Astonica 50104226 User manual

Brand: Astonica

Model: 50104226

Type: User manual

Model No: 50104226

Medium Canopy Hammock

Instruction Manual

Due to ongoing product development

the actual product or products may vary from

the illustrations or photos shown within this manual.

NOTE: This product is intended for residential, non-commercial use.

Made in China

Distributed by:

World Factory, Inc.

Westlake, TX 76262

131210rev1

Please keep this instruction manual for future reference

Read the instructions and precautions before use of this product

For warranty information, please refer to the back page of

this instruction manual.

Limited Warranty

World Factory, Inc. Products for Home Use

World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free

from defects in material and workmanship for a period of one (1) year from date of purchase.

SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH

ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE

SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY

FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER

MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This

warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to

normal use or weathering. To make a claim under this Limited Warranty, you must return the complete

product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service

center. Call 1-888-422-7800 for the location of the nearest authorized service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)

YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF

PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such

provision shall not affect any other provision herein, this Limited Warranty shall be construed as if

such invalid and/or unenforceable provision had never been contained herein.

This warranty gives you special legal rights, and you may also have other rights which vary from state

to state.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all

prior agreements, arrangements, or understandings between the parties relating to product warranty.

A1 Left Support Bar 1

A2 Right Support Bar 1

B Corner Support Bar Connection 4

C End Support Bar 2

D Hammock 1

E Canopy Support 2

F Canopy Middle Support 1

G Canopy Frame Side 2

H Canopy Frame End 2

I Canopy 1

J Canopy Connecting Bolt 2

K Hammock Pillow 1

L Hex Key 1

M Wrench 1

N Feet 2

O Hex Bolt 4

P Canopy Support Straps 2

ASSEMBLY INSTRUCTIONS

PARTS & HARDWARE LIST

PART # DESCRIPTION QUANTITY

C D

J L

Carefully remove the contents from the package. If any parts are missing do not

attempt to use the product until they have been obtained and correctly installed.

CAUTION: Do not over tighten fasteners.

NOTE: This product is intended for residential, non-commercial use.

Parts Detail

7. (SEE FIGURE 7) Align the mounting holes of the canopy frame sides (G) with the ends

of the canopy middle support (F) and secure using the canopy connecting bolts (J).

8. (SEE FIGURE 8) The canopy hammock is

now ready for use.

Figure 7

Figure 8

1. (SEE FIGURE 1) Install hammock pillow

(K) to hammock (D) by connecting straps

as shown. Slide one end support bar (C)

through each sleeve of the hammock (D).

2. (SEE FIGURE 2) Attach two corner support

bar connectors (B) to the left support

bar (A1) by inserting the ends of the left

support bar (A1) into corner support bar

connectors (B) as shown. Repeat process

for remaining two corner support bar

connectors (B) and the right support bar

(A2). Install hammock feet (N) by inserting

into hole on underside of left support bar

(A1) and right support bar (A2).

Figure 1

ASSEMBLY INSTRUCTIONS

Figure 2

3. (SEE FIGURE 3) Align the assembled

support bars (A1/A2) with the hammock

(D) so that the wheels of the support bars

(A1/A2) are on the same end as the

hammock pillow (K). Connect the end

support bars (C) by inserting the ends of

the corner support bar connectors (B) into

the end support bars (C).

Figure 3

ASSEMBLY INSTRUCTIONS

CAUTION: Do not over tighten fasteners.

4. (SEE FIGURE 4) Attach one canopy support (E) to left support bar (A1) by aligning hole

on canopy support (E) with button on the canopy mounting bar (preinstalled to support

bars A1/A2) and pushing onto the canopy mounting bars as shown. Repeat process

for other canopy support (E). Secure canopy supprts (E) by installing canopy support

straps (P) as shown. Install canopy middle supprt (F) by inserting each end into

opening of canopy supports (E) as shown.

5. (SEE FIGURE 5) Install canopy frame ends

(H) by sliding through each sleeve of the

canopy.

Figure 4

Figure 5

6. (SEE FIGURE 6) Align the canopy frame

sides (G) with the canopy frame ends (H)

and insert to connect.

Figure 6

G G

Astonica 50104226 User manual

Astonica 50104226 User manual

Astonica 50104226 User manual

Related papers

Other documents