2. Dometic
  3. Compressor Delay Kit 3314352.018

Dometic Compressor Delay Kit 3314352.018 Installation guide

  • Hello! I have reviewed the Dometic installation instructions for the 3314352.018 Compressor Delay Kit. This document details the installation process and highlights the importance of proper wiring and safety procedures. The kit is designed to delay compressor startup, preventing damage from rapid cycling. I'm here to answer any questions you have about the kit and its installation.
  • What does the compressor delay kit do?
    What does this kit contain?
    Who should install this kit?
3314352.018 COMPRESSOR DELAY KIT
INSTALLATION INSTRUCTIONS
This manual has safety information and instruc-
tions to help users eliminate or reduce the risk
of accidents and injuries.
RECOGNIZE SAFETY INFORMATION
This is the safety alert symbol. It is used to alert
you to personal injury hazards. Obey all safety
messages that follow this symbol to avoid pos-
sible injury or death.
UNDERSTAND SIGNAL WORDS
A signal word, when used with the safety alert
symbol, will identify a safety hazard and its level
of risk for personal injury. A signal word, without
the safety alert symbol, will be used for property
damage messages only.
Read and follow all safety information and
instructions to avoid personal injury.
This kit contains:
1 #10 Sheet metal screw
1 10" White wire with connectors
2 1/4" Female wire connectors
1 Delay module (with jumper wire)
1 3314359.000 Installation Instructions
All eld wiring modications should be made in
compliance with all National, State and local codes.
These instructions must be read and under-
stood before installation of this kit. This kit
must be installed by a Dometic Service Center
or a qualied service technician. Modication
of this product can be extremely hazardous
and could result in personal injury or property
damage.
The compressor delay kit, when installed properly,
will delay compressor start up for 2-1/2 minutes
when 120 VAC power is interrupted or if the thermo-
stat is inadvertently turned off and back on again,
causing the compressor to quick cycle under load.
This will help prevent breaker tripping and may
extend compressor life.
Form No. 3314359.000 6/11
(French 3314360.000)
©2011 Dometic, LLC
LaGrange, IN 46761
GENERAL INSTRUCTIONS
SAFETY INSTRUCTIONS
WARNING indicates a hazard-
ous situation which, if not avoided, could result
in death or serious injury.
CAUTION, used with the safe-
ty alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or
moderate injury.
NOTICE is used to address
practices not related to personal injury.
Information
Step-by-step instructions
FIG. 1
INSTALLATION INSTRUCTIONS
Disconnect 120 VAC. Failure to obey these
instructions could create a shock hazard
causing death or severe personal injury.
1. Shut off 120 VAC and 12 VDC power to air con-
ditioner or heat pump.
2. Remove plastic outside shroud.
3. Locate and remove electrical box cover.
4. Find a suitable location and mount the delay
module inside the electrical box using the #10
sheet metal screw provided. Drill a 9/64" pilot
hole for the screw
Important: Give consideration to location of
blue compressor wire when choosing location.
See Step 7.
*
*
7
MOTOR
COMPRESSOR
C
S
R
O.L.
GRN/YEL
REVERSING VALVE SPLICE CAP
IN-LINE
CONNECTOR
BLK BLK
6 PIN CONN
STEP BLU
BLK
YEL
RED
WHT
1
2
3
4
5
6
RED
WHT
WHT
BLK
RED
YEL
WHT
BRN
FAN
C
HERM
STEP
RUN CAP
RED
START
CAP PTCR
COMP STARTER
6
STEP
9
STEP
8
STEP
GRN/YEL
NOT USED ON
SOME MODELS
5
ICM
HMVR115A9X150
T2 T1
COM
NO NC
WHT
DELAY MODULE
BLUE
BLUE
WHITE
5. Remove one white wire from common terminal of
run capacitor. Connect double spade end of 10"
white wire provided to this terminal. Reconnect
original wire on double spade.
6. Connect the single spade end of white wire to
the T1 tab on the delay module. See FIG. 1.
7. Cut the blue wire that goes to compressor. Make
sure blue wire is cut in a location that will allow
each end to be reconnected to delay module in
Step 8 & 9. Strip both ends of blue wire and install
one 1/4" female wire connector on each end.
8. Connect the blue wire now coming from compres-
sor to the NO tab on delay module. See FIG. 1.
9. Connect the blue wire coming from 6-pin connec-
tor to the double spade tab at T2 on the delay
module. See FIG. 1.
10. Check all connections for tightness and make
sure none will come in contact with electrical
box or cover.
11. Install electrical box cover and plastic outside
shroud.
12. Turn on 120 VAC and 12 VDC and check
operation.
Disconnect the positive (+) 12 VDC terminal
at the supply battery. Damage to equipment
could occur if the 12 VDC is not shut off.
/