AR HDP100 Quick start guide

AR
Brand
AR
Model
HDP100
Category
Car kits
Type
Quick start guide
www.acoustic-research.com
©2008 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) ®Registered
MADE IN CHINA
All rihts reserved. All trade names are registered trademarks
of respective manufacturers listed.
Lorem ipsum dolor sit amet, consectetuer adipiscing elit. Proin ut libero non
tortor vulputate sodales. Sed convallis orci in erat. Nulla vitae neque. Nunc augue
nibh, congue vitae, ultricies id, iaculis sit amet, velit. Sed sed dui. Etiam eget
arcu luctus pede elementum tristique. Integer iaculis. Pellentesque cursus sapien
semper odio. Mauris vel pede eget magna dignissim ullamcorper. Curabitur eget
urna. In faucibus pede at nisi.
Ut blandit cursus neque. Ut semper. Morbi molestie. Praesent vehicula velit eget
nisi. Morbi vel ante id pede fermentum porttitor. Vestibulum faucibus placerat
felis. Sed viverra eros quis tortor. Quisque feugiat elit nec mauris. Praesent elit
magna, pretium sit amet, lobortis vitae, placerat eu, lacus. Aenean id erat.
Lorem ipsum dolor sit amet, consectetuer adipiscing elit. Vestibulum eros nisl,
hendrerit et, pellentesque sit amet, hendrerit id, eros. Phasellus feugiat nisi eu
massa. Fusce accumsan, tellus sit amet sollicitudin eleifend, leo lorem blandit
nibh, id elementum tellus nisi sit amet felis. Class aptent taciti sociosqu ad litora
torquent per conubia nostra, per inceptos himenaeos. Vivamus eget eros.
Quickstart Guide AVAR10303
quickstart guide
Installing and using the
HDP100 in your home
getting started
Congratulations on your purchase
of the AR HD over PLC system, the
HDP100. This guide takes you through
the steps to get started. The rst thing
you’ll have to do is unpack, and check
to make sure your kit has all of the
following parts:
a
b
c
d
e
HDP100 Transmitter
HDP100 Receiver
One Wall Mount Kit
·
Wall mount bracket
·
Two drywall screws
·
Two drywall anchors
One 3’ HDMI cable
Two IR extenders
c
power
link
d a t a
a
power
link
d a t a
b
d
e
Dr yw al l
Anchors
Dr yw al l
Screws
AVAR10303_062008_1.indd 1-3 6/20/08 5:02:01 PM
Note: Your User Guide has more information
about the following setup options:
· Mounting the receiver to your wall
· Using IR extenders to control your signal source through the HDP100
· Using the HDP100 with an A/V receiver or surround sound system
· Using and HDMI splitter to connect more than one signal source to
the HDP100
power
link
d a t a
link the units place the transmitter
& reciever
connect the receiver
& transmitter to your tv
A. Plug in both units in the
same outlet (any outlet).
B. Turn both units on. The
switches are on the back
panels.
C. Press and hold the LINK
button on the back panel
of the transmitter for ve
seconds. The LINK indicator
on the front panel starts
ashing. Now, do the same
thing on the receiver.
· Note: The two units are intro-
ducing themselves to each other
so that they can communicate.
They only have to do this once.
D. When the transmitter and
receiver are linked, the LINK
indicators on the front of
each wll glow steadily
(not ashing). The units are
linked and ready to connect.
E. Turn both units off and
unplug them.
Now you’re ready to nd the
best places for the transmitter
and receiver to reside. Here are
some things to consider as
you’re deciding where the units
should go:
A. Don’t plug into a surge
protector — these interfere
with the communication
between the units. A power
strip is OK to use.
B. Don’t plug into a switchtable
outlet. The units should have
an outlet that always has a
current.
C. Make sure the IR window is
exposed on the receiving unit.
This lets you send remote
commands to the device
connected to the transmitter.
If you want to hide the
receiving unit, you can use
the IR extender.
· Note: See the User Guide
for setup instructions.
attaching the stands:
Find the two stands and four
nylon-topped screws that
came in the package. Line up
the holes on the stand with
the holes on the bottom of
the transmitter or receiver.
Insert the screws and tighten.
A. Connect the receiver to
your TV using the included
HDMI cable.
B. Connect the transmitter
to your signal source (for
example, a DVD player or
satellite receiver). Use a
second HDMI cable (not
included).
C. Plug in and turn on the
transmitter and receiver.
D. Find an outlet or power
strip close to each and
plug them in.
E. Turn on both units. The
Power switches are on the
back panels. The POWER
and LINK indicators should
light up on both. This means
they’re ready to go.
F. Start playing the DVD or
tune to the satellite or cable
channel you want to watch.
The DATA indicator lights
up on the transmitter and
receiver. This means the HD
over PLC system is sending
high-defenition video and
digital audio from your
source to your display.
Enjoy!
· Note: You can also mount the receiver on your wall using
the wall mounting kit that’s included in this package. See
the User Guide for mounting instructions.
s
u
r
g
e
p
r
o
t
e
c
t
o
r
s
s
w
i
t
c
h
t
a
b
l
e
o
u
t
l
e
t
s
· Note: While standard power strips are OK, do not plug the
transmitter or receiver into surge protectors or outlets.
power
link
d a t a
power
link
d a t a
power
link
d a t a
AVAR10303_062008_1.indd 4-6 6/20/08 5:02:04 PM
  • Page 1 1
  • Page 2 2

AR HDP100 Quick start guide

AR
Brand
AR
Model
HDP100
Category
Car kits
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents