2. Home
  3. Home security & automation
  4. Security camera accessories
  5. Williams Sound
  6. WIR TX75 C/D

Williams Sound WIR TX75 C/D, WIR TX75 C User manual

  • Hello! I've reviewed the Quick Setup Guide for the Williams Sound WIR TX75 C/D Infrared Transmitters. This document covers the installation process, including mounting and connection options, and also discusses the use of slave emitters for expanding the coverage area. I'm ready to answer any specific questions you may have about setting up and using the transmitter.
  • What is required for optimal reception?
    Where can the transmitter be mounted?
    How can I increase coverage area?
    What should I check after powering the transmitter?
10300 Valley View Rd • Eden Prairie, MN 55344
800-328-6190 / 952-943-2252 • FAX: 952-943-2174
www.williamssound.com ©2016 Williams Sound • All Rights Reserved
MAN 167E MAN 167E
WIR TX75 C/D Infrared Transmitter
Quick Setup Guide
Determine Transmitter placement
Determine the best location where the WIR TX75 C or WIR TX75 D will
cover the desired area. Remember, IR signals need a clear line of sight to
the receiver for optimum reception. It is usually better to have the transmitter
located above the height of the receiver users.
The transmitter can be mounted on the wall or ceiling with the included
mounting bracket. An optional microphone adapter is available for mounting
to microphone stands. The threaded connector on the top and bottom of the
transmitter is standard to most camera tripods.
Plug the power supply into the transmitter. Make sure the green power LED
is on. Install the audio input cord of your choice and apply signal to the
POWER IN
MIC CHANNEL
SELECTOR
TX75 BUS
OUT TO
SLAVE (1)
(OR POE
INPUT)
TX75 BUS
OUT TO
SLAVE (2)
(OR POE
INPUT)
MIC
IN
CH 1 AUDIO
LEVEL INDICATOR
(YELLOW)
CH 2 AUDIO
LEVEL
INDICATOR
(YELLOW)
SLAVE TRANSMIT
POWER INDICATOR
(YELLOW) SLAVE POWER
INDICATOR
(GREEN)
INDICATOR
LIGHTS
(ON/OFF)
MIC
ADJUSTMENT
POWER
INDICATOR
(3.3) TX75 D (3.8)
(2.3) TX75 C (2.8)
TX75 BUS IN FROM
MASTER
SLAVE TRANSMIT
STATUS INDICATOR (YELLOW)
SLAVE POWER
INDICATOR (GREEN) INDICATOR LIGHTS
(ON/OFF)
A507
PHOENIX INPUTS
WIR TX75 C/D Master Rear View
CEILING MOUNT
FOR MORE DETAILED INFORMATION, PLEASE REFER TO THE INCLUDED MANUAL.
WIR TX75
BKT 024
A176
A177
BKT 024
A178
WIR TX75
TO SLAVE ONLY
DC POWER
MIC
CAT5E
WIR TX75 C/D PRO “MASTER”
WIR TX75 S SLAVE #1
(OPTIONAL)
AUDIO
SOURCE
MICROPHONE
(ELECTRET)
FROM AC
POWER SOURCE
WIR TX75 S SLAVE #2
(OPTIONAL)
A508
POE POWER
(EITHER SLAVE JACK)
FROM AC
POWER
SOURCE
STANDARD
POWER SUPPLY
POE
POWER
SUPPLY
PHOENIX
BKT 024
Universal wall / ceiling
mount (included)
WALL MOUNT
Hardware Mounting Options
transmitter input 1, 2 or both. The audio level indicator should be blinking at
peak audio levels. Be sure that the receivers are set to the same channel/
frequency used on the transmitter.
Important: Remember to point the transmitter towards the listening
audience.
Remember: Most objects block infrared light. The transmitter cannot be
concealed behind walls, glass, curtains, etc.
Optional WIR TX75-S emitter for Additional Coverage
For larger facilities, additional emitters can be used to increase the total
coverage area. The WIR TX75 C/D is capable of driving two WIR TX75-S slave
emitters. Power, baseband and digital data bus are fed via CAT-5e cable to
each TX75-S slave.
Typical Setup with Slave Emitter
Hardware Mounting Options
/