1
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE
INSTRUCTIONS IN THIS MANUAL.
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE
INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE
VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:
LED RADIATION, DO NOT STARE INTO BEAM, CLASS 2 LED PER IEC 60825-1.
For additional information on these led devices with regard to the IEC 60825-1 standard, contact CREE.
SOLID: Protected against solid object greater than 1mm
WATER: Not protected
Suitable for direct mounting on normally flammable surfaces
Minimum distance from lighted objects (0.3 meters)
Rated maximum ambient temperature (indoor with ventilation)
Replace any cracked protective shield or lenses
Index
Dimensions and weight ---------------------------------------------------------------------------------- page 2
Technical data --------------------------------------------------------------------------------------------- page 2
Storage ------------------------------------------------------------------------------------------------------ page 2
Admissible environmental conditions ----------------------------------------------------------------- page 2
Installation ------------------------------------------------------------------------------------------------- page 2
Connection -------------------------------------------------------------------------------------------------- page 3
Cable wiring ------------------------------------------------------------------------------------------------ page 3
Optical specifications ------------------------------------------------------------------------------------- page 4
Lenses -------------------------------------------------------------------------------------------------------- page 4
Power supply ---------------------------------------------------------------------------------------------- page 4
Spare parts ------------------------------------------------------------------------------------------------- page 4
2
Dimensions & weight
= 0,4 Kg
Technical data
- Aluminium body
- IP40 protection rate
- Adjustable bracket, can be installed in any position
- 3 leds white XR-E 1.2W Xlamp by CREE
- Approx. 10 years life (continued use)
- Built-in RJ45 female connector
ATTENTION!!!
Connect the projector only to dedicated power unit.
Up to 20 meters total connection cable (series connection with UTP straight patch cables).
The power unit (LED POWER RGB) can drive up to 10 Mini Light Led.
Storage
The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and +50°C.
Attention, the projector will be damaged during the unpacking.
Admissible environmental conditions
The projector was engineered and produced to function in indoor areas with an air temperature ranging between -10° and
+30°C and with a humidity level between 30 and 90%.
When choosing the installation, please make sure that the device is not exposed to extreme heat or in small area.
If the projector is installed in hot area, led life is decreased.
Installation
The projector is designed to be installed on any materials and in any position.
Use the two hole, 6mm and 9mm, of the bracket for installing the projector.
Uncsrew the side handle and change the projector body angle.
3
Connection
This series of fixtures based on three led’s board, has now a built-in RJ45 female connector
This solution allows the user to get an easier, faster and safer connection.
Connect the projectors to the power unit with standard CAT.5 UTP STRAIGHT PATCH CABLE, and special HUB RJ45.
Example with three fixtures: (3 fixtures, 1 led power, 2 Hub RJ45, 5 UTP straight patch cable)
ATTENTION!!!
Don’t plug in or out the connector from the fixture or from the led power when is connected to the main
power. This non-observance will damage permanently the fixtures and the led power.
Cable wiring
568B SPECIFICATION – CABLE MANUFACTURING INSTRUCTION
PIN ORDER OF THE PLUG
4
Optical specifications
- 3 LEDs white XR-E high power 1.2W Xlamp by CREE
- Approx. 10 years life (continued use)
- Adjustable intensity of each group (with Led Power rgb)
Lenses
There are three types of lenses, see the draw to identify the lense and the beam angle.
Power supply
Disconnect mains power supply before any operations.
Do not power the projector with a dimmer circuit
When in doubt, consult a qualified electrician.
Connect the Mini Light to the power unit (LED POWER RGB) or to the other projectors, 10 max., with special HUB.
Spare parts
When ordering spare parts for the projector remember to mention the model and serial number of the projector.
Call your area dealer or feel free to contact the manufacturer for any additional assistance.
The improper use of this projector, cancel the guarantee and our responsibility. All the information have been written and driven with
extreme care; however, we do not engage us any responsibility for contingent errors or omissions. We reserve the right to modify and/ or
improve our product as we retain necessary, without subsequent warning or notice. It is forbidden any complete or partial reproduction of
this handbook, if not expressly authorized.
/
