ONKYO CS-1045 (D-145) Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the ONKYO CS-1045 (D-145) Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Speaker System
D-145
Instruction Manual
Thank you for purchasing an Onkyo Speaker System. Please read this manual
thoroughly before using it. Following the instructions in this manual will enable
you to obtain optimum performance and listening enjoyment from your new
Speaker System. Please retain this manual for future reference.
ᅝ㺙᠟ݠ
ᛳ䇶ᙼ䌁фϔ༫᮹ᴀᅝḹ⠠ᡀໄ఼㋏㒳DŽ೼Փ⫼ᴀᡀໄ఼㋏㒳Пࠡˈ䇋䅸
ⳳ䯙䇏ᴀ᠟ݠDŽ䙉ᅜᴀ᠟ݠЁⱘᣛ⼎ˈᙼⱘᮄᡀໄ఼㋏㒳ᇚ݋᳔᳝Շᗻ㛑ˈ
ᙼᇚӮѿফࠄໄ䷇ⱘ㕢཭DŽ䇋ֱ⬭ᴀ᠟ݠˈҹ໛ᇚᴹᶹ䯙DŽ
2
Right speake
r
Left speake
r
Positive (+)
side is indicated
by a red line
Speaker cable
Getting to Know the Speakers
The two speakers are identical, so it doesn’t matter which one you use
on the left or right.
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive devices and as
such are likely to suffer from discoloration or picture distortion when
conventional speakers are placed nearby. Note that discoloration can
also be caused by a magnet or demagnetizing tool that's too close to
your TV or monitor.
Removing the Grills
Using the Cork Spacers
Connection the Speakers
࡮Before connecting the speakers, disconnect your amplifiers power
cord from the wall outlet and set its volume control to minimum.
࡮The speaker’s rated impedance is 4 . Make sure you connect an
amplifier that is compatible with a 4  impedance.
࡮Use the supplied speaker cables to connect the speakers to your
amplifier as shown.
1.Peel the
insulation off
the ends of
the speaker
cable and
twist the
core wires.
2.Loosen the
terminal screw
and insert the
speaker cable
into the hole
(until the core
wires are
inserted fully).
3.Fasten the
terminal
screw.
The type of speaker terminals used on the amplifier and their position
depends on the model. Refer to the amplifiers instruction manual for
details on connecting speakers to the amplifier.
࡮Make sure the speakers positive (+) termi-
nals are connected to the amplifiers positive
(+) terminals, and the speakers negative (–)
terminals are connected to the amplifiers
negative (–) terminals.
࡮Make sure that the positive (+) and negative
(–) wires are not touching each other. If they
are, a short circuit may occur, damaging your
amplifier.
Care
To maintain the appearance of the speakers, you should periodically
wipe them with a soft, dry cloth. Do not use abrasive cloths, thinners,
alcohol, or other solvents that may damage the finish.
Before Using Your New Speakers
࡮
The speaker cabinets are made out of wood and are therefore
sensitive to extreme temperatures and humidity. Do not use
them in locations subject to direct sunlight or in humid
places, such as near an air conditioner, humidifier, bathroom,
or kitchen.
࡮Place the speakers on sturdy, flat surfaces. Putting them on
uneven or unstable surfaces where they may fall and cause
damage will affect the sound quality.
࡮Do not keep water or other liquids close to the speakers. If a
liquid is spilled over them, the woofer and tweeter inside may
be damaged.
࡮Do not handle the speakers with wet or damp hands.
Precautions
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the same
regardless of the color.
The speakers can handle the specified input power when used for
normal music reproduction. If they’re fed any of the following sig-
nals, even if the input power is within the specified rating, exces-
sive current may flow in the speaker coils, causing burning or wire
breakage:
1. Interstation noise from an untuned FM radio.
2. Audio from a cassette that’s being fast-forwarded.
3. High-pitched sounds generated by an oscillator, electronic musi-
cal instrument, and so on.
4. Amplifier oscillation
5. Special test tones from audio test CDs and so on.
6. Thumps and clicks caused by connecting or disconnecting audio
cables (always turn off your amplifier before connecting or dis-
connecting cables).
7. Microphone feedback
The speakers contain powerful magnets. Do not put metal items,
such as screwdrivers, close to the speakers, as they damage to the
tweeter diaphragm.
Specification
Type: 2-way bass reflex
Impedance: 4
Maximum input power: 80 W
Output sound pressure level: 85 dB/W/m
Frequency response: 55 Hz to 35 kHz
Crossover frequency: 3 kHz
Cabinet capacity: 7.5 
Dimensions (W × H × D): 170 × 283 × 230 mm
(incl. grille and projection)
Weight: 3.7 kg
Speakers Woofer: 12 cm OMF cone type
Tweeter: 2.5 cm Soft Dome type
Terminal: Screw-type speaker terminal
Grille: Detachable
Accessories: 1.8 meter speaker cable × 2
Cork spacer × 8
* Specifications and features are subject to change without notice.
Remove
Replace
Grille attachment
catcher
Grille
Tweeter
Cabinet
Woofe
r
Bottom
Cork spacer
3
ϟ
ԡ
ᡀໄ
Ꮊᡀໄ
ℷᵕ˄˅ջ
⫼㑶㒓ᣛ⼎
ᡀໄ
⬉㓚
ᓔྟ䅸䆚ᡀໄ఼
ϸϾᡀໄ఼Ⳍৠˈ಴ℸˈᙼ೼Փ⫼ᯊᎺেϸ䖍ᬒાϔϾഛ
ৃDŽ
೼⬉㾚⬉㛥䰘䖥Փ⫼ᯊⱘ⊼ᛣџ乍
⬉㾚੠⬉㛥ᰒ⼎఼ᰃ⺕ᬣᛳ䆒໛ˈ಴ℸᔧᡞӴ㒳ᡀໄ఼ᬒ㕂
݊䰘䖥ᯊˈৃ㛑Ӯᓩ䍋ব㡆៪೒ڣ༅ⳳDŽ⊼ᛣˈᔧ⺕䪕៪এ
⺕Ꮉ݋⾏⬉㾚៪⬉㛥ᰒ⼎఼䖛䖥ᯊˈгӮᓩ䍋ব㡆DŽ
ᢚ
ϟḐᷙ
Փ
Փ⫼䕃᳼ൿ⠛
䖲᥹ᡀໄ఼
࡮೼䖲᥹ᡀໄ఼Пࠡˈߛᮁᠽ䷇఼⬉⑤㒓Ϣຕ㺙⬉⑤ᦦᑻⱘ
䖲᥹ˈᡞᠽ䷇఼䷇䞣䇗㡖఼䇗㟇᳔ᇣDŽ
࡮䆹ᡀໄ఼ⱘ乱ᅮ䰏ᡫЎ ¡ˈ䇋⹂ֱ᠔䖲᥹ⱘᠽ䷇఼Ϣ
¡䰏ᡫⳌᆍDŽ
࡮
Փ⫼᠔ᦤկⱘᡀໄ఼⬉㓚䖲᥹ᡀໄ఼Ϣᠽ䷇఼ˈབϟ೒᠔
⼎DŽ
1.Peel the
insulation off
the ends of
the speaker
cable and
twist the
core wires.
2.Loosen the
terminal screw
and insert the
speaker cable
into the hole
(until the core
wires are
inserted fully).
3.Fasten the
terminal
screw.
ᠽ䷇఼᠔Փ⫼ⱘᡀໄ఼ッᄤ㉏ൟঞ݊ԡ㕂পއѢᴎൟDŽ݇Ѣ
ᡀໄ఼Ϣᠽ䷇఼䖲᥹ⱘ㒚㡖ˈ䇋ᶹ䯙ᠽ䷇఼ⱘᅝ㺙᠟ݠDŽ
࡮⹂ֱᡀໄ఼ⱘℷᵕ˄ˇ˅ッᄤϢᠽ䷇఼
ⱘℷᵕ˄ˇ˅ッᄤⳌ䖲᥹ˈᡀໄ఼ⱘ䋳
˄ˉ˅ッᄤϢᠽ䷇఼ⱘ䋳˄ˉ˅
ᄤⳌ䖲᥹DŽ
࡮䇋⹂ֱℷᵕ˄ˇ˅Ϣ䋳ᵕ˄ˉ˅ᇐ㒓ϡ
ⳌѦ᥹㾺ˈ৺߭ৃ㛑থ⫳ⷁ䏃ˈᤳണᠽ
䷇఼DŽ
ֱݏ
Ўњ㓈ᣕᡀໄ఼ⱘ໪㾖ˈᑨᅮᳳ⫼ᑆ➹ⱘ䕃Ꮧ᪺ᣁᅗӀDŽϡ
㽕Փ⫼ⷖᏗǃ⿔䞞ࠖǃ䜦㊒៪ৃ㛑ᤳണ䴶ሖⱘ݊ᅗ⒊ࠖDŽ
⫼ࠡ乏ⶹ
࡮䆹ᡀໄ఼ㆅЎ᳼ࠊˈᇍ催⏽╂⑓⦃๗ᵕ݊ᬣᛳDŽ
ℸˈϡ㽕ᡞᡀໄ఼ㆅᬒ㕂೼䰇ܝⳈᇘⱘԡ㕂៪╂⑓
ⱘഎ᠔ˈ՟བ˖ぎ䇗ǃࡴ⑓఼ǃ⍈ᅸ៪ॼ᠓䰘䖥DŽ
࡮ᡞᡀໄ఼ᬒ㕂೼മ೎㗠ᑇ〇ⱘഄᮍˈ৺߭ᯧᇐ㟈݊
ᥝ㨑ǃᤳണˈҢ㗠ᕅડ䷇䋼DŽ
࡮ϡ㽕೼ᡀໄ఼䰘䖥ᄬ⬭∈៪݊ᅗ⎆ԧDŽབᵰ⎆ԧ⑙
ࠄᡀໄ఼ㆅϞˈ߭Ӯᤳണ݊ݙ䚼ⱘ催乥ᡀໄ఼ঞԢ
乥ᡀໄ఼DŽ
࡮⽕⫼⑓᠟㾺ᩌᡀໄ఼DŽ
⊼ᛣџ乍
೼ѻકⳂᔩЁ៪ࣙ㺙Ϟˈѻકৡ⿄㒧ሒᄫ↡㸼⼎ѻક买
㡆DŽ买㡆ϡৠϡᕅડѻક㾘Ḑঞ᪡԰DŽ
ᔧᡀໄ఼㹿⫼Ѣℷᐌⱘ䷇Ф䞡ᬒᯊˈ㛑໳໘⧚乱ᅮⱘ䕧
ܹࡳ⥛DŽབᵰ৥ᡀໄ఼作㒭ϟ߫ӏԩֵোˈ䙷МेՓ䕧
ܹࡳ⥛೼㾘ᅮⱘ乱ᅮؐ㣗ೈݙˈгৃ㛑Ӯ᳝䖛໻⬉⌕⌕
ܹᡀໄ఼㒓೜ݙˈ䗴៤➗⚻៪ᮁ㒓DŽ
˅᳾䇗䇤ⱘ䇗乥ᬊ䷇ᴎথߎⱘৄ䯈ాໄDŽ
˅ᖿ䖯Ⲧᓣ⺕ᏺথߎⱘໄ䷇DŽ
˅⬅ᤃ㤵఼ǃ⬉ᄤФ఼ㄝথߎⱘ催ໄDŽ
˅ᠽ䷇఼ᤃ㤵DŽ
˅⬅䷇乥⌟䆩 &' ㄝথߎⱘ⡍⅞⌟䆩䷇DŽ
˅⬅䖲᥹៪ᮁᓔ䷇乥⬉㓚ᓩ䍋ⱘ⸄ໄ៪Ⓢㄨໄ
˄ᘏᰃ㽕೼䖲᥹៪ᮁᓔ⬉㓚Пࠡ݇䯁ᠽ䷇఼˅DŽ
˅䆱ㄦড作DŽ
䆹ᡀໄ఼ݙ৿ᔎ⺕䪕ˈϡ㽕ᡞ䞥ሲ⠽ક˄՟བ㶎ϱߔ˅
ᬒ೼ᡀໄ఼䰘䖥ˈҹܡᤳӸ催乥ᡀໄ఼ᤃࡼ㝰DŽ
㾘Ḑ
ൟো ঠ䏃Ԣ䷇ডᇘᓣ
䰏ᡫ 
᳔໻䕧ܹࡳ⥛ :
䕧ߎໄय़㑻߿ G%:P
ડᑨ乥⥛ +]ࠄN+]
ߚ乥乥⥛ N+]

ሎᇌ䭓hᆑh催 hhPP
˄ࣙᣀḐᷙ੠さߎ䚼ߚ˅
䞡䞣 NJ
ᡀໄ఼ Ԣ乥ᡀໄ఼  ६㉇ 20) ೚䫹ᔶ
催乥ᡀໄ఼  ६㉇䕃೚乊ᔶ
᥹㒓᷅ 㶎ᮟᓣᡀໄ఼᥹㒓᷅
Ḑᷙ ৃᢚौ
䰘ӊ  ㉇ᡀໄ఼⬉㓚h
䕃᳼ൿ⠛h
㾘ḐϢࡳ㛑ৃ㛑থ⫳᳈ᬍˈᘩϡ঺㸠䗮ⶹDŽ
催乥ᡀໄ఼
Ḑᷙ䖲᥹⟾
Ḑᷙ
ㆅԧ
ᑩ䚼
䕃᳼ൿ⠛
࠹䰸ᡀໄ఼
⬉㓚ッ༈ⱘ
㒱㓬໪Ⲃˈ
ᡞ㢃㒓ᢻ៤
ϔᴳDŽ
ᵒᓔ᥹㒓᷅
㶎ϱˈᡞᡀໄ
఼⬉㓚ᦦܹ
ᄨݙ˄Ⳉࠄ㢃
㒓㹿ᅠܼᦦ
ܹ˅DŽ
ᢻ㋻᥹
㒓᷅㶎
ϱDŽ
Ԣ乥ᡀໄ఼
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
ONKYO CHINA LIMITED
Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung,
N.T., Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.ch.onkyo.com/
SN 29400466
(C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved.
W1006-1
/