ESAB CC-11 User manual

  • Hello! I am an AI chatbot trained to assist you with the ESAB CC-11 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the maximum water pressure that the CC-11 can withstand?
    What type of pump does the CC-11 use?
    What is the pump capacity of the CC-11?
    What type of radiator does the CC-11 use?
    What is the enclosure class of the CC-11?
    What is the operating temperature range of the CC-11?
    What is the transportation temperature range of the CC-11?
GB
Valid for serial no. 015-xxx-xxxx0558 007 524 GB 100910
CC-11
Instruction manual
DECLARATION OF CONFORMITY
According to
The Low Voltage Directive 2006/95/EC of 12 December 2006, entering into force 16 January 2007
The EMC Directive 2004/108/EC of 15 December 2004, entering into force 20 January 2005
Type of equipment
Liquid cooling system
Brand name or trade mark
ESAB
Type designation etc.
CC11, Valid from serial number 015 xxx xxxx (2010 w.15)
Manufacturer or his authorised representative established within the EEA
Name, address, telephone number, telefax number:
ESAB AB, Welding Equipment
Esabvägen, SE695 81 LAXÅ, Sweden
Phone: +46 584 81 000, Fax: +46 584 411 924
The following harmonised standard in force within the EEA has been used in the design:
EN 609741, Arc welding equipment – Part 1: Welding power sources
EN 609742, Arc welding equipment – Part 2: Liquid cooling systems
EN 6097410, Arc welding equipment – Part 10: Electromagnetic compatibility (EMC) requirements
Additional information: Restrictive use, Class A equipment, intended for use in locations other than residential
By signing this document, the undersigned declares as manufacturer, or the manufacturer’s authorised
representative established within the EEA, that the equipment in question complies with the safety
requirements stated above.
Date
Laxå 20100412
Signature Position
Global Director
Equipment and Automation
Kent Eimbrodt
Clarification
- 2 -
- 3 -
TOCe
Rights reserved to alter specifications without notice.
1 SAFETY 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INTRODUCTION 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Equipment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 TECHNICAL DATA 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Extra equipment, accessory 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 INSTALLATION 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Lifting instructions 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Mains supply 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Connecting the control cable 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4 Coolant connections 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5 Pressure setting 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 OPERATION 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 Control device and indicators 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 MAINTENANCE 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 Inspection and cleaning 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Filling the coolant 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 FAULT-TRACING 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 ORDERING SPARE PARTS 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- 4 -
bk11e
1 SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in
jury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2. The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3. The workplace must:
S be suitable for the purpose
S be free from drafts
4. Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves. Note! Do not use safety gloves when replacing wire.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
CAUTION!
Read and understand the instruction manual before
installing or operating.
CAUTION!
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
GB
- 5 -
bk11e
WARNING
Read and understand the instruction manual before installing or operating.
Arc welding and cutting can be injurious to yourself and others. Take precausions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S Install and earth the unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S Protect your ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2 INTRODUCTION
This instruction manual contains information about installation and operation of
plasma cooling unit CC-11. The cooling unit circulates coolant for cooling arc cutting
machines and welding equipment.
ESAB's accessories for the product can be found on page 20.
2.1 Equipment
The cooling unit is supplied with:
S Instruction manual
GB
- 6 -
bk11e
3 TECHNICAL DATA
CC-11
Mains voltage 200 / 230 / 400 / 460 / 575 V, ±10 %, 1~ 50/60 Hz
Primary current (A, alternating
current)
9 / 8 / 5 / 4 / 3 A
Cooling capacity
at 50 Hz
at 60 Hz
4,9 kW at 6.0 l/min
5,9 kW at 6.0 l/min
at 25 °C temperature difference between high coolant
temperature and ambient air temperature, when using
ESAB's coolant.
Coolant Ready mixed, see accessories on page 20
Coolant quantity 15.2 litres
Max water pressure 1203 KPa (175 psi )
Operating temperature
10 to 40 °C
Transportation temperature -20 to 55 °C
Dimensions, l x w x h 711 x 552 x 864 mm
Weight
liquid filled
empty
113 kg
97,5 kg
Pump type Displacement pump (vane pump) with adjustable bypass
valve (max. 1375 KPa (200 psi)), clockwise rotation seen
from the identification plate.
Pump capacity 6.0 l/min at 1203 KPa (175 psi)
Radiator type Copper pipe with aluminium flanges, air-water, in
galvanised steel chassis.
Enclosure class IP21
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Apparatus marked IP21 are intended for indoor use.
GB
- 7 -
bk11e
3.1 Extra equipment, accessory
If the cooling unit is installed higher than the plasma torch, a non-return valve must
be installed, see accessories on page 20. Connect the non-return valve to the
COOLANT SUPPLY TO TORCH outlet on the reverse of the cooling unit. The
non-return valve closes if the supply pressure drops below 1719 KPa (250 psi),
which ensures that the coolant does not run out of the cooling unit when replacing
consumables.
Fig 1. The rear panel on the cooling unit
4 INSTALLATION
The installation must be executed by a professional.
WARNING!
ELECTRIC SHOCKS CAN KILL
Always switch off and lock the machine according to the instructions before
making the electrical connections. If conductors are equipped with mains circuit
breakers, the breaker must be set to off and locked with a padlock to prevent
switching on unintentionally. If the included conductors come from a fuse box, the
affected fuses must be removed and the fuse box cover locked with a padlock. If it
is not possible to use a padlock, the mains circuit breaker or fuse box must have a
red notice displayed indicating that the circuit is being worked on.
CAUTION!
Do not run the pump motor intermittently, it causes unnecessary pump wear.
CAUTION!
Do not use solenoid valves that can close when the pump is operating, the pump can
become damaged.
GB
- 8 -
bk11e
Position the cooling unit so that the air flow through the cover's ventilation openings
are not obstructed. Installation hole pattern for permanent installation indicated by
fig. 2.
Hole diameter 13.5 mm, usually 8 pcs.
Fig. 2. Installation hole pattern
4.1 Lifting instructions
WARNING!
The product must be lifted using a fork lift truck.
GB
- 9 -
bk11e
4.2 Mains supply
The cooling unit must be connected with a 3-core cable. Connect the phase
conductors to terminals L1 and L2 on terminal board TB1 and protective earth to the
main earth point on the reverse of the fan bracket.
Fig. 3. Connecting the power supply
Fig. 4. Mains power supply
GB
- 10 -
bk11e
4.3 Connecting the control cable
On the reverse of the cooling unit there is a terminal J1 with 8 pins for connecting
115 VAC operating voltage for the pump motor contactor. The cooling unit is usually
supplied with this operating voltage for pump and fan. J1 is also used for signals for
sufficient flow, 3.8 l/min, pin D and E, and for signals for sufficient coolant level, pin E
and H.
Fig 5. 8-pin female connection
4.4 Coolant connections
Connect the torch coolant connection on the reverse of the cooling unit.
ESAB's coolant is recommended for use. See accessories on page 20.
Fig 6. Coolant connections
GB
- 11 -
bk11e
4.5 Pressure setting
The pressure is controlled by a relief valve next to the pump in the tank. Turn the
pressure setting screw clockwise to increase the pressure and anticlockwise to
reduce the pressure. The pressure is default set to around 1203 KPa (175 psi) at 5.7
l/min. This setting is suitable for plasma torch PT-36 in M3 systems. The setting does
not usually need to be changed if the cooling unit is to be used in any other
application.
Fig. 7. Pressure setting screw
The relief valve allows the coolant to pass through the radiators and back to the
tank.
The pump also has an integrated safety valve, which is default set to be fully open at
1719 KPa (250 psi). It is designed to protect the pump if the external relief valve
jams in the closed position. The relief valve must not be adjusted by the user. If the
external relief valve jams in the closed position and the outlet line is closed, the
pump motor is stopped by a thermostat if the pump temperature exceeds 55 °C.
5 OPERATION
General safety regulations for the handling of the equipment can be found on
page 4. Read through before you start using the equipment!
WARNING!
ELECTRIC SHOCKS CAN KILL
Do not rely on the indicator lamp, disconnect the cooling unit from the power
supply and disconnect the cable at the connection before opening the cover or
carrying out any work on the cooling unit.
GB
- 12 -
bk11e
5.1 Control device and indicators
A. Pump manometer
Indicates the pressure at outgoing
connection. The pressure is default set to
around 1169 - 1203 KPa (170-175 psi) at
5.7 l/min. Lower flow gives greater read off
pressure, greater flow gives lower read off
pressure.
Adjust the pressure using a pressure
regulator near to the coolant tank. The
pressure does not usually need adjusting
by the user, if the pressure regulator is not
replaced or the cooling unit is used for an
application that requires a lower pressure.
The pump is protected by a default set
safety valve. The setting for this valve must
not be changed.
B. Indicator lamp for mains voltage ON
Indicates that incoming power supply is on.
C. Indicator lamp for pump ON
Indicates that the pump and fan motor are powered.
D. Switch Auto/Test
In Auto mode, the pump and fan motors are
powered via the power source's control unit.
In test mode, the pump and fan motors are
powered directly.
E. Indicator lamp for overheating
If the coolant flow through the cooling unit is blocked and the pressure regulator
does not work properly, the pump is protected by the integrated safety valve. After a
few minutes operation under these conditions, however, the pump reaches
temperatures so high that it can become damaged. Too high temperature trips the
pump's thermal cutout.
F. Fuse F1 and F2
Fuses for 230 VAC supply for cooling unit to the fan respectively pump motors.
GB
- 13 -
bk11e
6 MAINTENANCE
WARNING!
ELECTRIC SHOCKS CAN KILL
Take precautionary measures against electric shocks. Ensure that the mains
voltage supply to the machine has been disconnected externally. Switch off the
switch at the wall socket before inspecting or working in the cooling unit. Install all
protection after finishing work. Never use the cooling unit without all the protection
installed.
If the equipment does not work correctly, stop work immediately and determine the
fault of the problem.
CAUTION!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any faults.
Regular maintenance is important for safe, reliable operation.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
6.1 Inspection and cleaning
1. The coolant tank must always be filled with coolant to at least half.
2. Regularly check the coolant pressure and the flow through the system.
3. Regularly check the radiators for dust and other contamination that can affect the
cooling capacity of the cooling unit.
4. Check the filter regularly and clean if necessary. Apply silicone based O-ring
lubricant to the filter's rubber gasket for an optimum seal.
6.2 Filling the coolant
WARNING!
The coolant pump can become damaged if the equipment is used without coolant
in the system.
CAUTION!
The coolant must be handled as chemical waste.
GB
- 14 -
bk11e
S Fill with coolant with 7.5 litres of refrigerant
ESAB's ready mixed coolant is recommended for use. See accessories on page
20.
Note! Coolant must be topped up if connecting a plasma torch or connection
cables that are 5 metres in length or longer. When adjusting the water level by
topping up, the coolant hose does not need to be disconnected.
When the tank has been filled, run the pump with the cover removed to bleed the
radiator, hoses and torch. Check the coolant level in the tank and top up, if
necessary. Reinstall the tank cover.
7 FAULT-TRACING
Try these recommended checks and inspections before sending for an authorised
service technician.
Fault Action
The control panel indicates a
fault code for water flow.
S Check that the cooling unit is running.
S If there is a flow, the water flow guard may be defective.
Poor cooling effect S Clean the cooling element using compressed air.
8 ORDERING SPARE PARTS
Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.
CC-11 is designed and tested in accordance with the international and European stan
dards EN 60974-1, EN 60974-2 and EN 60974-10. It is the obligation of the service unit
which has carried out the service or repair work to make sure that the product still
conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
GB
- 15 -
p
Edition 100910
Diagram
- 16 -
bk11e
Edition 100910
- 17 -
bk11e
Edition 100910
- 18 -
bk11e
CC-11
Edition 100910
Ordering number
- 19 -
bk11o
Ordering no. Denomination
0558 007 515 Cooling unit CC-11
0463 146 086 Instruction manual RU
Instruction manuals are available on the Internet at www.esab.com
CC-11
Edition 100910
Accessories
- 20 -
bk11a
Coolant (Ready mixed) 25% distilled water
and 75% propylene-glycol (10 l) . . . . . . . . . . 0558 004 297
Information on further accessories can be found in separate brochures.
/