup”operation
steps:
In normal status, press and hold 【setup】 key for more than 3s, LCD will Dis
play:
Key in password(default password: 8888), press joystick, LCD will display:
Move the joystick toward down, LCD will display:
Press joystick, LCD will display:
Move joystick till LCD display:
Move joystick toward right, LCD will display:
* default factory
setup
*default factory
setup ?
6 7