Lumberjack WB1520D1 Owner's manual

Brand: Lumberjack

Model: WB1520D1

Type: Owner's manual

WB1520D1

Safety & Operating Manual

Solid Wood Bench

WB1520D1

TABLE OF CONTENTS

Welcome to Lumberjack!

Dear Customer, Congratulations on your purchase.

Before using the product for the first time please be sure to read these instructions

for use.

They provide you with all information necessary for using the product safely and to

ensure its long service life.

Closely observe all safety information in these instructions!

General Tool Safety Warnings

Specification................................. 01

Parts List..... ........ ...... ..... ..... ............ ........ .............................................02

Assembly

nstructions .....................................................................0

Forestry

ertification............................................................................. 0

WB1520D1

GENERAL TOOL SAFETY WARNINGS

IFI

ATION

WARNING

Read all safety warnings and

all instructions. Failure to follow the warnings

and instructions may result in serious injury.

Save all warnings and instructions for

future reference.

a) Do not exceed weight capacities for the

Workbench shelves and drawers. Be aware of

dynamic loading! Sudden load movement may

briefly create excess load causing product

failure.

b) Use only on flat, level and hard surfaces

capable of supporting the Workbench and any

item(s) placed on Workbench. Evenly distribute

load on Table to avoid tipping.

c) Use as intended only. Do not use Workbench

to perform task for which it was not designed.

d) For indoor use only.

e) Assemble only according to these instructions.

Improper assembly can create hazards.

f) Wear ANSI-approved safety goggles and

heavy-duty work gloves during assembly and

use.

g) Keep assembly area clean and well lit.

h) Keep bystanders out of the area during

assembly.

i) Do not assemble when tired or when under

the influence of drugs or medication.

j) This product is not a toy. Do not allow children

to play with, on or near Workbench.

k) Inspect before every use; do not use if parts

are loose or damaged.

Specifications:

Vice Capacity: 7" Inch

Top Shelf Weight Capacity: 113kg

Drawer Weight Capacity: 11kg

Bottom Shelf Capacity: 90kg

Dimensions (Including Vice):

L)1520mm x W) 620mm x H) 850mm

Drawer Inside Dimensions (x4):

L) 325mm x W) 320mm x H) 70mm

WB1520D1 01

Parts List

Part No Description Qty

WB1520D1

1 Side Legs 2

2 Lower Support Brackets 2

3 Bottom Shelf 1

4 Table Top 1

5 Drawer Back 1

6 Drawer Side 2

7 Drawer Front 1

8 Upper Support Brackets 2

9 Drawer Bottom 1

10 Vice 2

11 Wooden Dogs 4

12 Metal Dogs 4

You will also need a cross head

screwdriver & 13mm spanner to build

this bench

WB1520D1

Fixings

Part No Description Qty

A Allen Key 1

B Dowel Nuts 4

C Long Bolts 4

C1 Washers 8

D Blue Long Screws 4

E Heavy Duty Screws 4

F Blue Small Screws 10

Stage 1 Assembly of work bench frame.

Parts required for this section: A) x1, B)

x4, C) x4, C1) x4, 1) x2, 2) x2 & 3) x1

Place the washer (C1) over bolt (C) and

insert through the side leg (1) to attach the

lower support bracket (2). Place the dowel

nut into the pre cut hole on the support

bracket (2) and tighten using the allen key (A)

Insert bottom shelf (3) by sliding into the

recess of the support bracket (2). Then

attach the second support bracket (2) to the

side legs (1) using bolt (C), washer (C1) &

dowel nut (B)

Repeat this process again for the second

side leg (1) for the bench to then look like

the below image.

Congratulations stage one is now complete.

Your bench should now look like the image

below.

WB1520D1

Stage 2 Attaching the Table top.

Parts required for this section: D) x4, 4)

x1, 8) x2, 10) x1 C1) x4 & E) x4

(You will also require a cross headed screwdriver

& a 13mm spanner)

Attach upper support brackets (8) to the

table top (4) using screws (D)

Attach the table top (4), using

screws (E) & washers (C1). Insert the

screws from underneath the table top

(4)to secure the bench frame.

Once you have secured the table top (4)

with all four screws (E) & washers (C1)

Your bench should then look like the image

below.

Finally, attach the vice (10) to the front of

the table top (4) into the pre drilled holes

on the left.

Congratulations stage two is now complete.

Your bench should now look like the image

below.

Stage 3 Assembly of the drawers.

Parts required for this section: 7) x1,

6) x2, 5) x1, 9) x1 & F) x8

(You will also require a cross headed screwdriver)

To assemble the drawer take both sides (6)

& back (5). Screw together using screws (F)

WB1520D1

Congratulations stage three is now

complete. Your bench is now ready to use.

Once you have screwed the back (5) to

the sides (6) your drawer should look like

this below.

Next take the drawer bottom (9) and slide

into the recess of the sides (6)

Last to do is add the front (7) and secure

tight with screws (F) Then slide the

completed drawer into the recess of the

upper support brackets (8) on the

woodbench.

We wish you many years of enjoyment with your new bench.

Lumberjack WB1520D1 Owner's manual

Lumberjack WB1520D1 Owner's manual

Lumberjack WB1520D1 Owner's manual

Related papers

Other documents