Astonica 50104289 User manual

Brand: Astonica

Model: 50104289

Type: User manual

Astonica 50104289 is a mesh bench intended for residential, non-commercial use. The bench is easy to assemble and can be used both indoors and outdoors. It is made of durable materials that are resistant to heat-induced coloration changes, scratching or alteration due to normal use or weathering. The bench has a sturdy construction and can support a significant amount of weight. It is also easy to clean and maintain. Overall, the Astonica 50104289 is a versatile and practical bench that can be used for a variety of purposes.

Model No: 50104289

Flynn Mesh Bench

Instruction Manual

Read the instructions and precautions before use of this product

Please keep this instruction manual for future reference

Due to ongoing product development

the actual product or products may vary from

the illustrations or photos shown within this manual.

NOTE: This product is intended for residential, non-commercial use.

For warranty information, please refer to the back page of

this instruction manual.

Made in China

Distributed by:

World Factory, Inc.

Westlake, TX 76262

Limited Warranty

World Factory, Inc. Products for Home Use

World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free

from defects in material and workmanship for a period of one (1) year from date of purchase.

SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH

ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE

SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY

FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER

MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This

warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to

normal use or weathering. To make a claim under this Limited Warranty, you must return the complete

product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service

center. Call 1-888-422-7800 for the location of the nearest authorized service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)

YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF

PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such

provision shall not affect any other provision herein, this Limited Warranty shall be construed as if

such invalid and/or unenforceable provision had never been contained herein.

This warranty gives you special legal rights, and you may also have other rights which vary from state

to state.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all

prior agreements, arrangements, or understandings between the parties relating to product warranty.

141011rev1

A Bench Back 1

B Seat 1

C Right Leg 1

D Left Leg 1

E 6m x 32 Bolt 9

F 6m x 15 Bolt 4

G Leg Brace 1

H Hex Key 1

I Nut 1

J Nut Cap 1

K Hex Wrench 1

1. (SEE FIGURE 1) Align the holes in seat (B) with

lower holes in the right leg (C). Secure the leg

to the seat using 6m x 32 bolt (E). Do not

fully tighten bolts.

2. Repeat the ﬁrst step with left leg (D).

3. (SEE FIGURE 2) Align the holes in seat back

(A) to the upper holes in the right and left legs

(C,D). Secure the seat back to the legs using

6m x 32 bolts (E). Secure the middle of the

seat back to the seat using 6m x 32 bolt (E)

and nut (I) tighten with hex wrench (K). Install

nut cap (J) on exposed nut (I). Do not fully

tighten other bolts.

4. (SEE FIGURE 3) Place the leg brace (G) between

the lower part of the right and left legs (C,D).

Align the holes in the brace to the holes in the

legs and secure with 6m x 15 bolt (F). Do not

fully tighten bolts.

5. The legs should sit ﬂat. If the bench rocks,

adjust the bench by moving the arms of the

legs up or down until all four feet of the legs

are ﬂat. Tighten all bolts.

PARTS & HARDWARE LIST

PART # DESCRIPTION QUANTITY

ASSEMBLY INSTRUCTIONS

Figure 1

Figure 3

CAUTION: Do not over tighten fasteners.

Carefully remove the contents from the package. If any parts are missing do not

attempt to use the product until they have been obtained and correctly installed.

NOTE: This product is intended for residential, non-commercial use.

Parts Detail

Figure 2

Astonica 50104289 User manual

Astonica 50104289 User manual

Astonica 50104289 User manual

Related papers

Other documents