Owner’s
Manual
TRA700
IMPORTANT
Read and follow all
Safety Precautions
and Instructions
Before Operating this
Equipment.
Made In CHINA
1602 CORPORATE DRIVE, PO BOX 67 , WARRENSBURG, MISSOURI 64093
PH 660. 747. 8183 FAX 660. 747. 8650
swisherinc.com
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945
ATV Dump Trailer
11783 REV. 08-280
Assembly Instructions
Note: Do not tighten bed bolts until all sheet metal parts are in place.
1. Lay floor (18) on a non-scratching surface (such as carpet or micro-foam packing material) with the flanges
pointing up. Place the sides (20) to the outside of the floor flanges. Loosely secure the fasteners into the center
holes on the sides to the floor panel with four ¼ Carriage Bolts (27), ¼” Flat Washer (30) and ¼”Nylon Locking
nuts (29).
2. Slide the front panel (24) outside of the two sides, matching corresponding holes. Loosely secure the matching
holes with eleven ¼” Carriage Bolts (27), ¼” Flat Washers (30), and ¼” Nylon Locking Nuts (29).
3. Install Rear Stiffener Support (21)(tailgate guides facing out) to floor, using three 3/8” Carriage Bolts (14) and 38”
flat washers (26), and 3/8 Nylon Locking nuts (13). Use eight ¼” carriage bolts ( 27), ¼” Washer (30) and ¼”
nylon lock nut (29), to attach the side to the support.
4. Install the axle (4) to the floor using three 3/8” carriage bolts (14) 3/8” flat washers, and 3/8” nylon locking nuts
(13).
5. Securely tighten all bolts in body assembly.
6. Install wheel hubs w/bearings (1) on the spindles of the axle, making sure that the wheel studs point towards the
outside. Slide the wheel bearing (8) onto the spindle, and into the bearing face of the hub. Secure the hub with
the flat washer(9) and castle nut (10). Do Not Overtighten! Tighten the castle nut to 15 ft/lbs. to eliminate
endplay, making sure the wheel will spin freely. Insert the cotter pin through the castle nut and hole in the
spindle. Bend the ends of the cotter pin over to lock. Tap the dust cap (3) into the hub opening until flange on cap
seats with hub.
7. Bolt the tire & wheel assembly (2) to the hub using the eight wheel lug nuts (6). Tighten the lug nuts to 90 ft/lbs.
(Very Tight)
8. Loosely secure the right and left tongue brackets (19) & (22) to the floor using four 3/8” carriage bolts (14), 3/8”
Flat washer (26), and 3/8” nylon locking nuts (13). Install the tongue (15) ( round end of tongue face to the floor
panel), between the two tongue brackets using one ½” x 3 bolt (11) and ½” lock nut (7). Do Not Over Tighten!
Swing the tongue until it makes contact with the floor and fix the in place using the ½-L pin (5) and spring clip
through the two forward holes in the tongue brackets. Securely tighten all bolts to the floor.
9. Bolt 1 7/8” coupler assembly (12) to the tongue(15)using two 3/8-x 3 bolts (16), 3/8-16 nylon locking nuts (13).
Install safety pin (17) through the hole of the coupler trigger, then install hair pin (32) to lock in place
Note: Check all nuts and bolts occasionally for tightness, and retighten as needed.
Operation and Safety Notes
1. A full capacity load is 700 pounds, DO NOT exceed rated capacity
2. Cart is for ATV or Garden Tractor only, Not for highway use
3. Use caution when operating vehicle as a loaded trailer reduces your ability to stop.
4. Check that the tires are inflated properly. Pressure should be Approximately 5 PSI
5. Check Fasteners periodically, Tighten as needed.
6. Do not exceed manufactures recommended tongue weight, and load capacity.
ITEM # PART # QTY DESCRIPTION ITEM # PART # QTY DESCRIPTION
1 2203 2 Wheel Hub 17 12237 1 Safety Pin
2 2202 2 Tire Assembly 18 2208 1 Floor
3 2203DC 2 Dust Cap 19 2214 1 Right Tongue Bracket
4 2942 1 Axle Assembly 20 2209 2 Side
5 NB606 1 Bent Pin w/ Clip 21 2213 1 Tailgate Support
6 2203LN 8 Lug Nut 22 2214 1 Left Tongue Bracket
7 NB281 1 1/2-13 Lock Nut 23 2217 1 Tailgate
8 2203B 2 Bearing 24 2218 1 Front
9 NB184 2 Flat Washer 25 12245 2 Grease Fitting
10 2203CN 2 Castle Nut 26 NB272 10 3/8" Flat Washer
11 NB131 1 1/2-13 X 3" Bolt 27 10547 23 1/4 X 5/8" Carr. Bolt
12 2201 1 Hitch Assembly 28 NB633 2 Cotter Pin
13 NB182 12 Nylon Lock Nut 29 NB524 23 1/4" Nut
14 10503 10 3/8 X 1"Carriage Bolt 30 NB274 23 1/4 " Washer
15 2216 1 Tongue 31 NB247 1 3 mm Hair Pin Clip
16 NB150 2 3/8-16 X 3" Bolt 32 NB603 1 2mm Hair Pin Clip
ATV Trailer
swisherinc.com
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INORMATION AVAILABLE:
* PRODUCT – ________________
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER WITH PAINT CODE
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE
P.O. BOX 67
WARRENSBURG, MO 64093
ATV & LAWN ACCESSORIES
Owner’s
Manual
TRA700
IMPORTANT
Read and follow all
Safety Precautions
and Instructions
Before Operating this
Equipment.
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Swisher FC-10 User manual
-
-
-
-
-
-
-
-
-
