Bitspower TITAN ONE MINI 2.0-SW Installation guide

Type
Installation guide

This manual is also suitable for

Parts List
............1 pc
Intel Mounting Bracket
1
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
English
TITAN ONE MINI_2.0 Installation Guide
BPTA-O11D-MINI_CPU_A2.0-SW
CPU Water Block
A
B-1 B-2
A-1
A-2
A-3
The allowable variance in tube length is ± 2mm
248
55
..........1 pc
BPTA-CPUMS-V2-SKA
A-1
A-2
...............1 set
Backplane assembly
A-3
Fittings
B
.................2 pcs
BPTA-DOTFH1622
B-1
....................2 pcs
BPTA-15ATFH16
B-2
Accessory
C
................................4 pcs
Hard tube
C-1
....................1 pc
Fitting + soft tube
C-2
A
B
C
CPU set
C-3
Hard Tube
C-1
Drain Tube
C-2
V15
:16
284
55
:16
BP-CPUPDB-AMD5MS
C-5
BPTA-MKCPUMS-1700 or
BPTA-MKCPUMS-1700-V2
C-4
For standard MATX mother board (24x 24cm).
For the ITX motherboard or not standard size MATX motherboard.
Thumb screw
SPRING
Thumb nut
1mm Spacer
M3x32mm Screw
SC6-32M3
Nylon cup washer
.................4 pcs
.................4 pcs
.................4 pcs
...........4 pcs
..................8 pcs
.....................4 pcs
.........................4 pcs
EX.
I. AMD Motherboard system
2
M3x32mm SCREW
(for Intel)
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
Thumb screw
SPRING
CPU Block
1mm SPACER
Thumb screw
CPU Block
SC6-32M3
(for AMD AM4)
Nylon cup washer
(for AMD AM4)
Original
backplane
SPRING
1mm SPACER
Thumb Nut
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4 + Legacy Installation
DRGB LED
IN
OUT
DRGB PIN on Motherboard or other equipment.
 
Motherboard
Fan and DRGB RF Remote
Controller Hub (Not included)
BPTA-RFCHUB
Do not over-tighten the thumb
screws. The springs should be
slightly compressed, with visible
gaps in the spring coils. Over-tight-
ening may result in poor contact
between the water block and CPU.
Use an appropriate amount
of Thermal Compound, - high-end
Bitspower cooling products are now
available at microcenter.com.
The CPU water block has a DRGB cable, which
can be connected to the DRGB extension
cable of the radiator fans.
Bitspower Fan and DRGB RF Remote Controller Hub
(Not included) are now available at microcenter.com
3
1
4
2
3
Use an appropriate amount
of Thermal Compound
CPU Water block
AM5 Installation
BP-CPUPDB-AMD5MS
C-5
1Thumb screw.................4 PCS
4Stud..........................4 PCS
2Spring .............................4 PCS
3Washer.....................4 PCS
4
Hard tube BPTA-15ATFH16
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
Step 1
Step 2
224~238mm
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
After the hard pipe is installed, please keep the
total length between 224-238mm to ensure
that the waterway will function properly.
Compatible with all mATX boards.
CTL16-90R-55x248(for MATX)
Before installing the water cooling parts for the
graphics card, please remove this part.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
II. Pre-Fill Installation
Hard tube BPTA-15ATFH16
5
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
Step 1
Step 2
260~274mm
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
After the hard pipe is installed, please keep the
total length between 260-274mm to ensure
that the waterway will function properly.
CTL16-90R-55x284(for ITX)
It’s removable
Before installing the water cooling parts for the
graphics card, please remove this part.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
Hard tube BPTA-15ATFH16
6
Thumb screw
SPRING
CPU Block
1mm SPACER
M3x32mm SCREW
(for Intel)
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
Thumb Nut
EX.
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
IN
OUT
A-2
DRGB PIN on Motherboard or other equipment.
 
Motherboard
Fan and DRGB RF Remote
Controller Hub (Not included)
BPTA-RFCHUB
Installation
The CPU water block has a DRGB cable, which
can be connected to the DRGB extension
cable of the radiator fans.
Fin
Base screw
Base
Top
Intel Mounting Bracket
AMD Mounting Bracket
Installation
Do not over-tighten the thumb screws. The
springs should be slightly compressed, with
visible gaps in the spring coils. Over-tighten-
ing may result in poor contact between the
water block and CPU.
Bitspower Fan and DRGB RF Remote Controller Hub
(Not included) are now available at microcenter.com
Use an appropriate amount
of Thermal Compound, - high-end
Bitspower cooling products are now
available at microcenter.com.
Step 1
Step 2
III. Intel Motherboards
7
4
1 2
3
step 1
1
2
3
Installation(LGA 1700)
C-4
Backplate
BPTA-MKCPUMS-1700(If you got this version, please refer to the following installation)
8
step 3
step 2
4
2
9
1
Assembly steps
step 1
1
2
3
Installation(LGA 1700)
BPTA-MKCPUMS-1700-V2(If you got this version, please refer to the following installation)
C-4
Backplate
4
2
3
5
10
step 3
step 2
4
5
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
Step 1
Step 2
224~238mm
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
After the hard pipe is installed, please keep the
total length between 224-238mm to ensure
that the waterway will function properly.
Compatible with all mATX boards.
Before installing the water cooling parts for the
graphics card, please remove this part.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
IV. Pre-Fill Installation
11
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
Step 1
Step 2
224~238mm
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
After the hard pipe is installed, please keep the
total length between 224-238mm to ensure
that the waterway will function properly.
CTL16-90R-55x284(for ITX)
Compatible with all ITX boards.
It’s removable
Before installing the water cooling parts for the
graphics card, please remove this part.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
12
13
BPTA-EFW
It is recommended to install the water-exhaust
fitting at the lowest point of the water cooling
system.
Step 1
Unscrew the top of the water-exhaust fitting.
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
PUMP HEADER
FULL SPEED
AIO_PUMP
CPU_FAN
A Negative electrode -
B positive electrode +
C Speed signal
A B C D
Step 2
Replace with the water-exhaust part. When
screwing in the part, water will start to
discharge, it is recommended to connect
tubing beforehand to control the water outflow.
Pump Spec.
Rated voltage:12V DC
Power consumption:8.4W
Maximum flow:460±15%L/h
Noise:≦24dBA
PWM:Yes
MTBF:≦15,000 hours
Warranty:2 years
Water filling hole
90% full
Before installing the water cooling parts for the
graphics card, please remove this part.
V. Filling and Draining
Notice : Do not turn on the pump if the reservoir is empty.
Only Bitspower Coolant, purified water, or distilled water should be
used for the consumer's liquid-cooling fluid. If the consumer choos-
es different liquid-cooling fluids, the resulting impurities may cause
peeling of the coating on some of the hardware, water channel
block-age by built-up residue, improper operation of the water
pump, water tank tube breakage, and O-ring deformation leading to
leakage. Any issues related to the use of inappropriate liquid-cooling
fluid will be the responsibility of the consumer.
In order to make the internal circulation of the liquid-cooling system
cleaner and avoid the pump stuck by the precipitate, we advise you
torinse the liquid-cooling system with distilled water several times
until theexcluded water is clean. Pour the coolant into the reservoir via the water filling
hole. Once the reservoir is 90% full, turn on the power
supply for the pump to run and let the air exit the loop.
Turn off the power supply when the reservoir is near
empty. Repeat until all the air has exited the loop.
Notice
Before filling with fluid, please make sure all the components are installed correctly. To prevent any leakage
which may damage the PC components, please perform a 24-hour leaking test with only the pump connected
to the power supply.
Bitspower reserves the right to change the product design and interpretations. These are subject to change
without notice. Product colors and accessories are based on the actual product.
When using leak Detector on water cooling loop, in order to avoid product damage due to excessive pressure,
the input pressure should not exceed 0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it will
be the fault of the customer. DO NOT use the Leak Detector when there is water in the loop orthe pump is
running.
Bitspower mandates the use ofdistilled water, purifiedwater, orBitspowerPellucidCoolant as the liquid-cooling
fluid. The consumer may also add Bitspower Dye to Pellucid Coolant for their color preference. Please do not
add any biocide by yourself. If the consumer chooses different liquid-cooling fluid, the resulting impurities may
cause peeling off the coating on some of the hardware, water channels blockage by built-up residue, improper
operation of the water pump, water tank tube breakage, and O-rings deformation or loss sealing leading to
leakage. Any issues related to the use of inappropriate liquid-cooling fluid will be the responsibility of the
consumer.
Do not turn on the pump if the reservoir is empty.
14
Lista de componentes
.........1 pc
Soporte de montaje Intel
1
Spanish
TITAN ONE MINI_2.0 Guía de instalación
BPTA-O11D-MINI_CPU_A2.0-SW
Bloque de refrigeración líquida para CPU
A
B-1 B-2
A-1
A-2
A-3
La variación permitida en la longitud del tubo es de ±2 mm
248
55
..........1 pc
BPTA-CPUMS-V2-SKA
A-1
A-2
..........1 set
Conjunto de placa base
A-3
Equipamiento
B
.................2 pcs
BPTA-DOTFH1622
B-1
....................2 pcs
BPTA-15ATFH16
B-2
Accesorio
C
..........................4 pcs
Tubos rígidos
C-1
......................1 pc
Tubo de drenaje
C-2
A
B
C
CPU set
C-3
Tubos rígidos
C-1
Tubo de drenaje
C-2
V15
:16
284
55
:16
BP-CPUPDB-AMD5MS
C-5
BPTA-MKCPUMS-1700 or
BPTA-MKCPUMS-1700-V2
C-4
Para placa base MATX estándar (24 × 24 cm).
Para placa base ITX o placa base MATX de tamaño no estándar.
Thumb screw
SPRING
Thumb nut
1mm Spacer
M3x32mm Screw
SC6-32M3
Nylon cup washer
.................4 pcs
.................4 pcs
.................4 pcs
...........4 pcs
..................8 pcs
.....................4 pcs
.........................4 pcs
Bitspower se reserva el derecho de modificar el diseño y las interpretaciones
del producto. Estos están sujetos a cambios sin previo aviso. Los colores del
producto y los accesorios se basan en el producto real.
EX.
2
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
Instalación AM4 + Legado
No apriete demasiado los tornillos
de mariposa. Los muelles deben
estar ligeramente comprimidos y
contener espacios visibles en las
espirales. Un apriete excesivo puede
provocar un contacto deficiente
entre el bloque de refrigeración
líquida y la CPU.
I. Placas base para AMD
DENTRO
FUERA
PIN DRGB en la placa base u otro equipo.
 
Placa base
Ventilador y remoto DRGB RF
Controlador (no incluido)
BPTA-RFCHUB
El bloque de refrigeración líquida para CPU tiene
un cable DRGB, que se puede conectar al
cable de extensión DRGB de los
ventiladores del radiador..
El ventilador Bitspower y el controlador remoto DRGB RF
(no incluido) ya están disponibles en microcenter.com
Led DRGB
Tornillo M3×32 mm
(para Intel)
SEPARADOR de 1mm
Almohadilla trasera
Almohadilla adhesiva 3M
Placa base metálica
Tornillo de mariposa
MUELLE
Bloque para CPU
SEPARADOR de 1mm
Tornillo de mariposa
Bloque para CPU
SC6-32M3
(para AMD AM4)
Arandela de copa
de nailon
(para AMD AM4)
Placa base para
AMD original
MUELLE
SEPARADOR de 1mm
Tuerca de mariposa
Utilice una cantidad adecuada de
compuesto térmico. Los productos
de refrigeración de Bitspower de
gama alta ya están disponibles en
microcenter.com.
3
1
4
2
3
Utilice una cantidad adecuada
de compuesto térmico
Bloque para CPU
AM5 Instalación
BP-CPUPDB-AMD5MS
C-5
1Tornillo de mariposa ...4 piezas
4Taco......................4 piezas
2MUELLE ..........................4 piezas
3Arandela...............4 piezas
4
Hard tube BPTA-15ATFH16
Paso 2
224~238mm
Al instalar el tubo rígido desde el bloque de la
CPU hasta el depósito de distribución de
agua, puede mover el tubo rígido a izquierda
y derecha para obtener la longitud de
instalación adecuada.
Una vez instalado el tubo rígido, mantenga la
longitud total entre 224 y 238mm para garan
tizar que el canal funcione correctamente.
Compatible con todas las placas mATX.
CTL16-90R-55x248(for MATX)
Afloje los tornillos.
Ajuste el regulador de acuerdo con la posición del bloque
de la CPU.Ajuste el tubo rígido al mismo nivel que la entrada
del bloque de la CPU.
II. Instalación previa al llenado
Tubos rígidos BPTA-15ATFH16
Paso 1
VELOCIDAD TOTAL
AIO_PUMP
CABEZAL DE LA BOMBA
CABEZAL DE LA BOMBA
CONTROL
PWM
CPU_FAN
Antes de instalar las piezas de refrigeración líquida para la
tarjeta gráfica, retire esta pieza.
5
Afloje los tornillos.
Ajuste el regulador de acuerdo con la posición del bloque
de la CPU.Ajuste el tubo rígido al mismo nivel que la entrada
del bloque de la CPU.
Antes de instalar las piezas de refrigeración líquida para la
tarjeta gráfica, retire esta pieza.
Paso 2
260~274mm
Al instalar el tubo rígido desde el bloque de
la CPU hasta el depósito de distribución de
agua, puede mover el tubo rígido a izquierda
y derecha para obtener la longitud de
instalación adecuada.
Una vez instalado el tubo rígido, mantenga la
longitud total entre 260 y 274mm para garan
tizar que el canal funcione correctamente.
CTL16-90R-55x284(for ITX)
Extraíble
Hard tube BPTA-15ATFH16
VELOCIDAD TOTAL
AIO_PUMP
CABEZAL DE LA BOMBA
CABEZAL DE LA BOMBA
CONTROL
PWM
CPU_FAN
Paso 1
6
EX.
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
A-2
El bloque de refrigeración líquida para CPU tiene
un cable DRGB, que se puede conectar al
cable de extensión DRGB de los
ventiladores del radiador..
Instalación
Instalación
No apriete demasiado los tornillos de mari-
posa. Los muelles deben estar ligeramente
comprimidos y contener espacios visibles en
las espirales. Un apriete excesivo puede
provocar un contacto deficiente
entre el bloque de refrigeración líquida y la
CPU.
Paso 2
III. Placas base Intel
PIN DRGB en la placa base u otro equipo.
 
Placa base
Ventilador y remoto DRGB RF
Controlador (no incluido)
BPTA-RFCHUB
El ventilador Bitspower y el controlador remoto DRGB RF
(no incluido) ya están disponibles en microcenter.com
DENTRO
FUERA
Aleta
Tornillo de la base
Base
Parte superior
Soporte de montaje Intel
Soporte de montaje AMD
Paso 1 Tornillo de mariposa
MUELLE
Bloque para CPU
Separador de 1 mm
Tornillo M3×32mm
(para Intel)
Separador de 1mm
Almohadilla trasera
Almohadilla adhesiva 3M
Placa base metálica
Tuerca de mariposa
Utilice una cantidad adecuada de compuesto
térmico. Los productos de refrigeración de
Bitspower de gama alta ya están disponibles
en microcenter.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Bitspower TITAN ONE MINI 2.0-SW Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI