Manual
Automation@Home
www.automation-at-home.com
NO. PLCBUS-5012UK
S3
S2
S1
Telephone Controller (Simple Version)
No. PLCBUS-T 5012UK
Brief Introduction：
With Telephone controller, you can control 256 address
lamps or appliances in your home at anywhere in the world
only through a phone call. So when you are going home, you
can turn on central Air-condition to adjust the temperature in
your home.
Otherwise, it can also let any lamp in your home twinkling
when the telephone is ringing. (This function is very useful to a
person who has impediment with hearing).
Function:
Simple plug-in device;
Local and long-distance telephone control;
Easy and convenient Installation;
Controlling 256 PLCBUS address codes by a call;
Local setup an address by call;
Setting any lamp twinkling when the telephone is ringing.
Installation:
Plug the power supply of telephone controller in any
220V±10% receptacle, and then plug line (or extension line)
in the jack of exterior line.
Technique Spec:
z Rating Voltage 220VAC±10%, 50Hz
z Static State Power ≤1W
z Suitable Temperature -10～50℃
Attention:
Be careful when using Telephone controller to control
appliances in your home. For example: With this product to
control a coffeepot cooking coffee, while no water in coffeepot,
it will be very easy to bring a fire; Also it is so dangerous to
turning on water heater nearby a fabric curtain.
Notice:
1、 Please don’t connect telephone controller with a coin
telephone.
2、 During installing Telephone controller, any problem,
please contact to us, don’t take apart by yourselves.
3、 After voice indicating, the keystrokes are availed.
Usage：
1.
Dialing Telephone controller, then entering the password
(Default password is 1-1-1) into response status;
2. Entering house codes according to phone keyboard
(Range: A～P), then entering Unit code (Range: 01-16);
and pressing
” * ” for Turn On, and ” # ” for Turn Off. If
after the voice indicating “Please enter house code”, you
tap”
# ” button directly, you can Off all the units in your
house (For “All Home Off” command).
3. Repeating above operation, you can control 256 lamps
or appliances.
4.
“S2” button for “ON” function, “S3” button for “OFF”
function. This function is aimed to ON/OFF beforehand
set address. For the detail setting method, please see
below.
Setting Method:
1.
Dialing call number into response status and entering into
password;
2. When voice indicating “Please enter house code”, please
press “S1” and hold for 5 seconds, entering setup status;
then you can here voice indicating “Please enter new
password (Enter 3 number password, except for 0-0-0);
3. Then voice indicating “Please enter ring times”, tap
number 2～8, you can setup how many ring times into our
telephone control system;
A B C D E F G H I J K L M N O P
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
Manual
Automation@Home
www.automation-at-home.com
NO. PLCBUS-5012UK
4. And then voice indicating “Please enter house code”,
“Please enter unit code”, you can setup the address of
button S2, S3 control;
5. Finishing all the setting, voice indicating “Operation
successful” means setting is success and exit setting
status.
Setting some lamp twinkling when the call is coming:
1. Press S3 and hold for 5 seconds, entering into setting
status;
2. Entering house code （A～P）, and then unit code （01-16）,
according above form;
3. “Operation successful” for Setting finished, exiting setting
status.
4.
If you want cancel this function: setup P16 is ok.
Recover to original status；
If you forget the password and can not control with
Telephone controller, you can recover to original status. The
setting method is: press S1 and hold for 15 seconds, the
indicate light flickers once rapidly, it is recovered. During this
process, don’t pay attention to “entering setting status”
indicate. (Ring: 6 times enter telephone system; Password:
1-1-1).
User Code Unify:
Press S1 and hold for 5 seconds, the indicate light flickers
enter setup status, no releasing, use other PLCBUS
4034UK/4036UK send a command, the indicator light stops
flickering means it has unify the User Code from other
controller. (If hold for 15 seconds will recover to original User
Code).
Transfer between 1-Phase and 3-Phase:
Press S2 and S3 button at the same time and hold for 5
seconds, indicator light flickers once for 1-phase status; three
times is for 3-phase status.
Problem resolve：
1. Transmitting ON/OFF command, while some
receiver has no responded.
● Check whether controlled receiver is on power;
● Check whether the unit code of receiver has been set
correctly, meanwhile check whether the address code is the
same between receiver and telephone controller;
● Plug receiver and telephone controller in the same
receptacle, if the receiver can not work well, it is ok just
change a new receiver; if the telephone controller can not
work well, please don’t take apart by yourselves, contact to
us. E-mail to: [email protected].
2. You can not control all the receivers through
telephone controller:
● Check whether the telephone controller is on power;
● Check whether the house code of telephone controller has
been set correctly,
● Plug receiver and telephone controller in the same
receptacle, if you still can not control all the receivers, it is ok
just change a new telephone controller; if the receivers can not
work well, please contact to us. E-mail to: [email protected]
3. If the telephone controller responds the call
rapidly before your telephone responder gets it.
Setting telephone controller delay responds:
15 seconds ≤
the delay time ≤ 35 seconds.
4. Interior communication system：
The interior communication system carrier wave its signal onto
the power line can interfere the telephone controller working
well. Of course, if your interior communication system has its
own special telephone line or using（RF）transmitter, such
condition will not appear.
5. Electric power interrupt：
After electric power interrupts, during the resume process,
generally, lamps and wall switches (receivers) can shut
automatically, while under the power resumed, the appliance
modules still can keep the work state before interrupting.
6. (Local) control for S2 and S3：
If S2 and S3 have no any reaction, please check whether the
beforehand set house code is correct.
coffeepot, etc.)
/