AGPtek TA4 User manual

Brand: AGPtek

Model: TA4

Type: User manual

TA Series of Temperature Controller

Instruction Manual

Thanks a lot for selecting the product!

Before operating this instrument, please carefully read this

manual and fully understand its contents. If any probroms,

please contact our sales or distributors whom you buy from.

This manual is subject to change without prior notice.

Applications

TA series temperature controller is available for many TC & RTD

input. It adopts some advanced techonology such as multi digital

filter circuit, autotune PID, fuzzy PID that make it much more precise,

stable. It’s widely used in strong anti-interference and automation

systems of mechanism, chemical industrial, chinaware, light industrial,

metallurgy and petroleum chemical industrial. It is also applied to the

production line of foodstuff, packing, printing, dry machine, metal

heat process equipment to control the temperature. simple operation.

Panel

Parameter Setting

MYPIN

Indication lamp: On: active Off: inactive

AT: the auto-tuning operation

AL: the 1st alarm

OUT1: Heating/Main control output

OUT2/AL2: the 2nd control output or the 2nd alarm

<</AT UNDER DISPLAY MODE,

a. Access/Quite auto-tuning estate (press>3s ,AT lamp ON/OFF)

b. Access output preset value modification (press shortly)

UNDER PROGRAMMING MODE,

shift the digit for modification

Increment selected parameter value or selections

Decrement selected parameter value or selections

SET UNDER DISPLAY MODE, Access programming mode

UNDER PROGRAMMING MODE,

a. Store selected parameter and index to next parameter (press shortly)

b. Quite programming mode (press>3s)

Power supply 90-260V AC/DC 50/60Hz

UNDER DISPLAYING MODE

PV displays current temperaturein F /C

SV displays preset output value

UNDER PRAGRAMMING MODE

PV displays parameter

SV displays parameter preset value

Safety Cautions

★ Make sure the power is off before connecting the wires to avoid

electric shock and strickly follow the connection diagram given out

by the factory.

★ Make sure the power is off when cleaning the instrument.

★ Make sure the instrument works under rated voltage to avoid dam

-age or cause fire.

★ Make sure the OUTPUT RELAY works at the rated load and elec

trical life.The relay may melt or burned or even cause fire if it works

agains its electrical life.

Instalation Notice

★ The instrument should be installed in domestic environment.Please

pre-heat for 15 munites before use.

★ Ambient environment: temp: 0℃(32F)~50℃(122F), humidity:

35%~85%RH.

★ To avoid using the instrument in such environment that full of dust,

explosive gas, vapor, or oil.

★To avoid using the instrument in such environment that full of strong

shock,high interference or other factor.

★ The power cable shoudn’t put together with big current cable to

avoid electronmagnetic interference, or use another pip or shield cable.

★ A surge suppressor or noice filter should be installed in case of

noice caused by equipment as motor/transformer/spiral pipe/farrite

cores,etc..

★ The output is active after the power ON fr 10s,please consider this

when configuring cotrol loop.

★The instrument has built-in recoverable fuse to pretect from damage

caused by short-cut circuit. It starts work automatically when

mulfunction is removed.

RELAY: normal open AC 250V/3A DC 30V/3A COS￠=1

Specifications

K 0～999℃/0～1200℃

J 0～999℃ /0～1200℃

T -150～400℃ (Special order)

S 0～1600℃

Rt Pt100 -199～600℃

Cu50 -50～150℃

Input

T/C

Withstand voltage strength

Others

Please mention when ordering

1500V Rms

(Between power terminal and the housing)

Min 50M Ω(500V DC)

(Between power terminal and the housing)

Environment temperature

Save temperature

Environment humidity

Weight

0～50℃

-10～60℃

35～85%RH

Insulation resistance

≤ 350g

E 0～1000℃

Consumption ≤ 5VA

Display range -199～1800℃

Accuracy 0.3%F.S ± 2digit

Sampling cycle ≤ 300ms

Main output RELAY:normal open AC 250V/3A DC 30V/3A COS￠=1

SSR/LOGIC: 24V DC± 2V/ 20mA

Alarm

SSR/LOGIC: 24V DC± 2V/ 20mA

OUT1: R: RELAY S: SSR/Logic

I: 4-20mA V: 0-10V N: None

Power Supply: Default: 90-260V AC/DC

E: 24VDC or 18-30V AC/DC

□□ - □□□□

Models

Input signals:

Default:TC( K,J,E, S) RTD (Pt100,Cu50)

1: 4-20mA 0-10V 0-75mV

2: 4-20mA 0-10V Pt100

F: others (indicate when ordering)

AL1: R: RELAY S: SSR/Logic N: None

Dimension: 4: 48H× 48W 6: 48H × 96W

TA series of temperature controller

7: 72H× 72W 8: 96H × 48W 9: 96H× 96W

OUT2/AL2:

R: RELAY S: SSR/Logic N: None

Press SET or and >3s to enter the parameter setting menu.

A: Press SET to select the parameter to be changed,

B: Press <</AT key to select one of the digits of the setting(value) for

change.

C: Press / to make a change.

D: Press SET to save and move to the next parameter.

NOTE: SV window display convertsion. Under display mode, press

SET to convert display value for OUT or AL1.

↓

Press >3S

SET

↓

AL1(Alarm setting)

range: –1999-9999

AL2 mode: The same as AL1.

Range: ± 100.Display value

PV = Measured value - PVF

Integral time range 0.1-3600. I=OFF means

cancel integral time.

①

AM1(Alarm mode):

0: Deviation HI alarm 1: Deviatian

LO alarm 2: Absolute value HI alarm

3: Absolute value LO alarm 4: Section

outside alarm 5: Section inside alarm

6: TC broken alarm ,The factory setting is 2

Input signal selection TC: K, J, T,E, S

RTD: Pt100, Cu50 The factory setting is K

AL2 set range: –1999-9999.

SET

Shift and flashes

Modify

Stop flashing

Confirm

Self-check

All LED on

＞＞

＞

/AT

Temp. unit

Input type

Current Temp

Preset output value

Max input limit

Min input limit

Power on

↓

Proportional band (%) range 0.1-3600.

If P=OFF, it means ON/OFF control

↓

Proportional band (%) range 0.1-3600.

If P=OFF, it means ON/OFF control

OUT1

SET

/AT

OUT2/AL2

Mounting and Sizes

＋

↑

Sizes

Model

TA4

TA6

TA9

TA7

44.5+0.5 45+0.5 65 65 48 48 8 80

43.5+0.5 91+0.5 65 115 48 96 12 80

67.5+0.5 67.5+0.5 95 95 72 72 12 100

91+0.5 91+0.5 115 115 96 96 12 100

A B C D E F G H

TA8

91+0.5 43.5+0.5 65 115 96 48 12 80

＋

↑

Note:

1.When the user operate the instrument at first time, please

operate according to the processes of this instruction

manual. Let the instrument in autotuning, if the

runing condictions keep not change (eg. Running the

same equipment), the user no need to let it autotuning

again. Because the instrument has recorded the previous

PID parameters. When the instrument is used for huge

capacity heating equipments, the user should set

autotuning value lower 5%-10% than the normal control

value, in order to decrease the exceed-tuning caused by

control.

In normally, the control cycle of the heating equipment

should be 10-20 seconds. For huge capacity heating

equipments, the value should be 30-120 seconds, in

order to longer the use life of the relay. For non-contact

output, such as SSR control output, the value should be 1-3.

Terminal configurations

(If any changed, please refer to the product showing.)

③ Incorrect Control : If the instrument has been used for a long time,

the user find the temperature is hard to rise up to the set value, mean-

while the outsidesystem running well, there must be something wrong

with the parameters of the instrument.

The user need to re-autotuning the instrument. If the instrument lost

control, please check if the connection of the control is correct. If ex-

ternal load is shorted, broken, wrong connection or components is

damaged, it will cause lost control as well. When it is necessary, please

push out the PCB to check the if the output terminals is damaged and

not available.

④ Display malfunction : “UUUU”:

The input signal exeed the measured HI range, or TC break.

ON/OFF control:

←

LO HI

Alarm mode:▲ Set value △ Alarm value AL

LO HI

▲

↑

HYS

▲

Cooling

0:Deviation HI alarm

▲ △

↑

←

LO HI

1:Deviatian LO alarm

△ ▲

↑

←

2:Absolute value HI alarm

▲ △

↑

←

LO HI

3: Absolute value LO alarm

△ ▲

↑

←

LO HI

4: Section outside alarm

△ ▲ △

5: Section inside alarm

△ ▲ △

Malfunction estimate

① No Display : Check all the connection and wiring if it is all correct.

Specially pay attention to the power supply terminals and signal input

ternimals.

② Incorrect Didplay: Check if the input signal is conformity with the

selected symbol.

For TC input, please use the relative compensation cable.

For RTD input, please use low impedence cable. The 3 wires should at

the same length.

If all above mentioned is collect , pleaase use parameter PVF to

modify.

Heating

ON OFF

Note:

All the factory setting value of deiation alarm is 1.0.

▲

1 3

1 2

1 1

1 0

1 5

1 4

1 6

2 4

2 3

2 2

2 1

2 0

1 9

1 8

1 7

com

4-20mA

Application examples

1.Relay output control (forTA4-RNR)

Power supply

Heating cord

Heating

equipment

J-1

FUSE

AL1

OUT1

←

▲

↑

AL1=HIGH ALARM

Parameter lock code setting. LcK=000

means unlocked. LcK=010 means locked.

Temperature unit. C means C degree,

F means F degree.

Only for 4-20mA

=PID control =tPV 4-20mA transmit

High analog output

(when analog is active)

Low analog output

(when analog is active)

The output control mode ,RELAY=020,

SSR\SCR=001,4-20mA=000.

Control directions:

HEAt: heating COOL: cooling

SET

↓

SET

↓

SET

↓

SET

↓

SET

↓

In Non-autotune estate, press and hold / key for more

than 5 seconds can enter/quit the under menu: (Normally

the program will refresh the value of the parameters

by itself, the user no need make modifications. )

＞＞

＞

Up limit value, it is adjustable by the

input signal.

AL1 hysteresis setting value. Range ±90,

factory setting 1.0

AL2 hysteresis setting value. Range ±

90, factory setting 1.0

Password setting.

Factory setting 015

Decimal point setting:

0: No decimal 1: One decimal

RTD

1 0

1 2

1 1

TC/mV

←

1 2

1 1

←

ON OFF

HYS

ON OFF

HYS

OFF

HYS

OFF

HYS

OFF

HYS

OFF

ONOFF

OFF

Low limit value, it is adjustable by the

input signal.

Control hysteresis, range: ± 100.

It is not available when P ≠ OFF

SET

↓

SET

↓

SET

↓

SET

↓

SET

↓

SET

↓

TA4

TA7

RTD

90-260V AC/DC

1 3

1 2

1 0

1 1

AL1

RELAY

OUT1

1 8

1 7

RELAY

OUT2/AL2

▲

SSR

1 5

1 4

1 6

4-20mA

90-260V AC/DC

SSR

4-20mA

AL1

RELAY

OUT1

AL2

RTD

TA6/8

90-260V AC/DC

SSR

AL1

OUT1

LO HI

90-260V AC/DC

AGPtek TA4 User manual

AGPtek TA4 User manual

Other documents